Merge tag 'net-next-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from Jakub Kicinski:
 "Core & protocols:

   - Large effort by Eric to lower rtnl_lock pressure and remove locks:

      - Make commonly used parts of rtnetlink (address, route dumps
        etc) lockless, protected by RCU instead of rtnl_lock.

      - Add a netns exit callback which already holds rtnl_lock,
        allowing netns exit to take rtnl_lock once in the core instead
        of once for each driver / callback.

      - Remove locks / serialization in the socket diag interface.

      - Remove 6 calls to synchronize_rcu() while holding rtnl_lock.

      - Remove the dev_base_lock, depend on RCU where necessary.

   - Support busy polling on a per-epoll context basis. Poll length and
     budget parameters can be set independently of system defaults.

   - Introduce struct net_hotdata, to make sure read-mostly global
     config variables fit in as few cache lines as possible.

   - Add optional per-nexthop statistics to ease monitoring / debug of
     ECMP imbalance problems.

   - Support TCP_NOTSENT_LOWAT in MPTCP.

   - Ensure that IPv6 temporary addresses' preferred lifetimes are long
     enough, compared to other configured lifetimes, and at least 2 sec.

   - Support forwarding of ICMP Error messages in IPSec, per RFC 4301.

   - Add support for the independent control state machine for bonding
     per IEEE 802.1AX-2008 5.4.15 in addition to the existing coupled
     control state machine.

   - Add "network ID" to MCTP socket APIs to support hosts with multiple
     disjoint MCTP networks.

   - Re-use the mono_delivery_time skbuff bit for packets which user
     space wants to be sent at a specified time. Maintain the timing
     information while traversing veth links, bridge etc.

   - Take advantage of MSG_SPLICE_PAGES for RxRPC DATA and ACK packets.

   - Simplify many places iterating over netdevs by using an xarray
     instead of a hash table walk (hash table remains in place, for use
     on fastpaths).

   - Speed up scanning for expired routes by keeping a dedicated list.

   - Speed up "generic" XDP by trying harder to avoid large allocations.

   - Support attaching arbitrary metadata to netconsole messages.

  Things we sprinkled into general kernel code:

   - Enforce VM_IOREMAP flag and range in ioremap_page_range and
     introduce VM_SPARSE kind and vm_area_[un]map_pages (used by
     bpf_arena).

   - Rework selftest harness to enable the use of the full range of ksft
     exit code (pass, fail, skip, xfail, xpass).

  Netfilter:

   - Allow userspace to define a table that is exclusively owned by a
     daemon (via netlink socket aliveness) without auto-removing this
     table when the userspace program exits. Such table gets marked as
     orphaned and a restarting management daemon can re-attach/regain
     ownership.

   - Speed up element insertions to nftables' concatenated-ranges set
     type. Compact a few related data structures.

  BPF:

   - Add BPF token support for delegating a subset of BPF subsystem
     functionality from privileged system-wide daemons such as systemd
     through special mount options for userns-bound BPF fs to a trusted
     & unprivileged application.

   - Introduce bpf_arena which is sparse shared memory region between
     BPF program and user space where structures inside the arena can
     have pointers to other areas of the arena, and pointers work
     seamlessly for both user-space programs and BPF programs.

   - Introduce may_goto instruction that is a contract between the
     verifier and the program. The verifier allows the program to loop
     assuming it's behaving well, but reserves the right to terminate
     it.

   - Extend the BPF verifier to enable static subprog calls in spin lock
     critical sections.

   - Support registration of struct_ops types from modules which helps
     projects like fuse-bpf that seeks to implement a new struct_ops
     type.

   - Add support for retrieval of cookies for perf/kprobe multi links.

   - Support arbitrary TCP SYN cookie generation / validation in the TC
     layer with BPF to allow creating SYN flood handling in BPF
     firewalls.

   - Add code generation to inline the bpf_kptr_xchg() helper which
     improves performance when stashing/popping the allocated BPF
     objects.

  Wireless:

   - Add SPP (signaling and payload protected) AMSDU support.

   - Support wider bandwidth OFDMA, as required for EHT operation.

  Driver API:

   - Major overhaul of the Energy Efficient Ethernet internals to
     support new link modes (2.5GE, 5GE), share more code between
     drivers (especially those using phylib), and encourage more
     uniform behavior. Convert and clean up drivers.

   - Define an API for querying per netdev queue statistics from
     drivers.

   - IPSec: account in global stats for fully offloaded sessions.

   - Create a concept of Ethernet PHY Packages at the Device Tree level,
     to allow parameterizing the existing PHY package code.

   - Enable Rx hashing (RSS) on GTP protocol fields.

