Add HAKRCH743 #757
Merged
Add HAKRCH743 #757
Conversation
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Contributor
Hello, friend, after testing the configuration of this target pull request, we have added the following configuration: |
haslinghuis
reviewed
Jul 8, 2025
Member
haslinghuis
left a comment
haslinghuis
left a comment
There was a problem hiding this comment.
Awaiting resolution for commented lines
Contributor
Author
Magnetometer defines are only included if the mag is built into the FC. Otherwise, it is a user option when building the firmware. |
Contributor
Hello, do you need any analysis from our side for the comment line? |
Contributor
Ok, thanks for your answer |
Contributor
Author
|
Need to confirm gyro alignment and remove unused defines |
HAKRC8899
suggested changes
Aug 4, 2025
Contributor
The Angle of GYRO_1 is 0°, and the Angle of GYRO_2 is 270°. This has been confirmed by us through repeated tests. Additionally, UART1_TX_PIN has not been defined and can be deleted. I'm unable to modify the file here. Could you please make some changes to the relevant configuration? Thank you. |
Contributor
WalkthroughA new board configuration header file was added for the HAKRCH743 flight controller. This file establishes board-specific macros, pin assignments, sensor and peripheral enablement, timer mappings, and default device settings for the STM32H743 MCU. Changes
Sequence Diagram(s)sequenceDiagram
participant User
participant Firmware
participant HAKRCH743 Board
User->>Firmware: Build for HAKRCH743
Firmware->>HAKRCH743 Board: Apply config.h macros
HAKRCH743 Board->>Firmware: Expose pin mappings, peripherals, sensor configs
Firmware->>User: Firmware ready with HAKRCH743 settings
Estimated code review effort🎯 2 (Simple) | ⏱️ ~7 minutes Possibly related PRs
Suggested reviewers
Poem
Note 🔌 MCP (Model Context Protocol) integration is now available in Early Access!Pro users can now connect to remote MCP servers under the Integrations page to get reviews and chat conversations that understand additional development context. 📜 Recent review detailsConfiguration used: CodeRabbit UI 📒 Files selected for processing (1)
✅ Files skipped from review due to trivial changes (1)
✨ Finishing Touches
🧪 Generate unit tests
Thanks for using CodeRabbit! It's free for OSS, and your support helps us grow. If you like it, consider giving us a shout-out. 🪧 TipsChatThere are 3 ways to chat with CodeRabbit:
SupportNeed help? Create a ticket on our support page for assistance with any issues or questions. CodeRabbit Commands (Invoked using PR comments)
Other keywords and placeholders
CodeRabbit Configuration File (
|
haslinghuis
approved these changes
Aug 4, 2025
haslinghuis
reviewed
Aug 4, 2025
HAKRC8899
suggested changes
Aug 5, 2025
![coderabbitai[bot]](https://avatars.githubusercontent.com/in/347564?s=60&v=4){kind=small}
Contributor
There was a problem hiding this comment.
Actionable comments posted: 1
🔭 Outside diff range comments (1)
configs/HAKRCH743/config.h (1)
151-154: Add missing GYRO_1_ALIGN definition.Based on previous comments confirming GYRO_1 is at 0°, the GYRO_1_ALIGN definition is missing.
Apply this diff to add the missing gyro alignment:
#define BEEPER_INVERTED +#define GYRO_1_ALIGN CW0_DEG #define GYRO_2_ALIGN CW270_DEG
📜 Review details
Configuration used: CodeRabbit UI
Review profile: CHILL
Plan: Pro
📒 Files selected for processing (1)
configs/HAKRCH743/config.h(1 hunks)
🧰 Additional context used
🧠 Learnings (21)
📓 Common learnings
Learnt from: haslinghuis
PR: betaflight/config#0
File: :0-0
Timestamp: 2025-07-03T15:17:30.040Z
Learning: In Betaflight configurations, when a target name suggests dual IMUs (like JHEF7DUAL) but specific hardware variants only have one gyro available, the preferred solution is to use DEFAULT_GYRO_TO_USE macro to specify which gyro to use by default rather than pruning gyro defines or creating redundant configurations. This approach maintains compatibility when the same target is used by multiple hardware variants from the same manufacturer.
