Commands

Commands:

Syntax for string based Interfaces. (CDC and UART):

Baudrate

• Default baudrate for UART: 115200 or 500000 (previous to 1.9)
• For CDC (USB) baudrate setting has no effect. It will send as fast as possible.

Request format:

Get: cls.(instance.)cmd? or cls.(instance.)cmd?adr

Set: cls.(instance.)cmd=val or cls.(instance.)cmd=val?adr

Info cls.(instance.)cmd! sometimes used for generating a list of supported options. Check source code for mode info.

Values can be supplied as hex (x4d2) or base 10 (1234).

Commands with 2 values are rarely used. One example is setting a register in the TMC or passing a CAN frame with a target address and value.

Reply format:

[cls.instance.cmd?|val] or [cls.instance.cmd?|val:adr] for get commands

[cls.instance.cmd=val|OK] or [cls.instance.cmd=val?adr|OK] for set commands

Some commands return strings in a custom format (Like help commands) and do not work with the HID command system.

Syntax for HID:

Structure for the vendor defined reports:

report ID: 0xA1 type(0x01 8b): {write = 0, request = 1, info = 2, writeAddr = 3, requestAddr = 4,ACK = 10, notFound = 13, notification = 14, err = 15} use write or request or info depending on the command. Write will SET an internal field to the value (Like the =val commands).

For commands that accept 2 values use writeAddr and supply value and address. The lsactive command will report a list of active classes.

• classID(0x02 16b): id of the targeted class. 0 = system, 1 = main...
• instance(0x03 8b): instance of the targeted class. Often 0 but for example there can be multiple axes or drivers.
• cmd(0x04 32b): command ID
• data(0x05 64b): the first data value to send
• addr(0x06 64b): the second data value to send

HID commands only work when the HID command interface is active and the according fields present in the HID report. This is by default the case for the FFB class but not in the failsafe fallback and other non HID classes.

Replies to request commands will reply as a request as well as any other broadcast of changed values.

Python example

import pywinusb.hid as hid
import time
import struct

# Receive and print data
def readData(data):
    if(data[0] == 0xA1):
        t = data[1]
        cls = struct.unpack('<H', bytes(data[2:4]))
        instance = data[4]
        cmd = struct.unpack('<L', bytes(data[5:9]))
        val = struct.unpack('<q', bytes(data[9:17]))
        addr = struct.unpack('<q', bytes(data[17:25]))
        print(f"Type: {t}, Class: {cls}.{instance}: cmd: {cmd}, val: {val}, addr: {addr}")


def sendCommand(report,type,cls,inst,cmd,data=0,adr=0):
    report[hid.get_full_usage_id(0xff00, 0x01)]=type # type. (0 = write, 1 = read)
    report[hid.get_full_usage_id(0xff00, 0x02)]=cls # cls (axis)
    report[hid.get_full_usage_id(0xff00, 0x03)]=inst # instance
    report[hid.get_full_usage_id(0xff00, 0x04)]=cmd # cmd (power)
    report[hid.get_full_usage_id(0xff00, 0x05)]=data # data
    report[hid.get_full_usage_id(0xff00, 0x06)]=adr # adr
    report.send()

def main():
    device = hid.HidDeviceFilter(vendor_id = 0x1209,product_id = 0xFFB0).get_devices()[0]
    device.open()

    device.set_raw_data_handler(readData)

    reports = device.find_output_reports(0xff00,0x01)
    if(reports):
        report = reports[0]
        print("Found",report)
        sendCommand(report,1,0xA01,0,0x00,0) # get power
        sendCommand(report,0,0xA01,0,0x00,1337) # set power
        sendCommand(report,1,0xA01,0,0x00,0) # get power

    while device.is_plugged():
        time.sleep(0.5)
    device.close()

if __name__ == '__main__':
    main()

Command list

Commands marked as "Debug" are treated as invalid if the sys.debug variable is not set to 1 first. They can be (even more) dangerous and possibly damage hardware if misused. That does not mean all others are safe! Commands marked as "STR" or "I" type requests are not available for HID as they return a string. Be careful when changing motor parameters. Incorrect settings can damage the hardware or cause injury.

Flag	Description	Example
R	Read or Execute	cls.cmd?
W	Write value	cls.cmd=10
RA	Read with address	cls.cmd?20
WA	Write with address	cls.cmd=10?20
I	Get special info string (Not available for HID)	cls.cmd!

