HyperHDR with HyperSPI wiht Adafruit Scorpio rp2040

[edoedo]

Hi,
I'm tring to get my HyperHDR installed on Raspberry Pi4 to work with my Adafruit Scorpio rp2040.
It is working with HyperSerialPico, so my leds are correct installed.
Also with an ownbuild setup with github because of the 2 segments setup

This is my CMakeLists.txt: (for HyperSerialPico):

set(CMAKE_SYSTEM_NAME Generic)
# User configuration section starts here and ends a bit further

# Some boards, such as the first Adafruit revisions, may have trouble booting properly
# due to bad componets used in the design.
# Turn this setting to ON if your rp2040 is not detected after firmware upload and reset
set(BOOT_WORKAROUND ON)

# Default output data pin for the non-SPI LED strips (only for sk6812/ws2812b)
set(OUTPUT_DATA_PIN 16)

# Use multi-segment, starting index of second led strip or OFF to disable
set(SECOND_SEGMENT_INDEX 175)

# If multi-segment is used and it's reversed, set this option to ON to enable reversing
set(SECOND_SEGMENT_REVERSED ON)

# HyperSPI communication interface with Raspberry Pi
set(OUTPUT_SPI_DATA_PIN 4)
set(OUTPUT_SPI_CLOCK_PIN 2)
set(OUTPUT_SPI_CHIP_SELECT 5)
set(OUTPUT_SPI_INTERFACE spi0)

# User configuration section ends here
# Usually you don't need to change anything below this section

if(NOT CMAKE_HOST_WIN32)
	string(ASCII 27 EscChar)
	set(ColorReset  "${EscChar}[m")
	set(GreenColor  "${EscChar}[32m")
	set(YellowColor "${EscChar}[33m")	
endif()

if (OVERRIDE_DATA_PIN)
	set(OUTPUT_DATA_PIN ${OVERRIDE_DATA_PIN})
	message( STATUS "${YellowColor}Overriding output Neopixel Data GPIO: ${OUTPUT_DATA_PIN}${ColorReset}")
endif()

if (OVERRIDE_SPI_DATA_PIN)
	set(OUTPUT_SPI_DATA_PIN ${OVERRIDE_SPI_DATA_PIN})
	message( STATUS "${YellowColor}Overriding input SPI Data GPIO: ${OUTPUT_SPI_DATA_PIN}${ColorReset}")
endif()

if (OVERRIDE_SPI_CLOCK_PIN)
	set(OUTPUT_SPI_CLOCK_PIN ${OVERRIDE_SPI_CLOCK_PIN})
	message( STATUS "${YellowColor}Overriding input SPI Clock GPIO: ${OUTPUT_SPI_CLOCK_PIN}${ColorReset}")
endif()

if (OVERRIDE_SPI_CHIP_SELECT)
	set(OUTPUT_SPI_CHIP_SELECT ${OVERRIDE_SPI_CHIP_SELECT})
	message( STATUS "${YellowColor}Overriding input SPI chip select GPIO: ${OUTPUT_SPI_CHIP_SELECT}${ColorReset}")
endif()

if (OVERRIDE_SPI_INTERFACE)
	set(OUTPUT_SPI_INTERFACE ${OVERRIDE_SPI_INTERFACE})
	message( STATUS "${YellowColor}Overriding input SPI Interface: ${OUTPUT_SPI_INTERFACE}${ColorReset}")
endif()

cmake_minimum_required(VERSION 3.13)

set(PICO_SDK_PATH ${CMAKE_CURRENT_SOURCE_DIR}/HyperSerialPico/sdk/pico)
set(FREERTOS_KERNEL_PATH ${CMAKE_CURRENT_SOURCE_DIR}/HyperSerialPico/sdk/freertos)
include(${PICO_SDK_PATH}/external/pico_sdk_import.cmake)
include(${FREERTOS_KERNEL_PATH}/portable/ThirdParty/GCC/RP2040/FreeRTOS_Kernel_import.cmake)

project(HyperSPI_Pico C CXX ASM)
pico_sdk_init()

set(PICO_PROGRAM_MAIN_ENTRY "../hyperspi.cpp")
set(DISABLE_SPI_LEDS ON)
add_definitions(-DSPI_INTERFACE=${OUTPUT_SPI_INTERFACE}
				-DSPI_DATA_PIN=${OUTPUT_SPI_DATA_PIN}
				-DSPI_CLOCK_PIN=${OUTPUT_SPI_CLOCK_PIN}
				-DSPI_CHIP_SELECT=${OUTPUT_SPI_CHIP_SELECT})
add_subdirectory(HyperSerialPico) 

