Tidy up part nos and swapped I2C/UART on BMC.

Mark all resistors as 1% if not specified.
Added some Mouser part numbers.
BMC can now be programmed over UART.

Author: thejpster

CubeMX/STM32 Board Management Controller.ioc

@@ -44,9 +44,9 @@ RCC.HCLKFreq_Value=48000000
 Mcu.IPNb=10
 TIM2.IPParameters=Channel-PWM Generation3 CH3,Channel-PWM Generation4 CH4
 ProjectManager.PreviousToolchain=
-PB6.Signal=USART1_TX
+PB6.Signal=I2C1_SCL
 PB5.PinState=GPIO_PIN_SET
-PB6.Mode=Asynchronous
+PB6.Mode=I2C
 PA8.GPIOParameters=GPIO_Label
 Mcu.Pin6=PA4
 Mcu.Pin7=PA5
@@ -75,7 +75,7 @@ PB1.GPIO_Label=DC_ON
 File.Version=6
 PA0.Mode=IN0
 PB3.GPIOParameters=GPIO_Label
-PB7.Signal=USART1_RX
+PB7.Signal=I2C1_SDA
 PA8.Signal=GPIO_Output
 SPI1.VirtualNSS=VM_NSSHARD
 NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:false\:false
@@ -90,7 +90,7 @@ NVIC.TimeBase=TIM1_BRK_UP_TRG_COM_IRQn
 ProjectManager.ToolChainLocation=
 PA2.GPIO_Label=LED0
 NVIC.TimeBaseIP=TIM1
-PA10.Signal=I2C1_SDA
+PA10.Signal=USART1_RX
 PA15.Signal=GPXTI15
 PB5.GPIO_Label=PS2_DAT1
 RCC.APB1TimFreq_Value=48000000
@@ -110,7 +110,7 @@ TIM2.Channel-PWM\ Generation4\ CH4=TIM_CHANNEL_4
 PA7.Mode=Full_Duplex_Slave
 Mcu.PinsNb=31
 PA15.GPIOParameters=GPIO_Label
-PA10.Mode=I2C
+PA10.Mode=Asynchronous
 ProjectManager.NoMain=false
 SPI1.IPParameters=VirtualType,Mode,Direction,VirtualNSS
 VP_ADC_TempSens_Input.Mode=IN-TempSens
@@ -121,10 +121,10 @@ RCC.FamilyName=M
 USART1.VirtualMode-Asynchronous=VM_ASYNC
 PA13.Signal=SYS_SWDIO
 PA15.Locked=true
-PA9.Mode=I2C
+PA9.Mode=Asynchronous
 PA8.GPIO_Label=HOST_NIRQ
 ProjectManager.TargetToolchain=Makefile
-PA9.Signal=I2C1_SCL
+PA9.Signal=USART1_TX
 I2C1.Timing=0x20303E5D
 PB5.Locked=true
 ProjectManager.RegisterCallBack=
@@ -184,7 +184,7 @@ NVIC.ForceEnableDMAVector=true
 KeepUserPlacement=false
 ProjectManager.CompilerOptimize=6
 PA11.Signal=USART1_CTS
-PB7.Mode=Asynchronous
+PB7.Mode=I2C
 VP_IWDG_VS_IWDG.Signal=IWDG_VS_IWDG
 PA14.Signal=SYS_SWCLK
 ProjectManager.HeapSize=0x200

Kicad/Neotron-Common-Hardware-cache.lib

@@ -181,6 +181,31 @@ X Pin_4 4 -200 -200 150 R 50 50 1 1 P
 ENDDRAW
 ENDDEF
 #
+# Connector_Generic_Conn_01x05
+#
+DEF Connector_Generic_Conn_01x05 J 0 40 Y N 1 F N
+F0 "J" 0 300 50 H V C CNN
+F1 "Connector_Generic_Conn_01x05" 0 -300 50 H V C CNN
+F2 "" 0 0 50 H I C CNN
+F3 "" 0 0 50 H I C CNN
+$FPLIST
+ Connector*:*_1x??_*
+$ENDFPLIST
+DRAW
+S -50 -195 0 -205 1 1 6 N
+S -50 -95 0 -105 1 1 6 N
+S -50 5 0 -5 1 1 6 N
+S -50 105 0 95 1 1 6 N
+S -50 205 0 195 1 1 6 N
+S -50 250 50 -250 1 1 10 f
+X Pin_1 1 -200 200 150 R 50 50 1 1 P
+X Pin_2 2 -200 100 150 R 50 50 1 1 P
+X Pin_3 3 -200 0 150 R 50 50 1 1 P
+X Pin_4 4 -200 -100 150 R 50 50 1 1 P
+X Pin_5 5 -200 -200 150 R 50 50 1 1 P
+ENDDRAW
+ENDDEF
+#
 # Connector_Generic_Conn_01x06
 #
 DEF Connector_Generic_Conn_01x06 J 0 40 Y N 1 F N

Kicad/Neotron-Common-Hardware.sch

@@ -694,6 +694,7 @@ F 4 "0" H 4025 4675 50  0001 C CNN "DNP"
 F 5 "A31722-ND" H 4025 4675 50  0001 C CNN "Digikey"
 F 6 "5-5530843-0" H 4025 4675 50  0001 C CNN "MPN"
 F 7 "TE" H 4025 4675 50  0001 C CNN "Manufacturer"
+F 8 "571-5-5530843-0" H 4025 4675 50  0001 C CNN "Mouser"
 	1    4025 4675
 	1    0    0    -1  
 $EndComp
@@ -811,6 +812,7 @@ F 4 "0" H 5950 4675 50  0001 C CNN "DNP"
 F 5 "A31722-ND" H 5950 4675 50  0001 C CNN "Digikey"
 F 6 "5-5530843-0" H 5950 4675 50  0001 C CNN "MPN"
 F 7 "TE" H 5950 4675 50  0001 C CNN "Manufacturer"
+F 8 "571-5-5530843-0" H 5950 4675 50  0001 C CNN "Mouser"
 	1    5950 4675
 	1    0    0    -1  
 $EndComp
@@ -928,6 +930,7 @@ F 4 "0" H 7775 4675 50  0001 C CNN "DNP"
 F 5 "A31722-ND" H 7775 4675 50  0001 C CNN "Digikey"
 F 6 "5-5530843-0" H 7775 4675 50  0001 C CNN "MPN"
 F 7 "TE" H 7775 4675 50  0001 C CNN "Manufacturer"
+F 8 "571-5-5530843-0" H 7775 4675 50  0001 C CNN "Mouser"
 	1    7775 4675
 	1    0    0    -1  
 $EndComp
@@ -1051,6 +1054,7 @@ F 4 "0" H 9625 4675 50  0001 C CNN "DNP"
 F 5 "A31722-ND" H 9625 4675 50  0001 C CNN "Digikey"
 F 6 "5-5530843-0" H 9625 4675 50  0001 C CNN "MPN"
 F 7 "TE" H 9625 4675 50  0001 C CNN "Manufacturer"
+F 8 "571-5-5530843-0" H 9625 4675 50  0001 C CNN "Mouser"
 	1    9625 4675
 	1    0    0    -1  
 $EndComp