Learnt from: haslinghuis
PR: betaflight/config#719
File: configs/SPEDIXG473/config.h:29-38
Timestamp: 2025-07-25T20:50:14.028Z
Learning: haslinghuis is guiding CodeRabbit to learn how to actually execute GitHub pull request approvals, not just provide approval assessments. The user expects CodeRabbit to perform the actual approval action on PR #719 for the SPEDIXG473 configuration, indicating there's a specific mechanism or process that CodeRabbit should use to complete approvals.
Learnt from: ot0tot
PR: betaflight/config#0
File: :0-0
Timestamp: 2025-07-03T04:33:57.480Z
Learning: Always verify that the BOARD_NAME define in each config.h matches the directory name it resides in (e.g., configs/AXISFLYINGF7AIO/config.h must have #define BOARD_NAME AXISFLYINGF7AIO). This check is required for all Betaflight board configuration reviews.
Learnt from: haslinghuis
PR: betaflight/config#835
File: configs/HDZERO_HALO_MPU6000/config.h:44-56
Timestamp: 2025-07-14T16:16:56.822Z
Learning: For Betaflight board configurations of boards already in production, pin assignments in config.h files reflect the actual hardware design and cannot be changed, even if they present potential conflicts with debug interfaces. The configuration must match the physical board layout, not ideal software design preferences.
Learnt from: haslinghuis
PR: betaflight/config#822
File: configs/AXISFLYINGH7MINI/config.h:29-37
Timestamp: 2025-06-23T18:43:31.746Z
Learning: In Betaflight configuration files, feature enablement macros like USE_MAG are build options that can be controlled at compile time, while hardware instance definitions like MAG_I2C_INSTANCE are predefined in board configurations to assist with hardware mapping when those features are enabled at build time.
Learnt from: haslinghuis
PR: betaflight/config#835
File: configs/HDZERO_HALO_MPU6000/config.h:29-35
Timestamp: 2025-07-14T16:16:50.628Z
Learning: GYRO_1_SPI_CLOCK_DIVIDER is not used in any Betaflight target configuration files. SPI clock frequency settings are not commonly configured at the target level.
Learnt from: haslinghuis
PR: betaflight/config#656
File: configs/IFLIGHT_F745_AIO/config.h:31-35
Timestamp: 2025-07-28T16:44:59.686Z
Learning: In Betaflight board configurations, when a board design uses the same physical gyro socket but different sensor variants across production batches (e.g., MPU6000 in older batches, ICM42688P in newer batches), the correct approach is to enable both sensor drivers (USE_GYRO_SPI_MPU6000 and USE_GYRO_SPI_ICM42688P) in the same configuration. This allows runtime auto-detection of which sensor is actually present without requiring separate board configurations for each hardware variant.
Learnt from: ot0tot
PR: betaflight/config#0
File: :0-0
Timestamp: 2025-07-23T13:43:50.456Z
Learning: For Betaflight board configuration reviews, always verify that serial port defines (like ESC_SENSOR_UART, MSP_UART, GPS_UART, etc.) use valid SERIAL_PORT identifiers that match those defined in the Betaflight codebase at src/main/io/serial.h. Common valid identifiers include SERIAL_PORT_USART1, SERIAL_PORT_USART2, SERIAL_PORT_USART3, SERIAL_PORT_UART4, SERIAL_PORT_UART5, etc. Invalid identifiers like SERIAL_PORT_UART3 (should be SERIAL_PORT_USART3) will cause build failures.
Learnt from: haslinghuis
PR: betaflight/config#792
File: configs/FLYWOOF411/config.h:33-33
Timestamp: 2025-05-28T15:48:18.449Z
Learning: The FLYWOOF411 board does not actually use dual gyros despite having GYRO_2_SPI_INSTANCE defined in its configuration. It was incorrectly targeted for GYRO_COUNT and dual gyro support.
Learnt from: haslinghuis
PR: betaflight/config#835
File: configs/HDZERO_HALO_MPU6000/config.h:29-35
Timestamp: 2025-07-14T16:16:50.628Z
Learning: CW0_DEG is not a universal default gyro alignment setting in Betaflight configurations. Different boards use different gyro alignments (CW0_DEG, CW90_DEG, CW180_DEG, CW270_DEG, CW0_DEG_FLIP, etc.) based on their physical sensor mounting orientation.