So i think i did every thing correct

It all is wirred like:

Settings of HyperHDR:

The log output of HyperHDR:

2025-06-24T22:19:50.244Z [CORE] TTY is not attached to the log output
2025-06-24T22:19:50.262Z [MAIN] Database path: '/home/edo/.hyperhdr/db/hyperhdr.db', readonlyMode = disabled
2025-06-24T22:19:50.262Z [MAIN] Starting HyperHdr - 21.0.0.0, (HEAD detached at v21.0.0.0) (Awawa-24e1675/803162c-1741515688), built: Mar  9 2025:10:34:19
2025-06-24T22:19:50.262Z [MAIN] Set user data path to '/home/edo/.hyperhdr'
2025-06-24T22:19:50.262Z [INSTANCE_CFG] Loading instance configuration
2025-06-24T22:19:50.263Z [DB] Database opened: /home/edo/.hyperhdr/db/hyperhdr.db
2025-06-24T22:19:50.318Z [INSTANCE_CFG] Settings database initialized
2025-06-24T22:19:50.343Z [SOUND_GRABBER] Sound device is disabled
2025-06-24T22:19:50.415Z [JSONSERVER] (JsonServer.cpp:26) Created new instance
2025-06-24T22:19:50.415Z [JSONSERVER] Started on port 19444
2025-06-24T22:19:50.416Z [SSDP] (SSDPHandler.cpp:31) SSDPHandler is initialized
2025-06-24T22:19:50.380Z [V4L2:USB3.0 UHD: US] (GrabberWrapper.cpp:53) Starting the grabber wrapper
2025-06-24T22:19:50.380Z [V4L2:USB3.0 UHD: US] Found capture device: /dev/video15
2025-06-24T22:19:50.381Z [V4L2:USB3.0 UHD: US] Found capture device: /dev/video21
2025-06-24T22:19:50.381Z [V4L2:USB3.0 UHD: US] Found capture device: /dev/video14
2025-06-24T22:19:50.381Z [V4L2:USB3.0 UHD: US] Found capture device: /dev/video22
2025-06-24T22:19:50.382Z [V4L2:USB3.0 UHD: US] Found capture device: /dev/video0
2025-06-24T22:19:50.390Z [X11_SYSTEM:AUTO] Loaded X11 proxy library for screen capturing
2025-06-24T22:19:50.390Z [DAEMON] The system doesn't support the X11 system grabber
2025-06-24T22:19:50.390Z [HYPERHDR0] Starting the instance
2025-06-24T22:19:50.390Z [INSTANCE_CFG0] Loading instance configuration
2025-06-24T22:19:50.390Z [DAEMON] The system doesn't support the framebuffer system grabber
2025-06-24T22:19:50.391Z [DB] Database opened: /home/edo/.hyperhdr/db/hyperhdr.db
2025-06-24T22:19:50.391Z [X11_SYSTEM:auto] (SystemWrapper.cpp:70) Closing grabber: X11_SYSTEM:auto
2025-06-24T22:19:50.391Z [FRAMEBUF_SYSTEM:auto] (SystemWrapper.cpp:70) Closing grabber: FRAMEBUF_SYSTEM:auto
2025-06-24T22:19:50.393Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:425) Device has 'brightness' control => min: 0, max: 100, default: 50
2025-06-24T22:19:50.406Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:431) Device has 'contrast' control => min: 0, max: 100, default: 50
2025-06-24T22:19:50.419Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:437) Device has 'saturation' control => min: 0, max: 100, default: 50
2025-06-24T22:19:50.432Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:443) Device has 'hue' control => min: 0, max: 100, default: 50
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1920 x 1080 @ 60 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1920 x 1080 @ 50 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1920 x 1080 @ 30 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1920 x 1080 @ 20 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1920 x 1080 @ 10 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1600 x 1200 @ 60 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1600 x 1200 @ 50 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1600 x 1200 @ 30 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1600 x 1200 @ 20 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1600 x 1200 @ 10 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1360 x 768 @ 60 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1360 x 768 @ 50 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1360 x 768 @ 30 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1360 x 768 @ 20 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1360 x 768 @ 10 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 1024 @ 60 