  Misc:

   - Improvements and refactoring all over networking selftests.

   - Create uniform module aliases for TC classifiers, actions, and
     packet schedulers to simplify creating modprobe policies.

   - Address all missing MODULE_DESCRIPTION() warnings in networking.

   - Extend the Netlink descriptions in YAML to cover message
     encapsulation or "Netlink polymorphism", where interpretation of
     nested attributes depends on link type, classifier type or some
     other "class type".

  Drivers:

   - Ethernet high-speed NICs:
      - Add a new driver for Marvell's Octeon PCI Endpoint NIC VF.
      - Intel (100G, ice, idpf):
         - support E825-C devices
      - nVidia/Mellanox:
         - support devices with one port and multiple PCIe links
      - Broadcom (bnxt):
         - support n-tuple filters
         - support configuring the RSS key
      - Wangxun (ngbe/txgbe):
         - implement irq_domain for TXGBE's sub-interrupts
      - Pensando/AMD:
         - support XDP
         - optimize queue submission and wakeup handling (+17% bps)
         - optimize struct layout, saving 28% of memory on queues

   - Ethernet NICs embedded and virtual:
      - Google cloud vNIC:
         - refactor driver to perform memory allocations for new queue
           config before stopping and freeing the old queue memory
      - Synopsys (stmmac):
         - obey queueMaxSDU and implement counters required by 802.1Qbv
      - Renesas (ravb):
         - support packet checksum offload
         - suspend to RAM and runtime PM support

   - Ethernet switches:
      - nVidia/Mellanox:
         - support for nexthop group statistics
      - Microchip:
         - ksz8: implement PHY loopback
         - add support for KSZ8567, a 7-port 10/100Mbps switch

   - PTP:
      - New driver for RENESAS FemtoClock3 Wireless clock generator.
      - Support OCP PTP cards designed and built by Adva.

   - CAN:
      - Support recvmsg() flags for own, local and remote traffic on CAN
        BCM sockets.
      - Support for esd GmbH PCIe/402 CAN device family.
      - m_can:
         - Rx/Tx submission coalescing
         - wake on frame Rx

   - WiFi:
      - Intel (iwlwifi):
         - enable signaling and payload protected A-MSDUs
         - support wider-bandwidth OFDMA
         - support for new devices
         - bump FW API to 89 for AX devices; 90 for BZ/SC devices
      - MediaTek (mt76):
         - mt7915: newer ADIE version support
         - mt7925: radio temperature sensor support
      - Qualcomm (ath11k):
         - support 6 GHz station power modes: Low Power Indoor (LPI),
           Standard Power) SP and Very Low Power (VLP)
         - QCA6390 & WCN6855: support 2 concurrent station interfaces
         - QCA2066 support
      - Qualcomm (ath12k):
         - refactoring in preparation for Multi-Link Operation (MLO)
           support
         - 1024 Block Ack window size support
         - firmware-2.bin support
         - support having multiple identical PCI devices (firmware needs
           to have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
         - QCN9274: support split-PHY devices
         - WCN7850: enable Power Save Mode in station mode
         - WCN7850: P2P support
      - RealTek:
         - rtw88: support for more rtw8811cu and rtw8821cu devices
         - rtw89: support SCAN_RANDOM_SN and SET_SCAN_DWELL
         - rtlwifi: speed up USB firmware initialization
         - rtwl8xxxu:
             - RTL8188F: concurrent interface support
             - Channel Switch Announcement (CSA) support in AP mode
      - Broadcom (brcmfmac):
         - per-vendor feature support
         - per-vendor SAE password setup
         - DMI nvram filename quirk for ACEPC W5 Pro"

* tag 'net-next-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2255 commits)
  nexthop: Fix splat with CONFIG_DEBUG_PREEMPT=y
  nexthop: Fix out-of-bounds access during attribute validation
  nexthop: Only parse NHA_OP_FLAGS for dump messages that require it
  nexthop: Only parse NHA_OP_FLAGS for get messages that require it
  bpf: move sleepable flag from bpf_prog_aux to bpf_prog
  bpf: hardcode BPF_PROG_PACK_SIZE to 2MB * num_possible_nodes()
  selftests/bpf: Add kprobe multi triggering benchmarks
  ptp: Move from simple ida to xarray
  vxlan: Remove generic .ndo_get_stats64
  vxlan: Do not alloc tstats manually
  devlink: Add comments to use netlink gen tool
  nfp: flower: handle acti_netdevs allocation failure
  net/packet: Add getsockopt support for PACKET_COPY_THRESH
  net/netlink: Add getsockopt support for NETLINK_LISTEN_ALL_NSID
  selftests/bpf: Add bpf_arena_htab test.
  selftests/bpf: Add bpf_arena_list test.
  selftests/bpf: Add unit tests for bpf_arena_alloc/free_pages
  bpf: Add helper macro bpf_addr_space_cast()
  libbpf: Recognize __arena global variables.
  bpftool: Recognize arena map type
  ...

