Getting Started with Seeed Studio XIAO ESP32S3 Series | Seeed Studio Wiki

[giscus[bot]]

Getting Started with Seeed Studio XIAO ESP32S3 Series | Seeed Studio Wiki

Getting Started with Seeed Studio XIAO ESP32S3 Series.

https://wiki.seeedstudio.com/xiao_esp32s3_getting_started/

[Lenigan96]

I have little project and I was wondering... Is it possible to o connect the ESP3253 (Master) with the RA4M1 (slave)?

[nfs0619]

It’s definitely possible to connect the ESP32S3 (master) with the RA4M1 (slave) for communication. However, you'll likely need to design the circuit yourself to match the interfaces and communication protocols between the two. Make sure that both can properly connect and communicate.

[Lenigan96]

I'm getting this error:

Leaving...
Hard resetting with RTC WDT...

A serial exception error occurred: Cannot configure port, something went wrong. Original message: OSError(22, 'The I/O operation has been aborted because of either a thread exit or an application request.', None, 995)
Note: This error originates from pySerial. It is likely not a problem with esptool, but with the hardware connection or drivers.
For troubleshooting steps visit: https://docs.espressif.com/projects/esptool/en/latest/troubleshooting.html
Failed uploading: uploading error: exit status 1

[nfs0619]

Thanks for reaching out! We recommend contacting our technical support team at [email protected]. They will be able to provide you with more detailed guidance on your setup.

[RhymenAndy]

I get the same problem with mine. I try to upload the example Blink.ino on the ESP32S3 without success. The LED flashes afterwards, but as far as I connect an IC2 display or similar there are no functions in the other code and when uploading there is always this error.

I have tried 6 different cables. Driver reinstalled. Tried to upload via boot, all without success.

[nfs0619]

You can try entering BootLoader mode by following the steps in this guide: BootLoader Mode. This should resolve most issues with uploading code. If the problem still persists, please feel free to reach out to our technical support team at [email protected], and we’ll be happy to assist you further.

[denicolo2811]

Hello I have a porblem with the ESP32S3. I powered it form the 5V pin with the schiki Diode whats is recomented but somehow the Ouputs went crasy i unplugt it and now i can't find my ESP32S3 in the Arduino software. The 5V pin i Powert with 5V.

Can somewone help me ?

[nfs0619]

Hi! It's recommended to use the USB-C port to power the XIAO ESP32S3 for better stability.
If your board is not showing up in the Arduino IDE, try entering bootloader mode. You can follow the steps here: https://wiki.seeedstudio.com/xiao_esp32s3_getting_started/#bootloader-mode

[Dimitry1234]

Hey, can anybody help me, im trying tio get the footprint of the esp32s3 into kicad, only made it working for the esp32s3plus since there is only a kicad_mod "code" for the normal esp32s3 and not a zip file.
the code is a lil confusing and im not into it.

[nfs0619]

The files we provide for the XIAO ESP32S3 are all available in the wiki documentation. If you have any questions regarding the files, I recommend reaching out to our technical support team at [email protected].

[DharaniCreations]

Hey , can anybody help me , im trying to upload code to XIAO ESP32S3 Sense but Cannot configure port , if I connect the board to laptop it shows only the blink of red led after a while the led get's off . I have tried to BootLoader Mode but it does not work . It also gets hotter within few seconds of connection . what can I do now ?

[nfs0619]

Hi, you can try entering Bootloader mode again following this guide:
https://wiki.seeedstudio.com/xiao_esp32s3_getting_started/#bootloader-mode

If the port is still not detected, I recommend contacting Seeed technical support at [email protected]. Please provide them with details of the issue, the board’s behavior, and any relevant screenshots or videos so they can help troubleshoot further.