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 1024 @ 50 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 1024 @ 30 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 1024 @ 20 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 1024 @ 10 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 960 @ 60 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 960 @ 50 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 960 @ 30 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 960 @ 20 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 960 @ 10 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 720 @ 60 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 720 @ 50 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 720 @ 30 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 720 @ 20 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 720 @ 10 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1024 x 768 @ 60 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1024 x 768 @ 50 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1024 x 768 @ 30 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1024 x 768 @ 20 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1024 x 768 @ 10 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 800 x 600 @ 60 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 800 x 600 @ 50 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 800 x 600 @ 30 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 800 x 600 @ 20 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 800 x 600 @ 10 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 720 x 576 @ 60 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 720 x 576 @ 50 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 720 x 576 @ 30 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 720 x 576 @ 20 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 720 x 576 @ 10 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 720 x 480 @ 60 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 720 x 480 @ 50 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 720 x 480 @ 30 fps yuyv input 0
2025-06-24T22:19:50.433Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 720 x 480 @ 20 fps yuyv input 0
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 720 x 480 @ 10 fps yuyv input 0
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 640 x 480 @ 60 fps yuyv input 0
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 640 x 480 @ 50 fps yuyv input 0
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 640 x 480 @ 30 fps yuyv input 0
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 640 x 480 @ 20 fps yuyv input 0
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 640 x 480 @ 10 fps yuyv input 0
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:102) P010 was supported on the build machine
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] Restarting video grabber is now blocked due to reloading of the configuration
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] Cropping image: width=0 height=0; crop: left=0 right=0 top=0 bottom=0 
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] (GrabberWrapper.cpp:180) CEC keycode. Start: 0, stop: 0
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] (Grabber.cpp:276) Set new width: 1280, height: 1024 for capture
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] (Grabber.cpp:452) setWidthHeight preparing to restarting video grabber 0
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] Delayed restart of the grabber due to change of the capturing resolution
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] Delayed restart of the grabber due to change of the framerate
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] (Grabber.cpp:390) setBrightnessContrastSaturationHue nothing changed
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:143) setHdrToneMappingMode to: Disabled