Author: torvalds

.get_maintainer.ignore

@@ -1,4 +1,5 @@
 Alan Cox <[email protected]>
 Alan Cox <[email protected]>
 Christoph Hellwig <[email protected]>
+Jeff Kirsher <[email protected]>
 Marc Gonzalez <[email protected]>

.mailmap

@@ -573,6 +573,7 @@ Simon Kelley <[email protected]>
 Sricharan Ramabadhran <[email protected]> <[email protected]>
 Srinivas Ramana <[email protected]> <[email protected]>
 Sriram R <[email protected]> <[email protected]>
+Stefan Wahren <[email protected]> <[email protected]>
 Stéphane Witzmann <[email protected]>
 Stephen Hemminger <[email protected]> <[email protected]>
 Stephen Hemminger <[email protected]> <[email protected]>

Documentation/ABI/testing/sysfs-class-net-queues

@@ -96,3 +96,26 @@ Description:
 		Indicates the absolute minimum limit of bytes allowed to be
 		queued on this network device transmit queue. Default value is
 		0.
+
+What:		/sys/class/net/<iface>/queues/tx-<queue>/byte_queue_limits/stall_thrs
+Date:		Jan 2024
+KernelVersion:	6.9
+Contact:	[email protected]
+Description:
+		Tx completion stall detection threshold in ms. Kernel will
+		guarantee to detect all stalls longer than this threshold but
+		may also detect stalls longer than half of the threshold.
+
+What:		/sys/class/net/<iface>/queues/tx-<queue>/byte_queue_limits/stall_cnt
+Date:		Jan 2024
+KernelVersion:	6.9
+Contact:	[email protected]
+Description:
+		Number of detected Tx completion stalls.
+
+What:		/sys/class/net/<iface>/queues/tx-<queue>/byte_queue_limits/stall_max
+Date:		Jan 2024
+KernelVersion:	6.9
+Contact:	[email protected]
+Description:
+		Longest detected Tx completion stall. Write 0 to clear.

Documentation/admin-guide/sysctl/net.rst

@@ -206,6 +206,11 @@ Will increase power usage.
 
 Default: 0 (off)
 
+mem_pcpu_rsv
+------------
+
+Per-cpu reserved forward alloc cache size in page units. Default 1MB per CPU.
+
 rmem_default
 ------------
 

Documentation/bpf/kfuncs.rst

@@ -177,10 +177,10 @@ In addition to kfuncs' arguments, verifier may need more information about the
 type of kfunc(s) being registered with the BPF subsystem. To do so, we define
 flags on a set of kfuncs as follows::
 
-        BTF_SET8_START(bpf_task_set)
+        BTF_KFUNCS_START(bpf_task_set)
         BTF_ID_FLAGS(func, bpf_get_task_pid, KF_ACQUIRE | KF_RET_NULL)
         BTF_ID_FLAGS(func, bpf_put_pid, KF_RELEASE)
-        BTF_SET8_END(bpf_task_set)
+        BTF_KFUNCS_END(bpf_task_set)
 
 This set encodes the BTF ID of each kfunc listed above, and encodes the flags
 along with it. Ofcourse, it is also allowed to specify no flags.
@@ -347,10 +347,10 @@ Once the kfunc is prepared for use, the final step to making it visible is
 registering it with the BPF subsystem. Registration is done per BPF program
 type. An example is shown below::
 
-        BTF_SET8_START(bpf_task_set)
+        BTF_KFUNCS_START(bpf_task_set)
         BTF_ID_FLAGS(func, bpf_get_task_pid, KF_ACQUIRE | KF_RET_NULL)
         BTF_ID_FLAGS(func, bpf_put_pid, KF_RELEASE)
-        BTF_SET8_END(bpf_task_set)
+        BTF_KFUNCS_END(bpf_task_set)
 
         static const struct btf_kfunc_id_set bpf_task_kfunc_set = {
                 .owner = THIS_MODULE,

Documentation/bpf/map_lpm_trie.rst

@@ -17,7 +17,7 @@ significant byte.
 
 LPM tries may be created with a maximum prefix length that is a multiple
 of 8, in the range from 8 to 2048. The key used for lookup and update
-operations is a ``struct bpf_lpm_trie_key``, extended by
+operations is a ``struct bpf_lpm_trie_key_u8``, extended by
 ``max_prefixlen/8`` bytes.
 
 - For IPv4 addresses the data length is 4 bytes