Finish the benchtop surface

[griswaldbrooks]

The benchtop needs a coat of white paint and lacquer so the surface is easy to clean.

[PatrikD]

Alternatively, we could get a sheet of fiberglass reinforced panel at Home Depot for $23. Designed to make sure nothing sticks to it, and to be really easy to clean.

[griswaldbrooks]

Cool. That could be much easier. Does it cut with scissors or do we need a
saw? I see it's 1/16th of an inch thick.

On Jul 17, 2016 10:56 PM, "PatrikD" notifications@github.com wrote:

Alternatively, we could get a sheet of fiberglass reinforced panel
http://www.homedepot.com/p/1-16-in-x-4-ft-x-8-ft-Plastic-Panel-63003/202090190
at Home Depot for $23. Designed to make sure nothing sticks to it, and to
be really easy to clean.

—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub
#2 (comment),
or mute the thread
https://github.com/notifications/unsubscribe-auth/AAX2f755zM2tqzi2YBymWzkYfAe7Zn-Fks5qWxWfgaJpZM4JOJuw
.

[PatrikD]

Note sure - haven't worked with it yet. I doubt it can be cut with ordinary scissors, although something like metal shears might work. Dremel should work fine. We have a jigsaw as well, and I know Omni has a Sawzall, but that's probably overkill.

[griswaldbrooks]

There's also a circular saw, but we have metal shears. I hope it's not
something too heavy. We've already replaced the foam with a particle board
top. We also installed a lower level particle board shelf, and replaced the
previous wood holding together the table with 2x4's. The base is much more
sturdy now.

On 18 July 2016 at 01:47, PatrikD notifications@github.com wrote:

Note sure - haven't worked with it yet. I doubt it can be cut with
ordinary scissors, although something like metal shears might work. Dremel
should work fine. We have a jigsaw as well, and I know Omni has a Sawzall,
but that's probably overkill.

—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub
#2 (comment),
or mute the thread
https://github.com/notifications/unsubscribe-auth/AAX2f_VpDQRJUxpmMiGD2U9jz5Kx4_aNks5qWz2agaJpZM4JOJuw
.

[PatrikD]

Lots of good tips online for how to cut FRP. Consensus seems to be that it causes a lot of nasty dust since it's fiberglass reinforced. So score with a box cutter and snap, or use tin snips or electric metal shears.

http://forums.finehomebuilding.com/breaktime/tools-home-building/cutting-frp-panels

[griswaldbrooks]

We'll have to make a trip to Home Depot and check it out.

On Jul 18, 2016 2:02 AM, "PatrikD" notifications@github.com wrote:

Lots of good tips online for how to cut FRP. Consensus seems to be that it
causes a lot of nasty dust since it's fiberglass reinforced. So score with
a box cutter and snap, or use tin snips or electric metal shears.

http://forums.finehomebuilding.com/breaktime/tools-home-building/cutting-frp-panels

—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub
#2 (comment),
or mute the thread
https://github.com/notifications/unsubscribe-auth/AAX2fwlr7wUnx0PueORcWFZuQ25WImhfks5qW0EbgaJpZM4JOJuw
.

[ddigor]

Wear an N95 mask during cutting, finishing and cleanup.

[griswaldbrooks]

👍