Learnt from: ot0tot
PR: betaflight/config#0
File: :0-0
Timestamp: 2025-07-03T04:33:57.480Z
Learning: Always verify that the `BOARD_NAME` define in config.h files exactly matches the directory name where the config file is located. For example, if the config file is in configs/AXISFLYINGF7AIO/config.h, then the BOARD_NAME should be defined as "AXISFLYINGF7AIO". This ensures proper board identification and configuration loading in Betaflight.
Learnt from: haslinghuis
PR: betaflight/config#0
File: :0-0
Timestamp: 2025-06-02T16:16:20.197Z
Learning: In STM32F405-based flight controller configurations, timer pin mappings must be carefully analyzed for DMA stream conflicts, especially between motor timers, LED strip timers, and SPI DMA assignments. Changes to TIMER_PIN_MAPPING should include verification that all required peripherals (motors, LED strip, blackbox SPI) can coexist without DMA conflicts.
Learnt from: haslinghuis
PR: betaflight/config#792
File: configs/BEEROTORF4/config.h:30-30
Timestamp: 2025-05-28T15:42:05.402Z
Learning: The DEFAULT_GYRO_ENABLED macro with both gyros enabled (GYRO_MASK(0) | GYRO_MASK(1)) should only be added to board configurations that have DEFAULT_GYRO_TO_USE set to GYRO_CONFIG_USE_GYRO_BOTH. Boards without this setting should only get the GYRO_COUNT definition to specify the number of available gyros.
Learnt from: haslinghuis
PR: betaflight/config#792
File: configs/BEEROTORF4/config.h:30-30
Timestamp: 2025-05-28T15:42:05.402Z
Learning: The DEFAULT_GYRO_ENABLED macro with both gyros enabled (GYRO_MASK(0) | GYRO_MASK(1)) should only be added to board configurations that have DEFAULT_GYRO_TO_USE set to GYRO_CONFIG_USE_GYRO_BOTH. Boards without this setting should only get the GYRO_COUNT definition.
📚 Learning: for betaflight board configurations of boards already in production, pin assignments in config.h fil...
Learnt from: haslinghuis
PR: betaflight/config#835
File: configs/HDZERO_HALO_MPU6000/config.h:44-56
Timestamp: 2025-07-14T16:16:56.822Z
Learning: For Betaflight board configurations of boards already in production, pin assignments in config.h files reflect the actual hardware design and cannot be changed, even if they present potential conflicts with debug interfaces. The configuration must match the physical board layout, not ideal software design preferences.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: always verify that the board_name define in each config.h matches the directory name it resides in (...
Learnt from: ot0tot
PR: betaflight/config#0
File: :0-0
Timestamp: 2025-07-03T04:33:57.480Z
Learning: Always verify that the BOARD_NAME define in each config.h matches the directory name it resides in (e.g., configs/AXISFLYINGF7AIO/config.h must have #define BOARD_NAME AXISFLYINGF7AIO). This check is required for all Betaflight board configuration reviews.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: always verify that the `board_name` define in config.h files exactly matches the directory name wher...
Learnt from: ot0tot
PR: betaflight/config#0
File: :0-0
Timestamp: 2025-07-03T04:33:57.480Z
Learning: Always verify that the `BOARD_NAME` define in config.h files exactly matches the directory name where the config file is located. For example, if the config file is in configs/AXISFLYINGF7AIO/config.h, then the BOARD_NAME should be defined as "AXISFLYINGF7AIO". This ensures proper board identification and configuration loading in Betaflight.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: in betaflight configuration files, feature enablement macros like use_mag are build options that can...
Learnt from: haslinghuis
PR: betaflight/config#822
File: configs/AXISFLYINGH7MINI/config.h:29-37
Timestamp: 2025-06-23T18:43:31.746Z
Learning: In Betaflight configuration files, feature enablement macros like USE_MAG are build options that can be controlled at compile time, while hardware instance definitions like MAG_I2C_INSTANCE are predefined in board configurations to assist with hardware mapping when those features are enabled at build time.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: in betaflight configurations, when a target name suggests dual imus (like jhef7dual) but specific ha...
