updates from ante

Author: CamDavidsonPilon

static/img/user-guide/hardware-assembly/instructions.png

@@ -32,7 +32,7 @@ You will need the following items to assemble your Pioreactor:
 <AssemblyInstructionBlock title="Step 2: Use all the information available to you" images={["user-guide/hardware-assembly/instructions.png", "user-guide/hardware-assembly/label_reference.jpg"]}>
 
 - Before starting a step, read all instructions and view all photos at the bottom of each step.
-- Most of the labels are scaled 1:1 and can be used to identify parts.
+- Most of the labels on the packaging are scaled 1:1 and can be used to identify parts.
 
 :::info
 Missing a part? Email us at `[email protected]`, we're happy to help.

user-guide/01-getting-started/01-assembly_guides/00_pioreactor_40ml_v1.5/01-40ml-v15-introduction.md

@@ -60,7 +60,7 @@ The vial holder comes in two halves; a top vial holder and a bottom vial holder.
 
 1. Insert the other end of the flex cable below the O-ring and into <Highlight color={colors.red}>the groove</Highlight>. Pull it through.
 2. <Highlight color={colors.magenta}>Apply pressure</Highlight> on the back of the heater PCB so that it lies flat on the O-ring. Maintain this pressure for the next steps.
-3.  **While maintaining pressure**, flip the holder and insert the two <Highlight color={colors.green}>M2.5-CS 5mm screws</Highlight> into the holes - **don't tighten fully yet**.
+3.  **While maintaining pressure**, flip the holder and insert the two <Highlight color={colors.green}>M2.5-CS 4mm screws</Highlight> into the holes - **don't tighten fully yet**.
 4. **While maintaining pressure**, take turns screwing each in until both are reasonably tight, and the heater PCB is securely attached to the bottom vial holder.
 
 </AssemblyInstructionBlock>

user-guide/01-getting-started/01-assembly_guides/00_pioreactor_40ml_v1.5/03-40ml-v15-wetware-assembly.md

@@ -44,7 +44,7 @@ The top faceplate comes with a button extension to provide easier access to push
 
 1. Flip over the assembly.
 2. Insert the 10mm screw into the hole under the button extension.
-3. Place <Highlight color={colors.red}>one finger behind the extension</Highlight> and <Highlight color={colors.magenta}>apply torque with the other hand</Highlight> until the screw is secure in the hole. This may require some force. Once established, you can use a screwdriver to finish screwing it in until you feel sufficient resistance. Don't over-tighten!
+3. Place <Highlight color={colors.red}>one finger behind the extension</Highlight> and <Highlight color={colors.magenta}>rotate with the other hand</Highlight> until the screw is secure in the hole. Don't over-tighten! Once established, you can use a screwdriver to finish screwing it in until you feel sufficient resistance. Don't over-tighten!
 
 </AssemblyInstructionBlock>
 

user-guide/01-getting-started/01-assembly_guides/00_pioreactor_40ml_v1.5/04-40ml-v15-faceplate-all-together.md

@@ -75,7 +75,7 @@ It does not matter which wires are connected to either eye-spy sockets. However,
 
 1. Connect the LED cable to the <Highlight color={colors.green}>Channel A connector</Highlight>.
 2. Secure <Highlight color={colors.purple}>LED caps (3x) over the unused pockets</Highlight>. 
-3. Insert the LED bulb into the pocket labeled IR. _Slowly_ bend the bulb's leads 90 degrees towards the left.
+3. Insert the LED bulb into the pocket labeled IR. _Slowly_ bend the bulb's leads 90 degrees towards the left such that the bend is near the LED bulb.
 4. Secure the bulb with an LED cap. 
 
 

user-guide/01-getting-started/01-assembly_guides/00_pioreactor_40ml_v1.5/05-40ml-v15-optics-assembly.md

@@ -32,7 +32,7 @@ You will need the following items to assemble your Pioreactor:
 <AssemblyInstructionBlock title="Step 2: Use all the information available to you" images={["user-guide/hardware-assembly/instructions.png", "user-guide/hardware-assembly/label_reference.jpg"]}>
 
 - Before starting a step, read all instructions and view all photos at the bottom of each step.
-- Most of the labels are scaled 1:1 and can be used to identify parts.
+- Most of the labels on the packaging are scaled 1:1 and can be used to identify parts.
 
