feat(debian): Add default root password for Armbian image

Signed-off-by: Jonas Wood <[email protected]>

Author: jonaswood01

source/devices/AM62LX/debian/Getting_Started_Guide.rst

@@ -63,6 +63,15 @@ Make sure to connect the Ethernet cable or CC33xx M.2 WiFi card, HDMI Display, M
 During first bootup, a setup script will run. This script guides the user through setting up user account, root password, date and so on.
 Once the setup ends, reboot the board. Weston screen will appear on the display.
 
+.. note::
+
+   In case you don't see the setup script during first boot, note that Armbian will automatically set the root account to its defaults:
+
+      - Username: **root**
+      - Password: **1234**
+
+   *This could happen for a number of reasons, such as power cycling the board during first boot.*
+
 .. image:: /images/debian_homescreen.png
 
 You've successfully booted Debian on |__PART_FAMILY_DEVICE_NAMES__|.

source/devices/AM62PX/debian/Getting_Started_Guide.rst

@@ -63,6 +63,15 @@ Make sure to connect the Ethernet cable or CC33xx M.2 WiFi card, HDMI Display, M
 During first bootup, a setup script will run. This script guides the user through setting up user account, root password, date and so on.
 Once the setup ends, reboot the board. Weston screen will appear on the display.
 
+.. note::
+
+   In case you don't see the setup script during first boot, note that Armbian will automatically set the root account to its defaults:
+
+      - Username: **root**
+      - Password: **1234**
+
+   *This could happen for a number of reasons, such as power cycling the board during first boot.*
+
 .. image:: /images/debian_homescreen.png
 
 You've successfully booted Debian on |__PART_FAMILY_DEVICE_NAMES__|.

source/devices/AM62X/debian/Getting_Started_Guide.rst

@@ -63,6 +63,15 @@ Make sure to connect the Ethernet cable or CC33xx M.2 WiFi card, HDMI Display, M
 During first bootup, a setup script will run. This script guides the user through setting up user account, root password, date and so on.
 Once the setup ends, reboot the board. Weston screen will appear on the display.
 
+.. note::
+
+   In case you don't see the setup script during first boot, note that Armbian will automatically set the root account to its defaults:
+
+      - Username: **root**
+      - Password: **1234**
+
+   *This could happen for a number of reasons, such as power cycling the board during first boot.*
+
 .. image:: /images/debian_homescreen.png
 
 You've successfully booted Debian on |__PART_FAMILY_DEVICE_NAMES__|.

source/devices/AM64X/debian/Getting_Started_Guide.rst

@@ -63,6 +63,15 @@ After approximately 20 seconds, the board should boot and you should see the on-
 During first bootup, a setup script will run. This script guides the user through setting up user account, root password, date and so on.
 Once the setup ends, reboot the board.
 
+.. note::
+
+   In case you don't see the setup script during first boot, note that Armbian will automatically set the root account to its defaults:
+
+      - Username: **root**
+      - Password: **1234**
+
+   *This could happen for a number of reasons, such as power cycling the board during first boot.*
+
 To verify the distro, connect via the UART console and try running ``neofetch`` on the terminal. The output of the command can be observed on the screen as shown below.
 
 .. image:: /images/debian_neofetch.png