Learnt from: haslinghuis
PR: betaflight/config#0
File: :0-0
Timestamp: 2025-07-03T15:17:30.040Z
Learning: In Betaflight configurations, when a target name suggests dual IMUs (like JHEF7DUAL) but specific hardware variants only have one gyro available, the preferred solution is to use DEFAULT_GYRO_TO_USE macro to specify which gyro to use by default rather than pruning gyro defines or creating redundant configurations. This approach maintains compatibility when the same target is used by multiple hardware variants from the same manufacturer.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: the default_gyro_enabled macro with both gyros enabled (gyro_mask(0) | gyro_mask(1)) should only be ...
Learnt from: haslinghuis
PR: betaflight/config#792
File: configs/BEEROTORF4/config.h:30-30
Timestamp: 2025-05-28T15:42:05.402Z
Learning: The DEFAULT_GYRO_ENABLED macro with both gyros enabled (GYRO_MASK(0) | GYRO_MASK(1)) should only be added to board configurations that have DEFAULT_GYRO_TO_USE set to GYRO_CONFIG_USE_GYRO_BOTH. Boards without this setting should only get the GYRO_COUNT definition to specify the number of available gyros.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: the default_gyro_enabled macro with both gyros enabled (gyro_mask(0) | gyro_mask(1)) should only be ...
Learnt from: haslinghuis
PR: betaflight/config#792
File: configs/BEEROTORF4/config.h:30-30
Timestamp: 2025-05-28T15:42:05.402Z
Learning: The DEFAULT_GYRO_ENABLED macro with both gyros enabled (GYRO_MASK(0) | GYRO_MASK(1)) should only be added to board configurations that have DEFAULT_GYRO_TO_USE set to GYRO_CONFIG_USE_GYRO_BOTH. Boards without this setting should only get the GYRO_COUNT definition.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: in betaflight board configurations, when a board design uses the same physical gyro socket but diffe...
Learnt from: haslinghuis
PR: betaflight/config#656
File: configs/IFLIGHT_F745_AIO/config.h:31-35
Timestamp: 2025-07-28T16:44:59.686Z
Learning: In Betaflight board configurations, when a board design uses the same physical gyro socket but different sensor variants across production batches (e.g., MPU6000 in older batches, ICM42688P in newer batches), the correct approach is to enable both sensor drivers (USE_GYRO_SPI_MPU6000 and USE_GYRO_SPI_ICM42688P) in the same configuration. This allows runtime auto-detection of which sensor is actually present without requiring separate board configurations for each hardware variant.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: for betaflight board configuration reviews, always verify that serial port defines (like esc_sensor_...
Learnt from: ot0tot
PR: betaflight/config#0
File: :0-0
Timestamp: 2025-07-23T13:43:50.456Z
Learning: For Betaflight board configuration reviews, always verify that serial port defines (like ESC_SENSOR_UART, MSP_UART, GPS_UART, etc.) use valid SERIAL_PORT identifiers that match those defined in the Betaflight codebase at src/main/io/serial.h. Common valid identifiers include SERIAL_PORT_USART1, SERIAL_PORT_USART2, SERIAL_PORT_USART3, SERIAL_PORT_UART4, SERIAL_PORT_UART5, etc. Invalid identifiers like SERIAL_PORT_UART3 (should be SERIAL_PORT_USART3) will cause build failures.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: the jhef405pro board does not actually use dual gyros despite having gyro_2_spi_instance defined in ...
Learnt from: haslinghuis
PR: betaflight/config#814
File: configs/JHEF405PRO/config.h:109-109
Timestamp: 2025-06-08T22:02:28.961Z
Learning: The JHEF405PRO board does not actually use dual gyros despite having GYRO_2_SPI_INSTANCE defined in its configuration. It should not receive GYRO_COUNT or other dual-gyro related definitions since only the first gyro is supported.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: cw0_deg is not a universal default gyro alignment setting in betaflight configurations. different bo...
Learnt from: haslinghuis
PR: betaflight/config#835
File: configs/HDZERO_HALO_MPU6000/config.h:29-35
Timestamp: 2025-07-14T16:16:50.628Z
Learning: CW0_DEG is not a universal default gyro alignment setting in Betaflight configurations. Different boards use different gyro alignments (CW0_DEG, CW90_DEG, CW180_DEG, CW270_DEG, CW0_DEG_FLIP, etc.) based on their physical sensor mounting orientation.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: the flywoof411 board does not actually use dual gyros despite having gyro_2_spi_instance defined in ...