2025-06-24T22:19:50.434Z [AUTOTONEMAPPING] Tone mapping is currently: disabled
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] (Grabber.cpp:299) setFpsSoftwareDecimation to: 1
2025-06-24T22:19:50.434Z [SIGNAL_OLD] (DetectionManual.cpp:84) Signal detection area set to: 0.250000,0.250000 x 0.750000,0.750000
2025-06-24T22:19:50.434Z [SIGNAL_OLD] (DetectionManual.cpp:74) Signal threshold set to: {0, 0, 0} and frames: 50
2025-06-24T22:19:50.434Z [SIGNAL_AUTO] (DetectionAutomatic.cpp:375) Automatic signal detection -> errorTolerance: 9, modelTolerance: 90, sleepTime: 1000, wakeTime: 0
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] (Grabber.cpp:497) setDeviceVideoStandard preparing to restart video grabber. Old: '' new: 'USB3.0 UHD: USB3.0 UHD (video0)'
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] Delayed restart of the grabber due to change of selected device
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] (Grabber.cpp:317) Force encoding to: yuyv (old: NO_CHANGE)
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] Delayed restart of the grabber due to change of the video encoding format
2025-06-24T22:19:50.434Z [V4L2:USB3.0 UHD: US] setQFrameDecimation is now: enabled
2025-06-24T22:19:50.436Z [AUTOTONEMAPPING] Enabled: no, time to enable: 30s, time to disable: 500ms, thresholds: { 155, 175, 160}
2025-06-24T22:19:50.472Z [INSTANCE_CFG0] Settings database initialized
2025-06-24T22:19:50.472Z [COMPONENTCTRL0] (ComponentController.cpp:27) ComponentController is initialized. Components are ENABLED
2025-06-24T22:19:50.475Z [MUXER0] (Muxer.cpp:54) Muxer initialized
2025-06-24T22:19:50.475Z [BLACKBORDER] Set mode to: osd
2025-06-24T22:19:50.475Z [COMPONENTCTRL0] Blackborder detector: enabled
2025-06-24T22:19:50.476Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:192) Set LED mapping type to advanced
2025-06-24T22:19:50.476Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:176) setSparseProcessing to 0
2025-06-24T22:19:50.476Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:103) ImageToLedManager initialized
2025-06-24T22:19:50.476Z [COLORSPACE_CALIBRATION0] classicMode: no, gammas:[3.00, 3.00, 3.00], saturation: 1.00, luminance: 1.00, backLight: [enabled, threshold: 0, colored: no]
2025-06-24T22:19:50.476Z [LED_CALIBRATION0] (LedCalibration.cpp:101) Calibration config '0' for LED segment: [0, 313]
2025-06-24T22:19:50.478Z [HYPERHDR0] Led strip RGB order is: rgb
2025-06-24T22:19:50.479Z [SMOOTHING0] High resolution clock is NOT STEADY!
2025-06-24T22:19:50.479Z [SMOOTHING0] Creating config (0) => type: Alternative, pause: false, settlingTime: 25ms, interval: 17ms (58Hz), antiFlickTres: 0, antiFlickStep: 0, antiFlickTime: 0
2025-06-24T22:19:50.479Z [SMOOTHING0] Clearing queued colors before: disabling. Smoothing configuration changed: restarting timer.
2025-06-24T22:19:50.479Z [SMOOTHING0] Smoothing queue is cleared
2025-06-24T22:19:50.479Z [SMOOTHING0] Selecting config (0) => type: Alternative, pause: false, settlingTime: 25ms, interval: 17ms (58Hz), antiFlickTres: 0, antiFlickStep: 0, antiFlickTime: 0
2025-06-24T22:19:50.479Z [SMOOTHING0] Selecting config (0) => type: Alternative, pause: false, settlingTime: 25ms, interval: 17ms (58Hz), antiFlickTres: 0, antiFlickStep: 0, antiFlickTime: 0
2025-06-24T22:19:50.479Z [LEDDEVICE0_HYPERSPI] Start LedDevice 'hyperspi'.
2025-06-24T22:19:50.479Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:336) deviceConfig: [{"colorOrder":"rgb","currentLedCount":314,"invert":false,"output":"/dev/spidev0.0","rate":25000000,"refreshTime":17,"smoothingRefreshTime":0,"spitype":"rp2040","type":"hyperspi","white_channel_blue":255,"white_channel_calibration":true,"white_channel_green":255,"white_channel_limit":100,"white_channel_red":255}]
2025-06-24T22:19:50.479Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:422) Refresh rate = 58.82 Hz
