Suggestion for proper charging

[T-Dynamos]

Thanks for your code!

I was able to get all info from my battery:

Configured to set charge control pin 9 to low above 95 %
Configured to set discharge control pin 10 to low below 5 % or 3300 mV
No Li-ion supply detected -> fast display timing
Found attached I2C device at address 0xB

*** STATIC INFO ***
Battery mode                        0x0 | 0b0
                                    - Battery OK

Non standard info is supported
Manufacturer Name                   SANYO
0x53 41 4E 59 4F 
Chemistry                           LION
0x4C 49 4F 4E 
Manufacturer Data                   AYN��
0x41 1 6 59 0 0 4E E 90 E 86 E 
Device Name                         AC14B13J
0x41 43 31 34 42 31 33 4A 
Serial number                       46194 | 0xB472
Manufacture date (YYYY-MM-DD)       2015-1-24
Design voltage                      11.400 V
Design capacity                     3270 mAh
Charging current                    0 mA
Charging voltage                    0.000 V
SBM protocol (Version / Revision)   1.1 / 1
Cycle count                         732

Max error of charge calculation     0%
Remaining time alarm                10 min
Remaining capacity alarm            327 mAh

*** MANUFACTURER INFO ***
Device Type                         17928 | 0x4608

*** RATE TEST INFO ***
Setting AT rate to                  100 mA
TimeToFull at rate                  Battery not being (dis)charged - received 0xFFFF
Setting AT rate to                  -100 mA
TimeToEmpty at rate                 Battery not being (dis)charged - received 0xFFFF
Can be delivered for 10 seconds at rate  65535 | 0xFFFF - received 0xFFFF

*** DYNAMIC INFO ***
Relative charge                     1%
Absolute charge                     0%
Full charge capacity                1192 mAh = 36%
Remaining capacity                  11 mAh = 1%
Voltage                             11.107 V
Current                             0 mA
Average current of last minute      0 mA
Temperature                         32.15 C
Minutes remaining until empty       Battery not being (dis)charged - received 0xFFFF
Average minutes remaining until empty  Battery not being (dis)charged - received 0xFFFF
Minutes remaining for full charge   Battery not being (dis)charged - received 0xFFFF
Battery status (BIN)                0x42D0 | 0b100001011010000
                                    - TERMINATE_CHARGE_ALARM
                                    - REMAINING_CAPACITY_ALARM
                                    80 Initialized
                                    40 Discharging
                                    10 Fully Discharged


*** DYNAMIC NON STANDARD INFO / Cell Voltages + SOH ***

*** CHANGED VALUES ***
Temperature                         32.05 C
Voltage                             11.106 V

But now my question is how to charge my battery? Originally my laptop took 19v to charge. I gave 14v to battery it draws 1.5AMP for like 5 mins and stops charging at 2% every time.

Battery status (BIN)                0xC280 | 0b1100001010000000
                                    - OVER_CHARGED_ALARM
                                    - TERMINATE_CHARGE_ALARM
                                    - REMAINING_CAPACITY_ALARM
                                    80 Initialized

Also what is the proper wiring for charging. (I am new to electronics)

Here is my battery link: https://www.batteryclub.org/Goods/ECN10335-AC14B13J-Acer-Battery.html

Thanks Again.

Edit:

[ArminJo]

1. This is NO issue.
2. Start charging with 100 to 500 mA.

[T-Dynamos]

Thanks! Problem was that I ignored (in static info):

Charging current                    1635 mA
Charging voltage                    13.050 V