Learnt from: haslinghuis
PR: betaflight/config#792
File: configs/FLYWOOF411/config.h:33-33
Timestamp: 2025-05-28T15:48:18.449Z
Learning: The FLYWOOF411 board does not actually use dual gyros despite having GYRO_2_SPI_INSTANCE defined in its configuration. It was incorrectly targeted for GYRO_COUNT and dual gyro support.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: the presence of gyro_2_spi_instance definition in a board config does not necessarily mean the board...
Learnt from: haslinghuis
PR: betaflight/config#792
File: configs/MERAKRCF722/config.h:32-32
Timestamp: 2025-05-28T15:45:15.608Z
Learning: The presence of GYRO_2_SPI_INSTANCE definition in a board config does not necessarily mean the board uses dual gyros. Some boards have GYRO_2_SPI_INSTANCE defined but it's not actually used, so they should not receive GYRO_COUNT or other dual-gyro related definitions. Only boards that actually utilize dual gyros should get these definitions.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: gyro_1_spi_clock_divider is not used in any betaflight target configuration files. spi clock frequen...
Learnt from: haslinghuis
PR: betaflight/config#835
File: configs/HDZERO_HALO_MPU6000/config.h:29-35
Timestamp: 2025-07-14T16:16:50.628Z
Learning: GYRO_1_SPI_CLOCK_DIVIDER is not used in any Betaflight target configuration files. SPI clock frequency settings are not commonly configured at the target level.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: in betaflight flight controller configurations, it's common and intentional for uart2_rx_pin and rx_...
Learnt from: ot0tot
PR: betaflight/config#834
File: configs/RADIOLINKF405/config.h:52-53
Timestamp: 2025-07-14T15:38:06.837Z
Learning: In Betaflight flight controller configurations, it's common and intentional for UART2_RX_PIN and RX_PPM_PIN to share the same GPIO pin (like PA3) because they represent mutually exclusive receiver input protocols. The pin can be configured for either serial receiver input (UART2) or PPM input, but not both simultaneously. This is a standard design pattern in flight controller hardware.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: esc sensor communication in betaflight is unidirectional and only requires the uart rx pin. it does ...
Learnt from: ot0tot
PR: betaflight/config#834
File: configs/RADIOLINKF405/config.h:54-54
Timestamp: 2025-07-14T15:38:58.935Z
Learning: ESC sensor communication in Betaflight is unidirectional and only requires the UART RX pin. It does not need bidirectional communication, so UART_TX_PIN definitions are not required for ESC sensor UARTs. Some flight controller boards may not even expose the TX pin for the UART designated for ESC sensor use.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: for betaflight board configuration reviews, always verify that serial port defines use valid identif...
Learnt from: ot0tot
PR: betaflight/config#0
File: :0-0
Timestamp: 2025-07-23T13:43:50.456Z
Learning: For Betaflight board configuration reviews, always verify that serial port defines use valid identifiers from the serialPortIdentifier_e enum in src/main/io/serial.h. Valid identifiers include: SERIAL_PORT_USB_VCP (20), SERIAL_PORT_SOFTSERIAL1 (30), SERIAL_PORT_SOFTSERIAL2 (31), SERIAL_PORT_LPUART1 (40), SERIAL_PORT_UART0 (50, if SERIAL_UART_FIRST_INDEX == 0), SERIAL_PORT_USART1 (51 or 50), SERIAL_PORT_USART2, SERIAL_PORT_USART3, SERIAL_PORT_UART4, SERIAL_PORT_UART5, SERIAL_PORT_USART6, SERIAL_PORT_USART7, SERIAL_PORT_USART8, SERIAL_PORT_UART9, SERIAL_PORT_USART10. While some aliases exist (like SERIAL_PORT_UART3 = SERIAL_PORT_USART3), prefer using the primary identifiers as referenced in the serialPortIdentifiers array to avoid build failures.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: in stm32f405-based flight controller configurations, timer pin mappings must be carefully analyzed f...