2025-06-24T22:19:50.479Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:372) Device is not ready to start a timer
2025-06-24T22:19:50.479Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:432) Refresh interval updated to 17ms
2025-06-24T22:19:50.479Z [LEDDEVICE0_HYPERSPI] (ProviderSpi.cpp:52) Speed: 20833333, Type: rp2040
2025-06-24T22:19:50.479Z [LEDDEVICE0_HYPERSPI] (ProviderSpi.cpp:53) Inverted: no, Mode: 0
2025-06-24T22:19:50.479Z [LEDDEVICE0_HYPERSPI] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2025-06-24T22:19:50.479Z [LEDDEVICE0_HYPERSPI] (DriverSpiHyperSPI.cpp:79) SPI driver with data integration check AWA protocol
2025-06-24T22:19:50.479Z [LEDDEVICE0_HYPERSPI] (DriverSpiHyperSPI.cpp:87) SPI header for 314 leds: AwA 0x01 0x39 0x6d
2025-06-24T22:19:50.479Z [LEDDEVICE0_HYPERSPI] (DriverSpiHyperSPI.cpp:64) White channel limit: 255, red: 255, green: 255, blue: 255
2025-06-24T22:19:50.479Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:246) Enable the device
2025-06-24T22:19:50.480Z [HYPER_MANAGER] HyperHDR instance 'First LED instance' has been started
2025-06-24T22:19:50.480Z [HYPERHDR0] The instance is running
2025-06-24T22:19:50.480Z [MUXER0] Register new input 'System/VIDEOGRABBER' with priority 150 as inactive
2025-06-24T22:19:50.480Z [COMPONENTCTRL0] Video capture device: enabled
2025-06-24T22:19:50.480Z [V4L2:USB3.0 UHD: US] Multithreading for V4L2 is enabled. Available thread's count 3
2025-06-24T22:19:50.480Z [V4L2:USB3.0 UHD: US] Found capture device: /dev/video15
2025-06-24T22:19:50.480Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:63) Switch on
2025-06-24T22:19:50.480Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:139) Power On
2025-06-24T22:19:50.480Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:366) Starting timer with interval = 17ms
2025-06-24T22:19:50.480Z [COMPONENTCTRL0] LED device: enabled
2025-06-24T22:19:50.480Z [V4L2:USB3.0 UHD: US] Found capture device: /dev/video21
2025-06-24T22:19:50.481Z [V4L2:USB3.0 UHD: US] Found capture device: /dev/video14
2025-06-24T22:19:50.481Z [V4L2:USB3.0 UHD: US] Found capture device: /dev/video22
2025-06-24T22:19:50.481Z [V4L2:USB3.0 UHD: US] Found capture device: /dev/video0
2025-06-24T22:19:50.481Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:425) Device has 'brightness' control => min: 0, max: 100, default: 50
2025-06-24T22:19:50.481Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:431) Device has 'contrast' control => min: 0, max: 100, default: 50
2025-06-24T22:19:50.481Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:437) Device has 'saturation' control => min: 0, max: 100, default: 50
2025-06-24T22:19:50.481Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:443) Device has 'hue' control => min: 0, max: 100, default: 50
2025-06-24T22:19:50.482Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:232) Searching for USB3.0 UHD: USB3.0 UHD (video0) 1280 x 1024 @ 60 fps, input: -1 (yuyv)
2025-06-24T22:19:50.482Z [V4L2:USB3.0 UHD: US] *************************************************************************************************
2025-06-24T22:19:50.482Z [V4L2:USB3.0 UHD: US] Starting V4L2 grabber. Selected: USB3.0 UHD: USB3.0 UHD (video0) [/dev/video0] 1280 x 1024 @ 60 fps yuyv input -1
2025-06-24T22:19:50.482Z [V4L2:USB3.0 UHD: US] *************************************************************************************************
2025-06-24T22:19:50.482Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:867) Hardware cropping is not supported: ignoring
2025-06-24T22:19:50.482Z [V4L2:USB3.0 UHD: US] Set device input to: Camera 1
2025-06-24T22:19:50.483Z [FLATBUFSERVER] Tone mapping: 0
2025-06-24T22:19:50.483Z [FLATBUFSERVER] Started on port 19400
2025-06-24T22:19:50.483Z [MQTT] (mqtt.cpp:53) Starting the MQTT connection. Address: 192.168.1.49:1883. Protocol: NO SSL. Authentication: YES, Ignore errors: YES
2025-06-24T22:19:50.483Z [MQTT] (mqtt.cpp:58) MQTT topic: hyperhdr/JsonAPI, MQTT response: hyperhdr/JsonAPI/response
