drm/amd/display: Remove min_dst_y_next_start check for Z8

[Why]
Flickering occurs on DRR supported panels when engaged in DRR due to
min_dst_y_next becoming larger than the frame size itself.

[How]
In general, we should be able to enter Z8 when this is engaged but it
might be a net power loss even if the calculation wasn't bugged.

Don't support enabling Z8 during the DRR region.

Cc: [email protected] # 6.1+
Reviewed-by: Syed Hassan <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Nicholas Kazlauskas <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>

Author: Nicholas Kazlauskas

drivers/gpu/drm/amd/display/dc/dml/dcn20/dcn20_fpu.c

@@ -950,10 +950,8 @@ static enum dcn_zstate_support_state  decide_zstate_support(struct dc *dc, struc
 {
 	int plane_count;
 	int i;
-	unsigned int min_dst_y_next_start_us;
 
 	plane_count = 0;
-	min_dst_y_next_start_us = 0;
 	for (i = 0; i < dc->res_pool->pipe_count; i++) {
 		if (context->res_ctx.pipe_ctx[i].plane_state)
 			plane_count++;
@@ -975,26 +973,15 @@ static enum dcn_zstate_support_state  decide_zstate_support(struct dc *dc, struc
 	else if (context->stream_count == 1 &&  context->streams[0]->signal == SIGNAL_TYPE_EDP) {
 		struct dc_link *link = context->streams[0]->sink->link;
 		struct dc_stream_status *stream_status = &context->stream_status[0];
-		struct dc_stream_state *current_stream = context->streams[0];
 		int minmum_z8_residency = dc->debug.minimum_z8_residency_time > 0 ? dc->debug.minimum_z8_residency_time : 1000;
 		bool allow_z8 = context->bw_ctx.dml.vba.StutterPeriod > (double)minmum_z8_residency;
 		bool is_pwrseq0 = link->link_index == 0;
-		bool isFreesyncVideo;
-
-		isFreesyncVideo = current_stream->adjust.v_total_min == current_stream->adjust.v_total_max;
-		isFreesyncVideo = isFreesyncVideo && current_stream->timing.v_total < current_stream->adjust.v_total_min;
-		for (i = 0; i < dc->res_pool->pipe_count; i++) {
-			if (context->res_ctx.pipe_ctx[i].stream == current_stream && isFreesyncVideo) {
-				min_dst_y_next_start_us = context->res_ctx.pipe_ctx[i].dlg_regs.min_dst_y_next_start_us;
-				break;
-			}
-		}
 
 		/* Don't support multi-plane configurations */
 		if (stream_status->plane_count > 1)
 			return DCN_ZSTATE_SUPPORT_DISALLOW;
 
-		if (is_pwrseq0 && (context->bw_ctx.dml.vba.StutterPeriod > 5000.0 || min_dst_y_next_start_us > 5000))
+		if (is_pwrseq0 && context->bw_ctx.dml.vba.StutterPeriod > 5000.0)
 			return DCN_ZSTATE_SUPPORT_ALLOW;
 		else if (is_pwrseq0 && link->psr_settings.psr_version == DC_PSR_VERSION_1 && !link->panel_config.psr.disable_psr)
 			return allow_z8 ? DCN_ZSTATE_SUPPORT_ALLOW_Z8_Z10_ONLY : DCN_ZSTATE_SUPPORT_ALLOW_Z10_ONLY;