Merge pull request #216410 from LouisBerner/v-lberner-ADO_2002217

updated article per notes from convo w/ Alpa

Author: prmerger-automator[bot]

articles/databox-online/azure-stack-edge-pro-2-deploy-install.md

@@ -7,7 +7,7 @@ author: alkohli
 ms.service: databox
 ms.subservice: edge
 ms.topic: tutorial
-ms.date: 05/17/2022
+ms.date: 11/08/2022
 ms.author: alkohli
 zone_pivot_groups: azure-stack-edge-device-deployment
 # Customer intent: As an IT admin, I need to understand how to install Azure Stack Edge Pro 2 in datacenter so I can use it to transfer data to Azure.  
@@ -85,6 +85,9 @@ This device is shipped in a single box. Complete the following steps to unpack y
     - One power cord.
     - One packaged bezel.
     - A pair of packaged Wi-Fi antennas in the accessory box.
+      > [!NOTE]
+      > The accessory box includes Wi-Fi antennas, but Wi-Fi capability is not supported for the Azure Stack Edge device. The antennas should not be used.
+
     - One packaged mounting accessory which could be:
         - A 4-post rack slide rail, or
         - A 2-post rack slide, or 
@@ -104,6 +107,9 @@ This device is shipped in two boxes. Complete the following steps to unpack your
     - One power cord.
     - One packaged bezel.
     - A pair of packaged Wi-Fi antennas in the accessory box.
+      > [!NOTE]
+      > The accessory box includes Wi-Fi antennas, but Wi-Fi capability is not supported for the Azure Stack Edge device. The antennas should not be used.
+
     - One packaged mounting accessory which could be:
         - A 4-post rack slide rail, or
         - A 2-post rack slide, or 
@@ -216,6 +222,8 @@ Before you start cabling your device, you need the following things:
 - Access to one power distribution unit.
 - At least one 100-GbE network switch to connect a 10/1-GbE or a 100-GbE network interface to the internet for data. At least one data network interface from among Port 2, Port 3, and Port 4 needs to be connected to the Internet (with connectivity to Azure).
 - A pair of Wi-Fi antennas (included in the accessory box).
+    > [!NOTE]
+    > The accessory box includes Wi-Fi antennas, but Wi-Fi capability is not supported for the Azure Stack Edge device. The antennas should not be used.
 
 ::: zone-end
 
@@ -234,7 +242,9 @@ Before you start cabling your device, you need the following things:
     For a full list of supported cables, modules, and switches, see [Connect-X6 DX adapter card compatible firmware](https://docs.nvidia.com/networking/display/ConnectX6DxFirmwarev22271016/Firmware+Compatible+Products). 
 - At least one 100-GbE network switch to connect a 1-GbE or a 100-GbE network interface to the internet for data for each device.
 - A pair of Wi-Fi antennas (included in the accessory box).
- 
+    > [!NOTE]
+    > The accessory box includes Wi-Fi antennas, but Wi-Fi capability is not supported for the Azure Stack Edge device. The antennas should not be used.
+
 ::: zone-end
 
 > [!NOTE]
@@ -303,20 +313,6 @@ Follow these steps to cable your device for power:
 
 ::: zone-end
 
-### Wi-Fi antenna installation
-
-Follow these steps to install Wi-Fi antennas on your device: 
-
-1. Locate the two Wi-Fi SMA RF threaded connectors on the back plane of the device. These gold-colored connectors are located on the faceplate of PCIe card slot, right below Port 3 and Port 4.
-
-1. Use a clockwise motion to thread the antennas onto the SMA connectors. Secure them using only your fingers. Do not use a tool or wrench.
-
-    >[!NOTE]
-    > Tighten the connectors sufficiently so that the antenna's rotary joints can turn without causing the threaded connectors to become loose.
-
-1. To position the antennas as desired, articulate the hinge and turn the rotary joint.
-
-
 ### Network cabling
 
 ::: zone pivot="single-node"