consolidated hardware pages into 1

Author: hartk1213

manual/20-Intro.md

@@ -1,6 +1,6 @@
-# Introduction
+# INTRODUCTION
 
-### STL File Key
+### STL FILE KEY
 
 
 | **Primary Color** | **Accent Color** | **Quantity Required** |

manual/30-hardware.md

@@ -1,4 +1,6 @@
-# HARDWARE 
+# HARDWARE REFERENCES
+
+### FASTENERS
 
 | <object type="image/svg+xml" data="images/Vectors/hardware/m3_bhcs.svg" class="hardware_svg"> m3_bhcs.svg </object> | <object type="image/svg+xml" data="images/Vectors/hardware/m3_fhcs.svg" class="hardware_svg"> m3_fhcs.svg </object> | <object type="image/svg+xml" data="images/Vectors/hardware/m3_shcs.svg" class="hardware_svg"> m3_shcs.svg </object> | <object type="image/svg+xml" data="images/Vectors/hardware/m3_gs.svg" class="hardware_svg"> m3_gs.svg </object> |
 | --- | --- | --- | --- |
@@ -12,3 +14,16 @@
 | GT2 pulley used on the motion system of the Micron. | Hex nuts couple with bolts to create a tight, secure joint. You’ll see these used in both M2 and M3 variants throughout this guide. | Fastener with a pronounced thread profile that is screwed directly into plastic. | Heat the inserts with a soldering iron so that they melt the plastic when installed. As the plastic cools, it solidifies around the knurls and ridges on the insert for excellent resistance to both torque and pull-out. |
 |  | ISO 4032 / DIN 934 | ISO 4762 / DIN 912 |  |
 
+### MOTION COMPONENTS
+
+| <object type="image/svg+xml" data="images/Vectors/hardware/f623_bearing.svg" class="hardware_svg"> f623_bearing.svg </object> | <object type="image/svg+xml" data="images/Vectors/hardware/625_bearing.svg" class="hardware_svg"> 625_bearing.svg </object> | <object type="image/svg+xml" data="images/Vectors/hardware/f623_bearing.svg" class="hardware_svg"> f623_bearing.svg </object> | <object type="image/svg+xml" data="images/Vectors/hardware/m3_shims.svg" class="hardware_svg"> m3_shims.svg </object> |
+| --- | --- | --- | --- |
+| **F623 BEARING** | **625 BEARING** | **F695 BEARING (OPTIONAL)** | **M3 SHIM** |
+| A ball bearing with a 3mm ID and flange for containing the belt used in various gantry locations. | A ball bearing with used in the Z drive. | A ball bearing with a 5mm ID and flange used as an upper support on the A/B Stepper Motors shaft. | Not to be confused with stamped washers. These are used in all M3 call-out locations in this manual. |
+|  |  |  | 3x6x0.5 DIN 988 |
+
+| <object type="image/svg+xml" data="images/Vectors/hardware/m3_shims.svg" class="hardware_svg"> m3_shims.svg </object> | <object type="image/svg+xml" data="images/Vectors/hardware/5mmx47mm_shaft.svg" class="hardware_svg"> 5mmx47mm_shaft.svg </object> |  | | 
+| --- | --- | --- | --- |
+| **M5 SHIM** | **5MM X 47-50MM SHAFT** | **6MM X 3MM MAGNET** | |
+| Not to be confused with stamped washers. These are used in the Z drive assembly. | Steel shaft, 5mm in diameter, 47mm-50mm long with a flat ground on it used in the Z drive shaft assembly. | 6mm Diameter disc magnet, 3mm thick. These are used in various locations of the build, typically held in place with CA glue |  |
+| 5x7x1 DIN 988 |  |  |  |

manual/31-hardware.md

@@ -1,4 +1,4 @@
-# HARDWARE 
+### TEST 123
 
 | <object type="image/svg+xml" data="images/Vectors/hardware/f623_bearing.svg" class="hardware_svg"> f623_bearing.svg </object> | <object type="image/svg+xml" data="images/Vectors/hardware/625_bearing.svg" class="hardware_svg"> 625_bearing.svg </object> | <object type="image/svg+xml" data="images/Vectors/hardware/f623_bearing.svg" class="hardware_svg"> f623_bearing.svg </object> | <object type="image/svg+xml" data="images/Vectors/hardware/m3_shims.svg" class="hardware_svg"> m3_shims.svg </object> |
 | --- | --- | --- | --- |