Use safe clock freqs for AnalogOut; use DAC REFRESH on SAMD51.

Author: dhalbert

ports/atmel-samd/asf4_conf/samd21/hpl_gclk_config.h

@@ -1,12 +1,13 @@
 // Circuit Python SAMD21 clock tree:
-// DFLL48M (with USBCRM on to sync with external USB ref) -> GCLK0
+// DFLL48M (with USBCRM on to sync with external USB ref) -> GCLK0, GCLK1
 //   GCLK0 (48MHz) -> peripherals
+//   GLCK1 (48MHz divided by 150 = 320Khz) -> DAC peripheral (DAC requires 350KHz or lower)
 
 // We'd like to use XOSC32K as a ref for DFLL48M on boards with a 32kHz crystal,
 // but haven't figured that out yet.
 
 // Used in hpl/core/hpl_init.c to define which clocks should be initialized first.
-#define CIRCUITPY_GCLK_INIT_1ST (1 << 0)
+#define CIRCUITPY_GCLK_INIT_1ST (1 << 0 | 1 << 1)
 
 
 /* Auto-generated config file hpl_gclk_config.h */
@@ -127,7 +128,7 @@
 // <i> Indicates whether Output Enable is enabled or not
 // <id> gclk_arch_gen_1_oe
 #ifndef CONF_GCLK_GEN_1_OE
-#define CONF_GCLK_GEN_1_OE 0
+#define CONF_GCLK_GEN_1_OE 1
 #endif
 
 // <q> Output Off Value
@@ -172,7 +173,7 @@
 // <i> This defines the clock source for generic clock generator 1
 // <id> gclk_gen_1_oscillator
 #ifndef CONF_GCLK_GEN_1_SRC
-#define CONF_GCLK_GEN_1_SRC GCLK_GENCTRL_SRC_XOSC32K
+#define CONF_GCLK_GEN_1_SRC GCLK_GENCTRL_SRC_DFLL48M
 #endif
 // </h>
 
@@ -181,7 +182,7 @@
 // <i>
 // <id> gclk_gen_1_div
 #ifndef CONF_GCLK_GEN_1_DIV
-#define CONF_GCLK_GEN_1_DIV 1
+#define CONF_GCLK_GEN_1_DIV 150
 #endif
 
 // </h>

ports/atmel-samd/asf4_conf/samd21/peripheral_clk_config.h

@@ -385,15 +385,15 @@
 
 // <i> Select the clock source for DAC.
 #ifndef CONF_GCLK_DAC_SRC
-#define CONF_GCLK_DAC_SRC GCLK_CLKCTRL_GEN_GCLK0_Val
+#define CONF_GCLK_DAC_SRC GCLK_CLKCTRL_GEN_GCLK1_Val
 #endif
 
 /**
  * \def CONF_GCLK_DAC_FREQUENCY
  * \brief DAC's Clock frequency
  */
 #ifndef CONF_GCLK_DAC_FREQUENCY
-#define CONF_GCLK_DAC_FREQUENCY 48000000
+#define CONF_GCLK_DAC_FREQUENCY 320000
 #endif
 
 // <y> USB Clock Source

ports/atmel-samd/asf4_conf/samd51/hpl_dac_config.h

@@ -72,7 +72,7 @@
 // <i> This defines the refresh period. If it is 0, the refresh mode is disabled, else the refresh period is: value * 500us
 // <id> dac0_arch_refresh
 #ifndef CONF_DAC0_REFRESH
-#define CONF_DAC0_REFRESH 0
+#define CONF_DAC0_REFRESH 2
 #endif
 // </h>
 // <h> Channel 1 configuration
@@ -111,7 +111,7 @@
 // <i> This defines the refresh period. If it is 0, the refresh mode is disabled, else the refresh period is: value * 500us
 // <id> dac1_arch_refresh
 #ifndef CONF_DAC1_REFRESH
-#define CONF_DAC1_REFRESH 0
+#define CONF_DAC1_REFRESH 2
 #endif
 // </h>
 

ports/atmel-samd/asf4_conf/samd51/hpl_gclk_config.h

@@ -1,7 +1,7 @@
 // Circuit Python SAMD51 clock tree:
 // DFLL48M (with USBCRM on to sync with external USB ref) -> GCLK1, GCLK5
-//   GCLK1 (48MHz) -> peripherals
-//   GCLK5 (divided down to 2 MHz) -> DPLL0
+//   GCLK1 (48MHz) -> 48 MHz peripherals
+//   GCLK5 (48 MHz divided down to 2 MHz) -> DPLL0, DAC peripherals
 //     DPLL0 (multiplied up to 120 MHz) -> GCLK0, GCLK4 (output for monitoring)
 
 // We'd like to use XOSC32K as a ref for DFLL48M on boards with a 32kHz crystal,

ports/atmel-samd/asf4_conf/samd51/peripheral_clk_config.h

@@ -73,15 +73,15 @@
 // <id> dac_gclk_selection
 // <i> Select the clock source for DAC.
 #ifndef CONF_GCLK_DAC_SRC
-#define CONF_GCLK_DAC_SRC GCLK_PCHCTRL_GEN_GCLK1_Val
+#define CONF_GCLK_DAC_SRC GCLK_PCHCTRL_GEN_GCLK5_Val
 #endif
 
 /**
  * \def CONF_GCLK_DAC_FREQUENCY
  * \brief DAC's Clock frequency
  */
 #ifndef CONF_GCLK_DAC_FREQUENCY
-#define CONF_GCLK_DAC_FREQUENCY 48000000
+#define CONF_GCLK_DAC_FREQUENCY 2000000
 #endif
 
 // <y> EVSYS Channel 0 Clock Source

ports/atmel-samd/common-hal/analogio/AnalogOut.c

@@ -65,12 +65,14 @@ void common_hal_analogio_analogout_construct(analogio_analogout_obj_t* self,
 
     #ifdef SAMD51
     hri_mclk_set_APBDMASK_DAC_bit(MCLK);
+    // This clock should be <= 12 MHz, per datasheet section 47.6.3.
     hri_gclk_write_PCHCTRL_reg(GCLK, DAC_GCLK_ID, GCLK_PCHCTRL_GEN_GCLK5_Val | (1 << GCLK_PCHCTRL_CHEN_Pos));
     #endif
 
     #ifdef SAMD21
     _pm_enable_bus_clock(PM_BUS_APBC, DAC);
-    _gclk_enable_channel(DAC_GCLK_ID, GCLK_CLKCTRL_GEN_GCLK0_Val);
+    // This clock should be <= 350kHz, per datasheet table 37-6. 
+    _gclk_enable_channel(DAC_GCLK_ID, GCLK_CLKCTRL_GEN_GCLK1_Val);
     #endif
 
     // Don't double init the DAC on the SAMD51 when both outputs are in use. We use the free state
@@ -123,7 +125,7 @@ void common_hal_analogio_analogout_deinit(analogio_analogout_obj_t *self) {
 
 void common_hal_analogio_analogout_set_value(analogio_analogout_obj_t *self,
         uint16_t value) {
-    // Input is 16 bit so make sure and set LEFTADJ to 1 to it takes the top
+    // Input is 16 bit so make sure and set LEFTADJ to 1 so it takes the top
     // bits. This is currently done in asf4_conf/*/hpl_dac_config.h.
     dac_sync_write(&self->descriptor, self->channel, &value, 1);
 }