System commands

Prefix	Class ID	Class description
sys.0	0x0	System Commands

Command name	CMD ID	Description	Flags
help	0x0	Print system help	(STR)
save	0x1	Write all settings to flash	R
reboot	0x2	Reset chip	R
dfu	0x3	reboot into DFU bootloader	R
lsmain	0x6	List available mainclasses	R
lsactive	0x8	List active classes (Fullname:clsname:inst:clsid:idx)	R
vint	0xE	Internal voltage(mV)	R
vext	0xF	External voltage(mV)	R
main	0x7	Query or change mainclass	R W
swver	0x4	Firmware version	R
hwtype	0x5	Hardware type	R
flashraw	0xD	Write value to flash address	WA
flashdump	0xC	Read all flash variables (val:adr)	R
errors	0xA	Read error states	R
errorsclr	0xB	Reset errors	R
heapfree	0x11	Memory info	R
format	0x9	set format=1 to erase all stored values	W
debug	0x13	Enable or disable debug commands	R W
devid	0x14	Get chip dev id and rev id	R

Note for HID: The lsactive command will report the class id in the value field and the instance number in the address field. That way it is possible to check which modules are available.

---

FFB Wheel&Joystick

Commands apply to both 1 axis and 2 axis FFB HID mainclasses

Prefix	Class ID	Class description
main.0	0x1	FFB Wheel (1 Axis): Force feedback HID game controller
main.0	0x2	FFB Joystick (2 Axis): Force feedback HID game controller

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
ffbactive	0x0	FFB status	R
btntypes	0x2	Enabled button sources	R W
addbtn	0x4	Enable button source	W
lsbtn	0x3	Get available button sources	R (STR)
aintypes	0x5	Enabled analog sources	R W
lsain	0x6	Get available analog sources	R (STR)
addain	0x7	Enable analog source	W
hidrate	0x8	Get estimated effect update speed	R
hidsendspd	0x9	Change HID gamepad update rate	R W I
estop	0xA	Emergency stop	R W

---

FFB effects

Prefix	Class ID	Class description
fx.0	0xA02	Effects: Controls internal FFB effects

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
filterCfFreq	0x0	Constant force filter frequency	R W
filterCfQ	0x1	Constant force filter Q-factor	R W
spring	0x3	Spring gain	R W I
friction	0x4	Friction gain	R W I
damper	0x5	Damper gain	R W I
inertia	0x6	Inertia gain	R W I
effects	0x2	USed effects since reset (Info print as str). set 0 to reset	R W I
effectsDetails	0x10	List effects details. set 0 to reset	R W (STR)
effectsForces	0x11	List actual effects forces.	R
damper_f	0x7	Damper biquad freq	R W
damper_q	0x8	Damper biquad q	R W
friction_f	0x9	Friction biquad freq	R W
friction_q	0xA	Friction biquad q	R W
inertia_f	0xB	Inertia biquad freq	R W
inertia_q	0xC	Inertia biquad q	R W
filterProfile_id	0xD	Conditional effects filter profile: 0 default; 1 custom	R W
frictionPctSpeedToRampup	0xE	% of max speed for gradual increase	R W

---

FFB axis

Prefix	Class ID	Class description
axis.0	0xA01	Axis: FFB axis

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
power	0x0	Overall force strength	R W
degrees	0x1	Rotation range in deg	R W
esgain	0x2	Endstop stiffness	R W
zeroenc	0x3	Zero axis	R
invert	0x4	Invert axis	R W
idlespring	0x5	Idle spring strength	R W
axisdamper	0x6	Independent damper effect	R W
enctype	0x7	Encoder type get/set/list	R W I
drvtype	0x8	Motor driver type get/set/list	R W I
pos	0x9	Encoder position	R
maxspeed	0xA	Speed limit in deg/s	R W
maxtorquerate	0xB	Torque rate limit in counts/ms	R W
fxratio	0xC	Effect ratio. Reduces effects excluding endstop. 255=100%	R W
curtorque	0xD	Axis torque	R
curpos	0xE	Axis position	R
curspd	0xF	Axis speed	R
curaccel	0x10	Axis accel	R
reduction	0x11	Encoder to axis gear reduction (val / adr) 1-256	R WA
filterProfile_id	0x14	Biquad filter profile for speed and accel	R W
filterSpeed	0x12	Biquad filter freq and q*100 for speed	R
filterAccel	0x13	Biquad filter freq and q*100 for accel	R
cpr	0x15	Reported encoder CPR	R

---

MT SPI encoder

Prefix	Class ID	Class description
mtenc.0	0x62	MT6825 SPI3

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
cs	0x0	CS pin	R W
pos	0x1	Position	R W
errors	0x2	Parity error count	R

---

BISS-C Encoder

Prefix	Class ID	Class description
bissenc.0	0x63	BISS-C

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
bits	0x0	Bits of resolution	R W
speed	0x2	SPI speed preset 1-3	R W
errors	0x3	CRC error count	R