 :::info
 Missing a part? Email us at `[email protected]`, we're happy to help.

user-guide/01-getting-started/01-assembly_guides/01_pioreactor_20ml_v1.5/01-20ml-v15-introduction.md

@@ -18,7 +18,8 @@ import TabItem from '@theme/TabItem';
 1. Gather the 20ml vial, stirbar, and stainless steel ports.
 2. Remove the cap from the vial.
 3. Gently but firmly push the stainless steel ports into the four holes. The two straight ports are placed in the <Highlight color={colors.blue}>outer holes</Highlight>, and the two bent ports are placed in the <Highlight color={colors.orange}>inner holes</Highlight>. 
-4. Place the stirbar in the vial and secure the cap. 
+4. Position the ports about **half way** through the vial cap for now. These can be adjusted later.
+5. Place the stirbar in the vial and secure the cap.
 
 </AssemblyInstructionBlock>
 
@@ -57,7 +58,7 @@ import TabItem from '@theme/TabItem';
 
 1. Insert the other end of the flex cable below the O-ring and into <Highlight color={colors.red}>the groove</Highlight>. Pull it through.
 2. <Highlight color={colors.magenta}>Apply pressure</Highlight> on the back of the heater PCB so that it lies flat on the O-ring. Maintain this pressure for the next steps.
-3.  **While maintaining pressure**, flip the holder and insert the two <Highlight color={colors.green}>M2.5-CS 5mm screws</Highlight> into the holes - **don't tighten fully yet**.
+3.  **While maintaining pressure**, flip the holder and insert the two <Highlight color={colors.green}>M2.5-CS 4mm screws</Highlight> into the holes - **don't tighten fully yet**.
 4. **While maintaining pressure**, take turns screwing each in until both are reasonably tight, and the heater PCB is securely attached to the bottom vial holder.
 
 </AssemblyInstructionBlock>

user-guide/01-getting-started/01-assembly_guides/01_pioreactor_20ml_v1.5/03-20ml-v15-wetware-assembly.md

@@ -46,7 +46,7 @@ The top faceplate comes with a button extension to provide easier access to push
 
 1. Flip over the assembly.
 2. Insert the 10mm screw into the hole under the button extension.
-3. Place <Highlight color={colors.red}>one finger behind the extension</Highlight> and <Highlight color={colors.magenta}>apply torque with the other hand</Highlight> until the screw is secure in the hole. This may require some force. Once established, you can use a screwdriver to finish screwing it in until you feel sufficient resistance. Don't over-tighten!
+3. Place <Highlight color={colors.red}>one finger behind the extension</Highlight> and <Highlight color={colors.magenta}>rotate with the other hand</Highlight> until the screw is secure in the hole. Don't over-tighten! Once established, you can use a screwdriver to finish screwing it in until you feel sufficient resistance. Don't over-tighten!
 
 </AssemblyInstructionBlock>
 

user-guide/01-getting-started/01-assembly_guides/01_pioreactor_20ml_v1.5/04-20ml-v15-faceplate-all-together.md

@@ -75,7 +75,7 @@ It does not matter which wires are connected to either eye-spy sockets. However,
 
 1. Connect the LED cable to the <Highlight color={colors.green}>Channel A connector</Highlight>.
 2. Secure an<Highlight color={colors.purple}>LED cap over the unused pocket</Highlight>. 
-3. Insert the LED bulb into the pocket labeled IR. _Slowly_ bend the bulb's leads 90 degrees towards the left.
+3. Insert the LED bulb into the pocket labeled **IR**. _Slowly_ bend the bulb's leads 90 degrees towards the left such that the bend is near the LED bulb.
 4. Secure the bulb with an LED cap. 
 
 

user-guide/01-getting-started/01-assembly_guides/01_pioreactor_20ml_v1.5/05-20ml-v15-optics-assembly.md

@@ -33,7 +33,7 @@ You will need the following items to assemble your Pioreactor:
 <AssemblyInstructionBlock title="Step 2: Use all the information available to you" images={["user-guide/hardware-assembly/instructions.png", "user-guide/hardware-assembly/label_reference.jpg"]}>
 
 - Before starting a step, read all instructions and view all photos at the bottom of each step.
-- Most of the labels are scaled 1:1 and can be used to identify parts.
+- Most of the labels on the packaging are scaled 1:1 and can be used to identify parts.
 
 :::info
 Missing a part? Email us at `[email protected]`, we're happy to help.