ESU8285 flash size corrected

Author: Def3nder

platformio.ini

@@ -75,8 +75,8 @@ build_flags =
   ; -D WLED_DISABLE_ALEXA
   -D WLED_DISABLE_BLYNK
   -D WLED_DISABLE_CRONIXIE
-  ; -D WLED_DISABLE_HUESYNC
-  -D WLED_DISABLE_INFRARED
+  -D WLED_DISABLE_HUESYNC
+  ; -D WLED_DISABLE_INFRARED
 
 [common:esp8266_512k]
 platform = [email protected]
@@ -126,13 +126,13 @@ lib_deps =
 
 [env:esp8285]
 board = esp8285
-platform = ${common:esp8266.platform}
+platform = [email protected]
 monitor_speed = ${common.monitor_speed}
 upload_speed = ${common.upload_speed}
 framework = ${common.framework}
 build_flags =
-  ${common.build_flags}
-  ${common:esp8266.build_flags}
+  -D PIO_FRAMEWORK_ARDUINO_LWIP2_HIGHER_BANDWIDTH_LOW_FLASH
+  -Wl,-Teagle.flash.1m256.ld  ;;;; Compile with no SPIFFS to leave space for OTA
   -D WLED_DISABLE_BLYNK
   -D WLED_DISABLE_CRONIXIE
   -D WLED_DISABLE_HUESYNC

wled00/NpbWrapper.h

@@ -5,8 +5,8 @@
 //PIN CONFIGURATION
 #define LEDPIN 2  //strip pin. Any for ESP32, gpio2 or 3 is recommended for ESP8266 (gpio2/3 are labeled D4/RX on NodeMCU and Wemos)
 //#define USE_APA102 // Uncomment for using APA102 LEDs.
-#define BTNPIN 0  //button pin. Needs to have pullup (gpio0 recommended)
-#define IR_PIN 3 //infrared pin (-1 to disable)  MagicHome: 4, H801 Wifi: 3
+#define BTNPIN -1 //button pin. Needs to have pullup (gpio0 recommended)
+#define IR_PIN  0 //infrared pin (-1 to disable)  MagicHome: 4, H801 Wifi: 0
 #define RLYPIN -1 //pin for relay, will be set HIGH if LEDs are on (-1 to disable). Also usable for standby leds, triggers,...
 #define AUXPIN -1 //debug auxiliary output pin (-1 to disable)
 
@@ -21,18 +21,18 @@
 #endif
 
 #ifndef WLED_DISABLE_ANALOG_LEDS
-  /*PWM pins - PINs 5,12,13,15 are used with Magic Home LED Controller
-  #define RPIN 5    //R pin for analog LED strip   
-  #define GPIN 12   //G pin for analog LED strip
-  #define BPIN 13   //B pin for analog LED strip
-  #define WPIN 15   //W pin for analog LED strip
-  */
-  //PWM pins - PINs 15,13,12,14 are used with H801 Wifi LED Controller
+  //PWM pins - PINs 15,13,12,14 (W2 = 04)are used with H801 Wifi LED Controller
   #define RPIN 15   //R pin for analog LED strip   
   #define GPIN 13   //G pin for analog LED strip
   #define BPIN 12   //B pin for analog LED strip
-  #define WPIN 14   //W pin for analog LED 
+  #define WPIN 14   //W pin for analog LED strip (W1: 14, W2: 04)
   //
+  /*PWM pins - PINs 5,12,13,15 are used with Magic Home LED Controller
+  #define RPIN 5   //R pin for analog LED strip   
+  #define GPIN 12   //G pin for analog LED strip
+  #define BPIN 13   //B pin for analog LED strip
+  #define WPIN 15   //W pin for analog LED strip (W1: 14, W2: 04)
+  */
 #endif
 
 //automatically uses the right driver method for each platform