8‐3 Delete Commands_jp

Masterファイルを直接編集するため、実行前に必ずMasterファイルをバックアップしてください。

本手順でできること

CLIから以下のdeleteコマンドを実行できます

• delete ip_address
• delete l2_segment
• delete portchannel
• delete virtual_port
• delete vport_l1if_direct_binding
• delete vport_l2_direct_binding

基本構文

python [file path]/network_sketcher.py [command] --master [master file path]

• 以下のように[command] 、--master [master file path]　の場所は変更可能
  python [file path]/network_sketcher.py -master [master file path] [command]
  

delete ip_address

レイヤ３インタフェースのIPアドレスを削除します。１回に１つのIPアドレスが削除できます。

python [file path]/network_sketcher.py delete ip_address [device name] [layer3_portname] [ip_address/subnetmask] --master [master file path] 

• ex.
  

+BEFORE+
#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'Vlan 100', '', '192.168.100.100/24']

+IP Address deleted+
＃python .\network_sketcher.py delete ip_address 'L3SW2' 'Vlan 100' '192.168.100.100/24' --master "C:\work\[MASTER]test.xlsx"
--- IP Address deleted --- L3SW2,Vlan 100,192.168.100.100/24

+AFTER+
#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'Vlan 100', '', '']

delete l2_segment

インタフェースに設定されたVLAN等のレイヤ２セグメントを削除します。１回に１つのレイヤ２セグメントが削除できます。

python [file path]/network_sketcher.py delete ip_address [device name] [layer2_portname] [l2segment_name] --master [master file path] 

• ex.
  

+BEFORE+
#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'GigabitEthernet 0/0', '', 'Vlan100,Vlan200,Vlan300,addvlan999', '']

+l2_segment deleted+
＃python .\network_sketcher.py delete l2_segment 'L3SW2' 'GigabitEthernet 0/0' 'addvlan999' --master "C:\work\[MASTER]test.xlsx"
--- l2 Segment deleted --- L3SW2,GigabitEthernet 0/0,addvlan999

+AFTER+
#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'GigabitEthernet 0/0', '', 'Vlan100,Vlan200,Vlan300', '']

delete portchannel

レイヤ１インタフェースに設定されたポートチャネル(LAG)を削除します。ポートチャネルに設定されているレイヤ２セグメントも一緒に削除されます。

python [file path]/network_sketcher.py delete portchannel [device name] [layer1_portname] --master [master file path] 

• ex.
  

+BEFORE+
#python .\network_sketcher.py show l2_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW1', 'GigabitEthernet 0/0', 'PortChannel 1', 'vlan1', '']
['L3SW1', 'GigabitEthernet 0/1', 'PortChannel 1', 'vlan1', '']

#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW1', 'PortChannel 1', '', '']

+portchannel deleted+
＃python .\network_sketcher.py delete portchannel 'L3SW1' 'GigabitEthernet 0/0' --master "C:\work\[MASTER]test.xlsx"
--- portchannel deleted --- L3SW1,GigabitEthernet 0/0,PortChannel 1

＃python .\network_sketcher.py delete portchannel 'L3SW1' 'GigabitEthernet 0/1' --master "C:\work\[MASTER]test.xlsx"
--- portchannel deleted --- L3SW1,GigabitEthernet 0/1,PortChannel 1

+AFTER+
#python .\network_sketcher.py show l2_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW1', 'GigabitEthernet 0/0', '', '', '']
['L3SW1', 'GigabitEthernet 0/1', '', '', '']

#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW1', 'GigabitEthernet 0/0', '', '']
['L3SW1', 'GigabitEthernet 0/1', '', '']

delete virtual_port

VLANインタフェース(SVI)等のレイヤ３インタフェースを削除します。ポートチャネルの削除はできません。

python [file path]/network_sketcher.py delete virtual_port [device name] [virtual_portname] --master [master file path] 

• ex.
  

+BEFORE+
#python .\network_sketcher.py show l2_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', '', 'addvlan 999', '', '']
['L3SW2', '', 'Vlan 300', 'Vlan300', '']

#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'Vlan 300', '', '']
['L3SW2', 'addvlan 999', '', '']

+virtual_port deleted+
＃python .\network_sketcher.py delete virtual_port 'L3SW2' 'addvlan 999' --master "C:\work\[MASTER]test.xlsx"
--- Virtual Port deleted --- L3SW2,addvlan 999

+AFTER+
#python .\network_sketcher.py show l2_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', '', 'Vlan 300', 'Vlan300', '']

#python .\network_sketcher.py show l3_interface --master "C:\work\[MASTER]test.xlsx"
['L3SW2', 'Vlan 300', '', '']

delete vport_l1if_direct_binding

レイヤ１ポートと接続されたVirtual Portを削除します。このコマンドによりVirtual portに接続されたVLANなどのレイヤ２要素も削除されます。

python [file path]/network_sketcher.py delete vport_l1if_direct_binding [device name] [vport_name_direct_binding] --master [master file path] 

• ex.
  

+BEFORE+
#python .\network_sketcher.py show l2_interface --master "C:\work\[MASTER]test.xlsx"
['Catalyst 3560', 'GigabitEthernet 0/0', 'GigabitEthernet 0/0.100', '', 'vlan100']

+vport_l1if_direct_binding deleted+
＃python .\network_sketcher.py delete vport_l1if_direct_binding "Catalyst 3560" "GigabitEthernet 0/0.100" --master "C:\work\[MASTER]test.xlsx"
--- vport_l1if_direct_binding deleted --- Catalyst 3560,GigabitEthernet 0/0.100,vlan100

+AFTER+
#python .\network_sketcher.py show l2_interface --master "C:\work\[MASTER]test.xlsx"
['Catalyst 3560', 'GigabitEthernet 0/0', '', '', '']

delete vport_l2_direct_binding

Virtualポートで直接VLAN(l2_segment)のようなレイヤ２を送受信する要素を削除します。

python [file path]/network_sketcher.py delete vport_l2_direct_binding [device name] [virtual port] [l2_name_direct_binding] --master [master file path] 

• ex.
  

+BEFORE+
#python .\network_sketcher.py show l2_interface --master "C:\work\[MASTER]test.xlsx"
['Catalyst 3560', 'GigabitEthernet 0/0', 'GigabitEthernet 0/0.100', '', 'vlan100']

+virtual_port deleted+
＃python .\network_sketcher.py delete vport_l2_direct_binding "Catalyst 3560" "GigabitEthernet 0/0.100" vlan100 --master "C:\work\[MASTER]test.xlsx"
--- vport_l2_direct_binding deleted --- Catalyst 3560,GigabitEthernet 0/0.100,vlan100

+AFTER+
#python .\network_sketcher.py show l2_interface --master "C:\work\[MASTER]test.xlsx"
['Catalyst 3560', 'GigabitEthernet 0/0', 'GigabitEthernet 0/0.100', '', '']