---

SPI buttons

Prefix	Class ID	Class description
spibtn.0	0x22	SPI Buttons 1: SPI 2 Button

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
mode	0x0	SPI mode	R W I
btncut	0x1	Cut buttons right	R W
btnpol	0x2	Invert	R W
btnnum	0x3	Number of buttons	R W
cs	0x4	SPI CS pin	R W

---

Digital pin buttons

Prefix	Class ID	Class description
dpin.0	0x21	D-Pins: Digital pin button source

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
mask	0x0	Enabled pins	R W
polarity	0x1	Pin polarity	R W
pins	0x2	Available pins	R W
values	0x3	pin values	R

---

Analog shifter buttons

Supports G25,G27 (w. all SPI buttons),G29 and similar type shifters w. 2 axis analog stick and reverse button

Prefix	Class ID	Class description
shifter.0	0x23	Shifter Analog: Analog 6+1 gear shifter button source

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
mode	0x0	Shifter mode	R W I
x12	0x1	X-threshold for 1 2 gears	R W
x56	0x2	X-threshold for 5 6 gears	R W
y135	0x3	Y-threshold for 1 3 5 gears	R W
y246	0x4	Y-threshold for 2 4 6 gears	R W
revbtn	0x5	Pin for R signal	R W
cspin	0x6	CS pin for SPI modes	R W
xchan	0x7	X signal analog pin	R W
ychan	0x8	Y signal analog pin	R W
vals	0x9	Analog values	R
gear	0xA	Decoded gear	R

---

PCF8574 buttons

Prefix	Class ID	Class description
pcfbtn.0	0x24	I2C PCF8574: btnnum/8 devices required. Addresses starting at 0x20.

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
btnnum	0x0	Amount of buttons	R W
invert	0x1	Invert buttons	R W
speed	0x2	400kb/s mode	R W

---

CAN buttons

Prefix	Class ID	Class description
canbtn.0	0x25	CAN Buttons

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
btnnum	0x0	Amount of buttons	R W
invert	0x1	Invert buttons	R W
canid	0x2	CAN frame ID	R W

---

Analog pin axes

Prefix	Class ID	Class description
apin.0	0x41	AIN-Pins: Analog pins source

Command name	CMD ID	Description	Flags
filter	0xAA2	Enable lowpass filters	R W
autocal	0xAA3	Autoranging	R W
values	0xAA0	Analog output values	R
rawval	0xAA1	All raw values	R
min	0xAA4	Min value limit (adr=chan)	WA RA
max	0xAA5	Max value limit (adr=chan)	WA RA
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
mask	0x0	Enabled pins	R W
pins	0x2	Available pins	R W

---

CAN analog axes

Prefix	Class ID	Class description
cananalog.0	0x42	CAN Analog: 4 16b axes per 64b packet

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
canid	0x0	CAN frame ID of first packet. Next packet ID+1	R W
amount	0x1	Amount of analog axes	R W
maxamount	0x2	Maxmimum amount of analog axes	R

---

ADS111x analog

Prefix	Class ID	Class description
adsAnalog.0	0x43	ADS111X ADC: ADS1113/4/5 analog source

Command name	CMD ID	Description	Flags
filter	0xAA2	Enable lowpass filters	R W
autocal	0xAA3	Autoranging	R W
values	0xAA0	Analog output values	R
rawval	0xAA1	All raw values	R
min	0xAA4	Min value limit (adr=chan)	WA RA
max	0xAA5	Max value limit (adr=chan)	WA RA
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
inputs	0x0	Amount of inputs (1-4 or 1-2 if differential)	R W
diff	0x1	Differential mode (Ch0= 0p 1n Ch1= 2p 3n)	R W
gain	0x2	PGA scale (0-5)	R W I
rate	0x3	Data rate (0-7)	R W I

---

PWM motor driver

Prefix	Class ID	Class description
pwmdrv.0	0x84	PWM: PWM output motor driver

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
freq	0x1	PWM period selection	R W I
mode	0x0	PWM mode	R W I

