Analog Audio Input Options
Below are a number of popular Arduino compatible microphones that have been tested.
| Model | Compatibility | Notes |
|---|---|---|
| INMP401 | Good | Some Chinese ones are not reliable. |
| MAX4466 | Good | No problems found. |
| MAX9812 | Good | Only 20dB gain, but worked OK. |
| MAX9814 | Good | Best to set the gain to 40dB. |
If you are using the MAX9814, you need to connect gain to vdd to set the gain to 40dB as the default 60db has far too much background noise. The inexpensive sound sensors you can buy from Aliexpress or elsewhere (such as LM393 or KY-038) typically have a digital output and may or may not work adequately. For more information on our microphone test results, see our Arduino Compatible Microphones document.
If the LED's are active when the ambient volume is low while running volume only effects beginning with a single '*', you can increase the background noise filtering (or squelch) by navigating to the 'Config | LED Preferences | Sound' and increase the Squelch value. You can also make it more sensitive by lowering that Squelch value. In addition, there is a gain setting, which is required for the much lower signal level provided by the line-in configuration. We have not yet implemented a similar capability for the FFT effects.
Note 1: Do NOT connect input devices to 5V (or Vin). The power should be connected to the 3.3V pin.
Note 2: A piezo vibration sensor (from aliexpress) was successfully hooked up and tested.
Note 3: On the ESP32, the ADC pin used is pin 36 (also known as VP), while the ESP8266 uses A0.
Note 4: On the ESP32, the ADC and I2S pins are defined in audio_reactive.h.
The following schematics are provided as an example only. There are many ways to achieve the same results. These are only a few of those ways.
| Microphone Wiring Example (MAX9814) | Line In Wiring Example |
|---|---|
 |
 |
Some folks have mentioned that they don't need this circuit, which is fine. Here's an explanation of that circuit.
The 680 ohm resistors provide termination so that you don't get reflection on the incoming signals. The 100nf capacitors remove any DC offset from the incoming signal. Remember that the ESP goes from 0V to 3.3V. Beyond that lay dragons. Finally, the 1M resistors provide DC centering of the incoming (now) AC only signal halfway between 0 and 3.3V.
Note 1: If you are just using a single L or R channel for the line-in, disconnect the capacitor for the other channel, or the resultant sample will be significantly reduced in amplitude.
Note 2: Providing a 'T' connector so that you can hear the music as it goes into the circuit is highly recommended. In the author's case, there was considerable static when the ESP32 was powered by the computer's USB port, but was fine when the ESP32 was powered by a USB powerbank.
The following diagram shows one way of connecting a 3.5mm jack and an analog microphone to the ESP8266/32 while being able to change your desired input with a simple SPDT switch.
The left and right channels of the TRS Jack are connected together to sample both channels simultaneously as one channel.
Connect the output of the capacitor to the ADC pin for your board.
On the ESP32, the ADC pin used is pin 36 (also known as VP), while the ESP8266 uses A0. Power is connected to the 3.3V pin. These pins are defined in wled00/audio_reactive.h.
The volume reactive routines (starting with a single *), support a squelch or background noise suppression. This can be configured near the bottom of the LED Settings page.
Line-in signals are typically much lower than that of some of the microphones. Rather than use an auto gain function, you can manually adjust the gain from 0 to 255, which translate to a 1.0 gain up to a 5.0 gain for the volume reactive routines (only).
We've often seen spikes when using an analog microphone in conjunction with WLED. There's an article that should shed light on the issue at ESP32 microcontroller generates noise on microphone.