Skip to content

GoodPracticesToUseKafkaProducer.md

Latest commit

 

History

History
76 lines (38 loc) · 4.11 KB

GoodPracticesToUseKafkaProducer.md

File metadata and controls

76 lines (38 loc) · 4.11 KB

Good Practices to Use a KafkaProducer

If we want to achieve high performance/availability, here're some rules of thumb.

Use a KafkaAsyncProducer for better throughput

You should not use a KafkaSyncProducer if you want to get a high throughput. The Sync means the send operation is a synchronous operation, and would not go on until the acks are received.

The message.max.bytes must be consistent with Kafka servers' setting

  • Default value: 1000,000

  • The default setting for brokers is message.max.bytes = 1000012, and do MAKE SURE the client side setting no larger than it. Otherwise, it might construct a MessageSet which would be rejected (error: INVALID_MESSAGE_SIZE) by brokers.

In most cases, the default value for linger.ms is good enough

  • It means the delay in milliseconds to wait for messages in the producer queue to accumulate before constructing MessageSets to transmit to brokers.

    1. For a KafkaSyncProducer, it sends the messages one by one (after acks response received), thus it could use linger.ms=0 (as default) to eliminate the unnecessary waiting time.

    2. For a KafkaAsyncProduer, a larger linger.ms could be used to accumulate messages for MessageSets to improve the performance -- it should be the result of balancing between throughput and latency.

Calculate batch.num.messages with the average message size

  • Default value: 10,000

  • It defines the maximum number of messages batched in one MessageSet.

    Normally, larger value, better performance. However, since the size of MessageSet is limited by message.max.bytes, a too large value would not help any more.

    E.g, with the default message.max.bytes=1000000 and batch.num.messages=10000 settings, you could get the best performance while the average message size is larger than 100 bytes.

    However, if the average message size is small, you have to enlarge it (to message.max.bytes/average_message_size at least).

Choose acks wisely

  • The acks parameter controls how many partition replicas must receive the record before the producer can consider the write successful.

    • acks=0, the producer will not wait for a reply from the broker before assuming the message was sent successfully.

    • acks=1, the producer will receive a success response from the broker the moment the leader replica received the message.

    • acks=all, the producer will receive a success response from the broker once all in-sync replicas received the message.

    • Note: if "ack=all", please make sure the topic's replication factor is larger than 1.

  • The acks=all setting will highly impact the throughput & latency, and it would be obvious if the traffic latency between kafka brokers is high. But it's mandatory if we want to achieve high availability.

Determine the default sending buffer (according to the latency)

  • Default queue.buffing setting,

    • queue.buffering.max.messages=1000000

    • queue.buffering.max.kbytes=0x100000 (1GB)

  • Normally, the default settings should be good enough.

How could a message miss after send?

  • The message might even not have been received by the partition leader! (with acks=0)

  • Once the message received by the partition leader, the leader crashed just after responding to the producer, but has no chance to synchronize the message to other replicas. (with acks=1)

  • Once the message received by the partition leader, the leader crashed just after responding to the producer, but with no in-sync replica to synchronize for the message. (with acks=all, while brokers are with min.insync.replicas=1)

How does message disordering happen? How to avoid it?

  • Take an example, -- a KafkaAsyncProducer just sent many messages, and a few of these messages (in the middle) failed to be delivered successfully. While the producer got the sending error, it might retry sending these messages again, thus causing the disordering.

  • To avoid it. Two options,

    • Use a KafkaSyncProducer, but this would severely impact the throughput.

    • Embed some sequence number (e.g, record id, part of the key, etc) in the ProducerRecord, for de-duplication.