Compilation errors

[N0ury]

Hi,
I'm trying a new LCD ILI9341.
I get these errors at compile time:

.pio/libdeps/readusersetup/TFT_eSPI/TFT_eSPI.cpp:699:21: error: 'TFT_SWRST' was not declared in this scope
.pio/libdeps/readusersetup/TFT_eSPI/TFT_eSPI.cpp:945:20: error: 'TFT_INIT_DELAY' was not declared in this scope
.pio/libdeps/readusersetup/TFT_eSPI/TFT_eSPI.cpp:3480:23: error: 'TFT_CASET' was not declared in this scope
.pio/libdeps/readusersetup/TFT_eSPI/TFT_eSPI.cpp:3482:23: error: 'TFT_PASET' was not declared in this scope
.pio/libdeps/readusersetup/TFT_eSPI/TFT_eSPI.cpp:3484:23: error: 'TFT_RAMWR' was not declared in this scope
.pio/libdeps/readusersetup/TFT_eSPI/TFT_eSPI.cpp:3556:21: error: 'TFT_CASET' was not declared in this scope
.pio/libdeps/readusersetup/TFT_eSPI/TFT_eSPI.cpp:3560:21: error: 'TFT_PASET' was not declared in this scope
.pio/libdeps/readusersetup/TFT_eSPI/TFT_eSPI.cpp:3564:21: error: 'TFT_RAMRD' was not declared in this scope
.pio/libdeps/readusersetup/TFT_eSPI/TFT_eSPI.cpp:3756:25: error: 'TFT_CASET' was not declared in this scope
.pio/libdeps/readusersetup/TFT_eSPI/TFT_eSPI.cpp:3763:25: error: 'TFT_PASET' was not declared in this scope
.pio/libdeps/readusersetup/TFT_eSPI/TFT_eSPI.cpp:3769:21: error: 'TFT_RAMWR' was not declared in this scope
.pio/libdeps/readusersetup/TFT_eSPI/TFT_eSPI.cpp:4838:20: error: 'TFT_INVON' was not declared in this scope
.pio/libdeps/readusersetup/TFT_eSPI/TFT_eSPI.cpp:4838:32: error: 'TFT_INVOFF' was not declared in this scope

I didn't have these before with an other display.
I get this with the read_user_setup sketch.
I use PlatformIO with arduino framework.
Soc is an ESP32-SOLO-2 on a minimalist custom board.
I must have done something wrong, but I really don't see what.
I need an advice.
Thanks

My platform.ini file:

[env]
platform = espressif32
board = esp32-s2-saola-1
framework = arduino
monitor_speed = 115200
upload_speed = 921600
board_upload.use_1200bps_touch = true
board_upload.wait_for_upload_port = true
board_build.flash_mode = qio
lib_deps = TFT_eSPI
        SPI
        bodmer/TFT_eWidget@^0.0.6
        bodmer/TFT_eSPI@^2.5.33
build_flags = 
     -DCORE_DEBUG_LEVEL=5
     -DARDUINO_USB_CDC_ON_BOOT=1
     -DBOARD_HAS_PSRAM
     -mfix-esp32-psram-cache-issue
        -D USER_SETUP_LOADED=1
        -D ESP32=1
;        -D TFT_INVERSION_OFF=1
        -D ILI9341=1
        -D TFT_WIDTH=240
        -D TFT_HEIGHT=320
        -D TFT_MISO=13
        -D TFT_MOSI=9
        -D TFT_SCLK=46
        -D TFT_CS=12
        -D TFT_DC=10
        -D TFT_RST=11
        -D TFT_BL=3
;	-D TFT_BACKLIGHT_ON=HIGH
        -D SPI_FREQUENCY=27000000
;        -D TFT_RGB_ORDER=TFT_BGR ; Colour order Red-Green-Blue
        -D LOAD_GLCD=1   ; Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
        -D LOAD_FONT2=1  ; Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
        -D LOAD_FONT4=1  ; Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
        -D LOAD_FONT6=1  ; Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
        -D LOAD_FONT7=1  ; Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
        -D LOAD_FONT8=1  ; Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
#       -D LOAD_FONT8N=1 ; Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
        -D LOAD_GFXFF=1  ; FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
        -D SMOOTH_FONT=1

[env:readusersetup]
    build_src_filter = +<readusersetup.cpp>

[N0ury]

My bad!
It's not -D ILI9341=1 but -D ILI9341_DRIVER=1
Sorry for the noise.