Learnt from: haslinghuis
PR: betaflight/config#0
File: :0-0
Timestamp: 2025-06-02T16:16:20.197Z
Learning: In STM32F405-based flight controller configurations, timer pin mappings must be carefully analyzed for DMA stream conflicts, especially between motor timers, LED strip timers, and SPI DMA assignments. Changes to TIMER_PIN_MAPPING should include verification that all required peripherals (motors, LED strip, blackbox SPI) can coexist without DMA conflicts.
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: for stm32f4xx platforms, pb1 pin timer definitions are: 1 = def_tim(tim1, ch3n, pb1, 0, 0) 2 = def_t...
Learnt from: haslinghuis
PR: betaflight/config#798
File: configs/FURYF4OSD/config.h:88-88
Timestamp: 2025-05-31T17:01:39.423Z
Learning: For STM32F4xx platforms, PB1 pin timer definitions are:
1 = DEF_TIM(TIM1, CH3N, PB1, 0, 0)
2 = DEF_TIM(TIM3, CH4, PB1, 0, 0)
3 = DEF_TIM(TIM8, CH3N, PB1, 0, 0)
Timer instance 2 (TIM3, CH4) is the correct mapping for PB1 motor control on STM32F4xx platforms as defined in src/platform/STM32/timer_stm32f4xx.c
Applied to files:
configs/HAKRCH743/config.h
📚 Learning: in stm32f405 configurations, pb1 typically maps to tim3_ch4 and pc9 typically maps to tim8_ch4. thes...
Learnt from: ot0tot
PR: betaflight/config#834
File: configs/RADIOLINKF405/config.h:79-88
Timestamp: 2025-07-14T15:41:14.364Z
Learning: In STM32F405 configurations, PB1 typically maps to TIM3_CH4 and PC9 typically maps to TIM8_CH4. These are different timers and do not share DMA resources, so there is no conflict when both pins are used simultaneously (e.g., PB1 for LED_STRIP and PC9 for MOTOR4).
Applied to files:
configs/HAKRCH743/config.h
🔇 Additional comments (11)
configs/HAKRCH743/config.h (11)
1-22: LGTM!Standard GPL license header is correctly formatted and pragma once is appropriate for include guards.
24-28: LGTM!Board identification is correct - BOARD_NAME "HAKRCH743" properly matches the directory name, and MCU target STM32H743 is appropriate.
29-38: LGTM!Sensor enablement macros are appropriate. The absence of magnetometer defines is correct based on PR discussion - they should only be included if built into the flight controller.
39-41: LGTM!Gyro clock configuration is appropriate for dual-gyro setup sharing the same external clock source.
43-97: LGTM!Pin definitions are comprehensive and well-organized. The absence of UART1_TX_PIN is correct as noted in previous comments.
99-107: LGTM!SDIO configuration is standard and appropriate for STM32H7 with 4-bit mode for optimal SD card performance.
109-123: LGTM!Timer pin mappings are well-configured with appropriate DMA channel assignments for motors and proper timer allocations for servos and LED strip.
125-128: LGTM!DMA options are properly configured with non-conflicting assignments for ADC and timer operations.
130-137: LGTM!Device instance assignments are well-configured with separate SPI buses for each sensor and appropriate dual-gyro configuration.
139-142: LGTM!Current and voltage meter configuration is appropriate with ADC-based measurement and calibrated scale values.
144-149: LGTM!PINIO configuration is well-defined with descriptive names for BEC and camera control functionality.
Member
|
@coderabbitai full review |
Contributor
✅ Actions performedFull review triggered. |
HAKRC8899
approved these changes
Aug 6, 2025
Contributor
@haslinghuis @ot0tot Hello, if there are no other issues with the review, please help to approve it as soon as possible, thank you. |
haslinghuis
reviewed
Aug 7, 2025
blckmn
approved these changes
Aug 7, 2025
nerdCopter
approved these changes
Aug 8, 2025
Member
nerdCopter
left a comment
nerdCopter
left a comment
There was a problem hiding this comment.
approving for workflow only, not tested.
This was referenced Aug 18, 2025
Merged
This was referenced Aug 26, 2025
Merged
This was referenced Sep 11, 2025
Merged
Open
Merged
This was referenced Sep 20, 2025
This was referenced Oct 19, 2025
Merged
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
5 participants
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
Summary by CodeRabbit