solutions: ref-designs: Added CN0566 page and subpages

Signed-off-by: Joyce Velasco <[email protected]>

Author: jvelasc2

docs/solutions/reference-designs/eval-cn0566-rpiz/assy-prod-test/camera_mount.jpg

@@ -0,0 +1,90 @@
+.. _cn0566_assy_prod_test:
+
+CN0566 Assembly and Production Test
+===================================
+
+Assembly and Production Test Procedure for CN0566 (ADALM-PHASER)
+
+.. video:: https://youtu.be/WR1DHfraLf8
+
+Assembly
+--------
+
+1. Install the u.fl cables as shown. Ensure that the connector is aligned
+   before seating, and use a flat surface to press, such as an unused pencil
+   eraser: 
+   
+   .. figure:: u_fl_cables.jpg
+    :width: 600 px
+
+2. Install the 40-pin M-F extender on the reverse side of the board. Place the
+   board on stiff antistatic foam while doing this, and use a steady, even
+   pressure. 
+
+   .. figure:: rpi_riser.jpg
+    :width: 600 px
+ 
+3. Install a 22mm M-F standoff and 12mm M-F standoff as shown below. The
+   threads from the 22mm standoff enter from the reverse side of the board.
+
+  .. figure:: standoff_stackup.png
+
+4. Install the camera mount using two 3mm pan head screws as shown. Do not over-tighten.
+
+  .. figure:: camera_mount.jpg
+
+5. Install the four tall standoffs from the top side of the board, at the four
+   corners. 
+
+6. Prepare the ADALM-PLUTO:
+
+    - Remove the board from the enclosure, leaving the SMA panel intact
+    - Solder the 14-pin header as noted.
+
+  .. figure:: pluto_prep.jpg
+
+7. Mount the ADALM-Pluto from the top side of the board. Note that the
+   threaded ends of the standoff will need to be flexed slightly. Secure with 4x
+   M2.5 nylon nuts.
+
+8. Connect the U.FL cables to the ADALM-PLUTO as shown:
+
+    - The previously installed RX2 cable from the CN0566 board to Pluto RX2A
+    - Snap the second cable onto the SMA to U.FL adapter.
+    - Snap the other end of the second cable onto Pluto TX2A, then snake the
+      adapter between the Pluto and CN0566, thread onto CN0566 TX_IN SMA.
+    - Install a 90-degree SMA adapter onto CN0566 J1 as shown, facing downward.
+
+  .. figure:: pluto_u_fls.jpg
+
+
+9. Connect the 14-pin ribbon cable between CN0566 and Pluto as shown:
+
+  .. figure:: ribbon_cable_installation.jpg
+
+10. Mount the Raspberry Pi from the reverse side of the board. Use 4x M2.5 x 4mm pan head screws to secure.
+
+Test
+----
+
+- Place the Vivaldi antenna / Selfie-Stick directly above the assembly as shown.
+  The antenna should aim directly down at the center of the array.
+- Plug a micro HDMI to HDMI cable into the Raspberry Pi HDMI connector closest
+  to the USB-C power input.
+- Insert a pre-prepared SD card into the Raspberry Pi. (See below for
+  preparation instructions).
+- Plug a keyboard into one of the remaining USB ports on the Raspberry Pi 
+  (A mouse is optional).
+- Connect a 3 amp USB-C power adapter to the power input on the CN0566. The
+  Raspberry Pi will boot.
+- Create an SD card by following the instructions here:
+  :ref:`quickstart <cn0566_quickstart>`
+- Type the following command:
+
+  ::
+
+    cd ~/pyadi-iio/examples/phaser
+    python3 phaser_prod_tst.py
+
+- Then press enter. The test script will automatically run and print pass/fail
+  results.