2025-06-24T22:19:50.483Z [WEBSERVER] Initialize Webserver
2025-06-24T22:19:50.483Z [FLATBUFSERVER] Started local domain socket server: 'hyperhdr-domain'
2025-06-24T22:19:50.483Z [FLATBUFSERVER] Tone mapping: 0
2025-06-24T22:19:50.483Z [FLATBUFSERVER] NV12 quarter of frame mode: 0
2025-06-24T22:19:50.484Z [MQTT] Error: SocketNetworkError
2025-06-24T22:19:50.484Z [MQTT] (mqtt.cpp:209) Prepare to retry in 10 seconds (limit: 3)
2025-06-24T22:19:50.484Z [NETFORWARDER] Forwarder has changed state to disabled
2025-06-24T22:19:50.498Z [V4L2:USB3.0 UHD: US] Set resolution to: 1280 x 1024
2025-06-24T22:19:50.514Z [WEBSERVER] Apply Webserver settings
2025-06-24T22:19:50.514Z [WEBSERVER] Set document root to: :/www
2025-06-24T22:19:50.514Z [WEBSERVER] Started: 'HyperHDR WebServer (HTTP)' on port: 8090
2025-06-24T22:19:50.514Z [SSDP] (SSDPHandler.cpp:93) The local address is empty
2025-06-24T22:19:50.514Z [WEBSERVER] Initialize Webserver
2025-06-24T22:19:50.514Z [WEBSERVER] Apply Webserver settings
2025-06-24T22:19:50.514Z [WEBSERVER] Set document root to: :/www
2025-06-24T22:19:50.515Z [V4L2:USB3.0 UHD: US] Set framerate to 60 FPS
2025-06-24T22:19:50.518Z [V4L2:USB3.0 UHD: US] Brightness set to: 50 (default)
2025-06-24T22:19:50.521Z [V4L2:USB3.0 UHD: US] Contrast set to: 50 (default)
2025-06-24T22:19:50.523Z [WEBSERVER] Setup SSL certificate
2025-06-24T22:19:50.525Z [V4L2:USB3.0 UHD: US] Saturation set to: 50 (default)
2025-06-24T22:19:50.525Z [WEBSERVER] Setup private SSL key
2025-06-24T22:19:50.525Z [WEBSERVER] Started: 'HyperHDR WebServer (HTTPS)' on port: 8092
2025-06-24T22:19:50.525Z [SSDP] (SSDPHandler.cpp:42) SSDPHandler is initializing
2025-06-24T22:19:50.526Z [SSDP] Could not obtain the local address. Retry later (1/10)
2025-06-24T22:19:50.526Z [SSDP] (SSDPServer.cpp:94) Initialize the SSDP server
2025-06-24T22:19:50.526Z [SSDP] (SSDPHandler.cpp:93) The local address is empty
2025-06-24T22:19:50.528Z [V4L2:USB3.0 UHD: US] Hue set to: 50 (default)
2025-06-24T22:19:50.528Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:123) LUT folder location: '/usr/share/hyperhdr/lut'
2025-06-24T22:19:50.528Z [V4L2:USB3.0 UHD: US] (LutLoader.cpp:73) LUT file found: /home/edo/.hyperhdr/lut_lin_tables.3d (uncompressed)
2025-06-24T22:19:50.528Z [V4L2:USB3.0 UHD: US] (LutLoader.cpp:89) Index 2 for YUV
2025-06-24T22:19:50.726Z [V4L2:USB3.0 UHD: US] Found and loaded LUT: '/home/edo/.hyperhdr/lut_lin_tables.3d'
2025-06-24T22:19:50.726Z [V4L2:USB3.0 UHD: US] Video pixel format is set to: YUYV
2025-06-24T22:19:50.736Z [V4L2:USB3.0 UHD: US] Started
2025-06-24T22:19:50.738Z [MUXER0] Set visible priority to 255
2025-06-24T22:19:50.738Z [HYPERHDR0] New priority[255], previous [255]
2025-06-24T22:19:50.738Z [HYPERHDR0] No source left -> switch LED-Device off
2025-06-24T22:19:50.738Z [SMOOTHING0] Clearing queued colors before: disabling
2025-06-24T22:19:50.738Z [SMOOTHING0] Smoothing queue is cleared
2025-06-24T22:19:50.738Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:224) setBackLightEnabled: 0
2025-06-24T22:19:50.738Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:296) Disable the device
2025-06-24T22:19:50.738Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:380) Stopping refresh timer
2025-06-24T22:19:50.738Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:89) Switch off
2025-06-24T22:19:50.738Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:125) Power Off
2025-06-24T22:19:50.738Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:543) Set LED strip to black/power off
2025-06-24T22:19:50.740Z [LEDDEVICE0_HYPERSPI] (ProviderSpi.cpp:135) Closing SPI interface
2025-06-24T22:19:50.741Z [COMPONENTCTRL0] LED device: disabled
2025-06-24T22:19:50.773Z [V4L2:USB3.0 UHD: US] (V4L2Grabber.cpp:1231) Worker's thread count  = 3
2025-06-24T22:19:50.776Z [MUXER0] Priority 150 is now active
2025-06-24T22:19:50.776Z [MUXER0] Set visible priority to 150
