chore(linux): Power_Management: Update URL tags to 11.0

Update any link tags to 11.00.09 if needed.

Signed-off-by: Kendall Willis <k-willis@ti.com>

Author: kwillis01

source/linux/Foundational_Components/Power_Management/pm_low_power_modes.rst

@@ -54,7 +54,7 @@ sources is found to be enabled, Partial I/O is entered instead of poweroff.
 
 The following wakeup sources have been configured for Partial I/O:
 mcu_uart0, mcu_mcan0, and mcu_mcan1. Partial I/O mode can only be tested
-when `k3-am62x-sk-lpm-wkup-sources.dtso <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-wkup-sources.dtso?h=10.01.10>`__
+when `k3-am62x-sk-lpm-wkup-sources.dtso <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-wkup-sources.dtso?h=11.00.09>`__
 overlay is loaded. Please refer to :ref:`How to enable DT overlays<howto_dt_overlays>` for more details.
 
 After Linux boots, the MCAN wakeup for Partial I/O is enabled.
@@ -132,7 +132,7 @@ I/O Only Plus DDR
    The wakeup sources that can be used to wake the system from I/O Only Plus
    DDR are mcu_uart0, mcu_mcan0, mcu_mcan1 and wkup_uart0. To use the mcu_mcan0
    and mcu_mcan1 wakeup sources, apply the
-   `k3-am62x-sk-lpm-io-ddr-wkup-sources.dtso <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-wkup-sources.dtso?h=10.01.10>`__
+   `k3-am62x-sk-lpm-io-ddr-wkup-sources.dtso <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-io-ddr-wkup-sources.dtso?h=11.00.09>`__
    overlay. Please refer to :ref:`How to enable DT overlays<howto_dt_overlays>`
    for more details. To use the mcu_uart0 and wkup_uart0 wakeup sources, direct
    register writes can be used to enable wakeup after Linux boots.

source/linux/Foundational_Components/Power_Management/pm_sw_arch.rst

@@ -151,8 +151,8 @@ Specifically, checking of constraints is done at two levels:
 
 The code enabling the constraints framework can be found in:
 
-#. TISCI PM Domain driver: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/drivers/pmdomain/ti/ti_sci_pm_domains.c?h=10.01.10
-#. TISCI driver: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/drivers/firmware/ti_sci.c?h=10.01.10
+#. TISCI PM Domain driver: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/drivers/pmdomain/ti/ti_sci_pm_domains.c?h=11.00.09
+#. TISCI driver: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/drivers/firmware/ti_sci.c?h=11.00.09
 
 Examples of adding constraints from the remote core side are being implemented and will
 be enabled in future release.
@@ -198,7 +198,7 @@ The various modes and their latencies are documented here: https://downloads.ti.
 If a device wants to put a constraint to not be powered-off, it can use the Linux
 QoS framework and set the ``DEV_PM_QOS_RESUME_LATENCY`` equal to 0.
 An example is shown in the following RemoteProc driver:
-https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/drivers/remoteproc/ti_k3_r5_remoteproc.c?h=10.01.10#n523
+https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/drivers/remoteproc/ti_k3_r5_remoteproc.c?h=11.00.09#n549
 
 .. note::
 

source/linux/Foundational_Components/Power_Management/pm_wakeup_sources.rst

@@ -271,7 +271,7 @@ by configuring the MCU GPIO controller as a wakeup source.
 In ideal scenarios, the firmware running on MCU core is responsible for configuring MCU GPIO's as a wakeup source.
 However, if the application design doesn't rely too much on the MCU firmware then
 Linux can be used to configure the MCU GPIOs as a wakeup source. You can refer to the mcu_gpio_key node in
-`k3-am62x-sk-lpm-wkup-sources.dtso <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-wkup-sources.dtso?h=10.01.10>`__
+`k3-am62x-sk-lpm-wkup-sources.dtso <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-wkup-sources.dtso?h=11.00.09>`__
 and use it as a template to configure the MCU GPIO of your choice as a wakeup capable GPIO.
 
 A brief guide to configuring an MCU GPIO as wakeup:
@@ -330,7 +330,7 @@ source and send a wakeup interrupt to the Device Manager. To understand the role
 please refer to :ref:`S/W Architecture of System Suspend<pm_sw_arch>`
 
 MCU GPIO wakeup can only be tested when
-`k3-am62x-sk-lpm-wkup-sources.dtso <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-wkup-sources.dtso?h=10.01.10>`__
+`k3-am62x-sk-lpm-wkup-sources.dtso <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-wkup-sources.dtso?h=11.00.09>`__
 overlay is loaded. Please refer to :ref:`How to enable DT overlays<howto_dt_overlays>` for more details.
 
 Once the system has entered Deep Sleep or MCU Only mode as shown in the
@@ -373,7 +373,7 @@ Main UART
 =========
 
 The way to configure UART as an I/O daisy chain wakeup, refer to the
-main_uart0 node in `k3-am62x-sk-common.dtsi <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi?h=10.01.10>`_
+main_uart0 node in `k3-am62x-sk-common.dtsi <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi?h=11.00.09>`_
 
 .. code-block:: dts
 
@@ -436,10 +436,10 @@ configuration and working of these frameworks have been covered under
 the MCU GPIO and Main UART sections.
 
 The reference configuration for Main GPIO wakeup can be found under
-gpio_key node in `k3-am62x-sk-lpm-wkup-sources.dtso <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-wkup-sources.dtso?h=10.01.10#n21>`__
+gpio_key node in `k3-am62x-sk-lpm-wkup-sources.dtso <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-wkup-sources.dtso?h=11.00.09#n21>`__
 
 Main GPIO wakeup can only be tested when
-`k3-am62x-sk-lpm-wkup-sources.dtso <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-wkup-sources.dtso?h=10.01.10>`__
+`k3-am62x-sk-lpm-wkup-sources.dtso <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-wkup-sources.dtso?h=11.00.09>`__
 overlay is loaded. Please refer to :ref:`How to enable DT overlays<howto_dt_overlays>` for more details.
 
 To use main_gpio as a wakeup source, ensure gpio is a wake-irq in /proc/interrupts:
@@ -463,7 +463,7 @@ Sleep and MCU Only modes.
 In order to use WKUP UART as a wakeup source, it needs to be configured
 in a generic way using the ti-sysc interconnect target module driver.
 The reference configuration can be found under target-module in
-`k3-am62-wakeup.dtsi <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi?h=10.01.10#n36>`__
+`k3-am62-wakeup.dtsi <https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi?h=11.00.09#n36>`__
 
 WKUP UART is generally available on the third serial port
 (/dev/ttyUSB2) and by default it only shows output from DM R5.