---

TMC4671 motor driver

Prefix	Class ID	Class description
tmc.0	0x81	TMC4671: TMC4671 interface

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
cpr	0x0	CPR in TMC	R W
mtype	0x1	Motor type	R W I
encsrc	0x2	Encoder source	R W I
tmcHwType	0x3	Version of TMC board	R W I
encalign	0x4	Align encoder	R
poles	0x5	Motor pole pairs	R W
acttrq	0x6	Measure torque and flux	R
pwmlim	0x7	PWM limit	R W (DEBUG)
torqueP	0x8	Torque P	R W
torqueI	0x9	Torque I	R W
fluxP	0xA	Flux P	R W
fluxI	0xB	Flux I	R W
velocityP	0xC	Velocity P	R W
velocityI	0xD	Velocity I	R W
posP	0xE	Pos P	R W
posI	0xF	Pos I	R W
tmctype	0x10	Version of TMC chip	R
pidPrec	0x11	PID precision bit0=I bit1=P. 0=Q8.8 1= Q4.12	R W
phiesrc	0x12	PhiE source	R W (DEBUG)
fluxoffset	0x13	Offset flux scale for field weakening	R W
seqpi	0x14	Sequential PI	R W
iScale	0x15	Counts per A	(STR)
encdir	0x16	Encoder dir	R W (DEBUG)
abnpol	0x1F	Encoder polarity	R W
temp	0x17	Temperature in C * 100	R
reg	0x18	Read or write a TMC register at adr	WA RA (DEBUG)
svpwm	0x19	Space-vector PWM	R W
autohome	0x1D	Find abn index	R
abnindex	0x1C	Enable ABN index	R W
calibrate	0x1A	Full calibration	R
calibrated	0x1B	Calibration valid	R
state	0x1E	Get state	R
combineEncoder	0x20	Use TMC for movement. External encoder for position	R W
invertForce	0x21	Invert incoming forces	R W
vm	0x22	VM in mV	R
extphie	0x23	external phie	R

---

ODrive motor driver (CAN)

Example here is only M0. M1 is available too.

Prefix	Class ID	Class description
odrv.0	0x85	ODrive (M0): ODrive motor driver with CAN

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
canid	0x0	CAN id of ODrive	R W
canspd	0x1	CAN baudrate	R W
errors	0x2	ODrive error flags	R
state	0x3	ODrive state	R
maxtorque	0x4	Max torque to send for scaling	R W
vbus	0x5	ODrive Vbus	R
anticogging	0x6	Set 1 to start anticogging calibration	W
connected	0x7	ODrive connection state	R

---

VESC motor driver

Prefix	Class ID	Class description
vesc.0	0x87	VESC: VESC CAN interface

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
offbcanid	0x0	CAN id of OpenFFBoard Axis	R W
vesccanid	0x1	CAN id of VESC	R W
canspd	0x2	CAN baud (3=250k 4=500k 5=1M)	R W
errorflags	0x3	VESC error state	R
vescstate	0x4	VESC state	R
voltage	0x5	VESC supply voltage (mV)	R
encrate	0x6	Encoder update rate	R
pos	0x7	VESC position	R
torque	0x8	Current VESC torque	R
forceposread	0x9	Force a position update	R
useencoder	0xA	Enable VESC encoder	R W
offset	0xB	Get or set encoder offset	R W

---

Ports

CAN port

Prefix	Class ID	Class description
can.0	0xC01	Can port

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
speed	0x0	CAN speed preset (0:50k;1:100k;2:125k;3:250k;4:500k;5:1M)	R W I
send	0x1	Send CAN frame. Adr&Value required	WA

---

I²C port

Prefix	Class ID	Class description
i2c.0	0xC02	I2C port

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
speed	0x0	I2C speed preset (0:100k;1:400k)	R W I

---

Other mainclasses:

CAN bridge

Prefix	Class ID	Class description
main.0	0x1	CAN Bridge (This class is GVRET/SavvyCAN compatible!)

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
can	0x0	Send a frame or get last received frame	R WA
rtr	0x1	Send a RTR frame	WA R
spd	0x2	Change or get CAN baud	R W

---

TMC debug bridge

Debug mode must be active for this to show up

Prefix	Class ID	Class description
main.0	0x1	TMC Debug Bridge: Compatible with TMCL-IDE.

To use the FOC modes position; velocity and torque you first must manually select the encoder and wait for alignment.

Command name	CMD ID	Description
id	0x80000001	ID of class
name	0x80000002	name of class
help	0x80000003	Prints help for commands
cmduid	0x80000005	Command handler index
instance	0x80000004	Command handler instance number
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid
torque	0x0	Change torque and enter torque mode
pos	0x1	Change pos and enter pos mode
openloopspeed	0x2	Move openloop. adr=strength;val=speed
velocity	0x3	Change velocity and enter velocity mode
mode	0x4	Change motion mode

---

MIDI

Debug mode must be active for this to show up

Prefix	Class ID	Class description
main.0	0x1	MIDI (TMC): Easteregg mainclass to play midi songs on the tmc

Command name	CMD ID	Description	Flags
id	0x80000001	ID of class	R
name	0x80000002	name of class	R (STR)
help	0x80000003	Prints help for commands	R I (STR)
cmduid	0x80000005	Command handler index	R
instance	0x80000004	Command handler instance number	R
cmdinfo	0x80000007	Flags of a command id (adr). -1 if cmd id invalid	RA
power	0x0	Intensity	R W
range	0x1	Range of phase change	R W