don't translate single variable messages (#4338)

Author: nerdCopter

locales/en/messages.json

@@ -1334,7 +1334,8 @@
         "message": "Permanently enable Airmode"
     },
     "featureAIRMODETip": {
-        "message": "$t(auxiliaryHelpMode_AIRMODE.message)"
+        "message": "$t(auxiliaryHelpMode_AIRMODE.message)",
+        "description": "Don't translate!!!"
     },
     "featureRX_SPI": {
         "message": "SPI Rx (e.g. built-in Rx)"
@@ -1412,7 +1413,8 @@
         "message": "The magnetic declination is the angle between magnetic north and true north. It is different for every location on earth. You can find the declination for your location on the internet"
     },
     "configurationRangefinder": {
-        "message": "$t(initialSetupSensorSonar.message)"
+        "message": "$t(initialSetupSensorSonar.message)",
+        "description": "Don't translate!!!"
     },
     "configurationRangefinderHelp": {
         "message": "Enable rangefinder to measure distance to ground in cm"
@@ -1421,13 +1423,15 @@
         "message": "Type"
     },
     "configurationOpticalflow": {
-        "message": "$t(initialSetupSensorOpticalflow.message)"
+        "message": "$t(initialSetupSensorOpticalflow.message)",
+        "description": "Don't translate!!!"
     },
     "configurationOpticalflowHelp": {
         "message": "Enable optical flow sensor"
     },
     "configurationOpticalflowType": {
-        "message": "$t(configurationRangefinderType.message)"
+        "message": "$t(configurationRangefinderType.message)",
+        "description": "Don't translate!!!"
     },
     "configurationBoardAlignment": {
         "message": "Board Alignment"
@@ -1448,13 +1452,16 @@
         "message": "The gyro alignment is the orientation of the gyro sensor on the flight controller board. The default is usually correct, but if you have a custom build or a flight controller with a different gyro orientation, you may need to adjust this setting."
     },
     "configurationGyroAlignmentRoll": {
-        "message": "$t(configurationBoardAlignmentRoll.message)"
+        "message": "$t(configurationBoardAlignmentRoll.message)",
+        "description": "Don't translate!!!"
     },
     "configurationGyroAlignmentPitch": {
-        "message": "$t(configurationBoardAlignmentPitch.message)"
+        "message": "$t(configurationBoardAlignmentPitch.message)",
+        "description": "Don't translate!!!"
     },
     "configurationGyroAlignmentYaw": {
-        "message": "$t(configurationBoardAlignmentYaw.message)"
+        "message": "$t(configurationBoardAlignmentYaw.message)",
+        "description": "Don't translate!!!"
     },
     "configurationMagAlignment": {
         "message": "Magnetometer Alignment"
@@ -1463,13 +1470,16 @@
         "message": "Arbitrary board rotation in degrees, to allow mounting it sideways / upside down / rotated etc. When running external sensors, use the sensor alignments (Gyro, Acc, Mag) to define sensor position independent from board orientation. "
     },
     "configurationMagAlignmentRoll": {
-        "message": "$t(configurationBoardAlignmentRoll.message)"
+        "message": "$t(configurationBoardAlignmentRoll.message)",
+        "description": "Don't translate!!!"
     },
     "configurationMagAlignmentPitch": {
-        "message": "$t(configurationBoardAlignmentPitch.message)"
+        "message": "$t(configurationBoardAlignmentPitch.message)",
+        "description": "Don't translate!!!"
     },
     "configurationMagAlignmentYaw": {
-        "message": "$t(configurationBoardAlignmentYaw.message)"
+        "message": "$t(configurationBoardAlignmentYaw.message)",
+        "description": "Don't translate!!!"
     },
     "configurationSensorAlignmentGyro": {
         "message": "GYRO Alignment"