2025-06-24T22:19:50.776Z [HYPERHDR0] New priority[150], previous [255]
2025-06-24T22:19:50.776Z [HYPERHDR0] New source available -> switch LED-Device on
2025-06-24T22:19:50.776Z [SMOOTHING0] Clearing queued colors before: enabling
2025-06-24T22:19:50.776Z [SMOOTHING0] Smoothing queue is cleared
2025-06-24T22:19:50.776Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:246) Enable the device
2025-06-24T22:19:50.776Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:224) setBackLightEnabled: 1
2025-06-24T22:19:50.777Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:63) Switch on
2025-06-24T22:19:50.777Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:139) Power On
2025-06-24T22:19:50.777Z [IMAGETOLED_MNG0] Total index number is: 60718 (memory: 60718). User sparse processing is: disabled, image size: 640 x 512, area number: 314
2025-06-24T22:19:50.777Z [LEDDEVICE0_HYPERSPI] (LedDevice.cpp:366) Starting timer with interval = 17ms
2025-06-24T22:19:50.778Z [COMPONENTCTRL0] LED device: enabled
2025-06-24T22:19:50.979Z [IMAGETOLED_MNG0] Total index number is: 60718 (memory: 60718). User sparse processing is: disabled, image size: 640 x 512, area number: 314
2025-06-24T22:19:52.040Z [NET_DISCOVERY] Found Pico/RP2040 at ttyACM0:-1 (Pico)
2025-06-24T22:19:52.017Z [SERVICE_mDNS] Failed to open any client sockets
2025-06-24T22:19:57.532Z [WEBSERVER] Web server resources initialized: /usr/share/hyperhdr/bin/../lib/web_resources.rcc
2025-06-24T22:19:58.237Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::ffff:192.168.1.10
2025-06-24T22:20:00.051Z [MQTT] (mqtt.cpp:223) Retrying 1/3
2025-06-24T22:20:00.068Z [MQTT] (mqtt.cpp:129) Connected
2025-06-24T22:20:00.068Z [MQTT] (mqtt.cpp:136) Removing retry timer
2025-06-24T22:20:07.047Z [SERVICE_mDNS] Starting the network discovery thread
2025-06-24T22:20:07.229Z [NET_DISCOVERY] Found Home Assistant at 192.168.1.49:8123 (1258ef21b967492984fbba12c29fef18.local)
2025-06-24T22:20:37.250Z [SSDP] (SSDPHandler.cpp:42) SSDPHandler is initializing
2025-06-24T22:20:37.250Z [SSDP] (SSDPHandler.cpp:183) The local address is: 192.168.1.78
2025-06-24T22:20:37.250Z [SSDP] (SSDPServer.cpp:94) Initialize the SSDP server
2025-06-24T22:20:37.250Z [SSDP] Starting the SSDP server
2025-06-24T22:22:07.463Z [PERFORMANCE] [USB: FPS = 59.41, decoding = 2ms, frames = 3565, invalid = 0, mode = direct], [INSTANCE0: FPS = 59.41, processed = 3564], [LED0: FPS = 118.24, send = 7093, processed = 3564, dropped = 0]
2025-06-24T22:22:07.463Z [V4L2:USB3.0 UHD: US] Video cache: size: 2, hits: 7099, needed: 1, cleanup: 0, limit: 8
2025-06-24T22:22:37.146Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"hyperspi","subcommand":"discover","tan":520}]
2025-06-24T22:22:37.147Z [LEDDEVICE_HYPERSPI] (ProviderSpi.cpp:319) SPI devices discovered: [{"devices":[{"name":"/dev/spidev0.0","value":"/dev/spidev0.0"},{"name":"/dev/spidev0.1","value":"/dev/spidev0.1"}],"ledDeviceType":"hyperspi"}]
2025-06-24T22:22:37.148Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"/dev/spidev0.0","value":"/dev/spidev0.0"},{"name":"/dev/spidev0.1","value":"/dev/spidev0.1"}],"ledDeviceType":"hyperspi"}]
2025-06-24T22:22:37.826Z [WEBSOCKET] (HyperAPI.cpp:946) log streaming activated for client ::ffff:192.168.1.10

Overview is also showing communcation:

When i want to open de dubug it remains empty:

What am i missing or doing wrong?

Tnx all!

Found it, was doing a double check on the wiring on the Adafruit Scorpio rp2040 the yellow wire was on A1 not on A0.

Tnx all anywat..

[awawa-dev]

Hi
At first glance, your Adafruit Scorpio SPI input pinout configuration (MOSI,SCK,CE0) is wrong.

[awawa-dev]

Also it should be spi1:

HyperSPI/.github/workflows/push-master-pico.yml

Line 62 in 6c3f17d

cmake -DOVERRIDE_DATA_PIN=16 -DOVERRIDE_SPI_DATA_PIN=28 -DOVERRIDE_SPI_CLOCK_PIN=26 -DOVERRIDE_SPI_CHIP_SELECT=29 -DOVERRIDE_SPI_INTERFACE=spi1 -DCMAKE_BUILD_TYPE=Release ..