Merge tag 'pinctrl-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "Outside the pinctrl driver and DT bindings we hit some Arm DT files,
  patched by the maintainers.

  Other than that it is business as usual.

  Core changes:

   - Add PINCTRL_PINGROUP() helper macro (and use it in the AMD driver).

  New drivers:

   - Intel Meteor Lake support.

   - Reneasas RZ/V2M and r8a779g0 (R-Car V4H).

   - AXP209 variants AXP221, AXP223 and AXP809.

   - Qualcomm MSM8909, PM8226, PMP8074 and SM6375.

   - Allwinner D1.

  Improvements:

   - Proper pin multiplexing in the AMD driver.

   - Mediatek MT8192 can use generic drive strength and pin bias, then
     fixes on top plus some I2C pin group fixes.

   - Have the Allwinner Sunplus SP7021 use the generic DT schema and
     make interrupts optional.

   - Handle Qualcomm SC7280 ADSP.

   - Handle Qualcomm MSM8916 CAMSS GP clock muxing.

   - High impedance bias on ZynqMP.

   - Serialize StarFive access to MMIO.

   - Immutable gpiochip for BCM2835, Ingenic, Qualcomm SPMI GPIO"

* tag 'pinctrl-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (117 commits)
  dt-bindings: pinctrl: qcom,pmic-gpio: add PM8226 constraints
  pinctrl: qcom: Make PINCTRL_SM8450 depend on PINCTRL_MSM
  pinctrl: qcom: sm8250: Fix PDC map
  pinctrl: amd: Fix an unused variable
  dt-bindings: pinctrl: mt8186: Add and use drive-strength-microamp
  dt-bindings: pinctrl: mt8186: Add gpio-line-names property
  ARM: dts: imxrt1170-pinfunc: Add pinctrl binding header
  pinctrl: amd: Use unicode for debugfs output
  pinctrl: amd: Fix newline declaration in debugfs output
  pinctrl: at91: Fix typo 'the the' in comment
  dt-bindings: pinctrl: st,stm32: Correct 'resets' property name
  pinctrl: mvebu: Missing a blank line after declarations.
  pinctrl: qcom: Add SM6375 TLMM driver
  dt-bindings: pinctrl: Add DT schema for SM6375 TLMM
  dt-bindings: pinctrl: mt8195: Use drive-strength-microamp in examples
  Revert "pinctrl: qcom: spmi-gpio: make the irqchip immutable"
  pinctrl: imx93: Add MODULE_DEVICE_TABLE()
  pinctrl: sunxi: Add driver for Allwinner D1
  pinctrl: sunxi: Make some layout parameters dynamic
  pinctrl: sunxi: Refactor register/offset calculation
  ...

Author: torvalds

Documentation/devicetree/bindings/gpio/x-powers,axp209-gpio.yaml

@@ -19,7 +19,13 @@ properties:
     oneOf:
       - enum:
           - x-powers,axp209-gpio
+          - x-powers,axp221-gpio
           - x-powers,axp813-gpio
+      - items:
+          - enum:
+              - x-powers,axp223-gpio
+              - x-powers,axp809-gpio
+          - const: x-powers,axp221-gpio
       - items:
           - const: x-powers,axp803-gpio
           - const: x-powers,axp813-gpio

Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml

@@ -46,6 +46,7 @@ properties:
       - allwinner,sun8i-v3s-pinctrl
       - allwinner,sun9i-a80-pinctrl
       - allwinner,sun9i-a80-r-pinctrl
+      - allwinner,sun20i-d1-pinctrl
       - allwinner,sun50i-a64-pinctrl
       - allwinner,sun50i-a64-r-pinctrl
       - allwinner,sun50i-a100-pinctrl
@@ -80,9 +81,6 @@ properties:
       - const: hosc
       - const: losc
 
-  resets:
-    maxItems: 1
-
   gpio-controller: true
   interrupt-controller: true
   gpio-line-names: true
@@ -181,6 +179,18 @@ allOf:
           minItems: 7
           maxItems: 7
 
+  - if:
+      properties:
+        compatible:
+          enum:
+            - allwinner,sun20i-d1-pinctrl
+
+    then:
+      properties:
+        interrupts:
+          minItems: 6
+          maxItems: 6
+
   - if:
       properties:
         compatible:

Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml

@@ -152,7 +152,7 @@ examples:
       pinctrl-names = "default";
       pinctrl-0 = <&pinctrl_uid>, <&pinmux_uid>;
 
-      uid {
+      button-uid {
         label = "UID";
         linux,code = <102>;
         gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;

Documentation/devicetree/bindings/pinctrl/pinctrl-mt8186.yaml

@@ -28,6 +28,8 @@ properties:
   gpio-ranges:
     maxItems: 1
 
+  gpio-line-names: true
+
   reg:
     description: |
       Physical address base for gpio base registers. There are 8 different GPIO
@@ -105,31 +107,8 @@ patternProperties:
           drive-strength:
             enum: [2, 4, 6, 8, 10, 12, 14, 16]
 
-          mediatek,drive-strength-adv:
-            description: |
-              Describe the specific driving setup property.
-              For I2C pins, the existing generic driving setup can only support
-              2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they
-              can support 0.125/0.25/0.5/1mA adjustment. If we enable specific
-              driving setup, the existing generic setup will be disabled.
-              The specific driving setup is controlled by E1E0EN.
-              When E1=0/E0=0, the strength is 0.125mA.
-              When E1=0/E0=1, the strength is 0.25mA.
-              When E1=1/E0=0, the strength is 0.5mA.
-              When E1=1/E0=1, the strength is 1mA.
-              EN is used to enable or disable the specific driving setup.
-              Valid arguments are described as below:
-              0: (E1, E0, EN) = (0, 0, 0)
-              1: (E1, E0, EN) = (0, 0, 1)
-              2: (E1, E0, EN) = (0, 1, 0)
-              3: (E1, E0, EN) = (0, 1, 1)
-              4: (E1, E0, EN) = (1, 0, 0)
-              5: (E1, E0, EN) = (1, 0, 1)
-              6: (E1, E0, EN) = (1, 1, 0)
-              7: (E1, E0, EN) = (1, 1, 1)
-              So the valid arguments are from 0 to 7.
-            $ref: /schemas/types.yaml#/definitions/uint32
-            enum: [0, 1, 2, 3, 4, 5, 6, 7]
+          drive-strength-microamp:
+            enum: [125, 250, 500, 1000]
 
           bias-pull-down:
             oneOf:
@@ -291,7 +270,7 @@ examples:
           pinmux = <PINMUX_GPIO127__FUNC_SCL0>,
                    <PINMUX_GPIO128__FUNC_SDA0>;
           bias-pull-up = <MTK_PULL_SET_RSEL_001>;
-          mediatek,drive-strength-adv = <7>;
+          drive-strength-microamp = <1000>;
         };
       };
     };

Documentation/devicetree/bindings/pinctrl/pinctrl-mt8192.yaml

@@ -80,46 +80,30 @@ patternProperties:
               dt-bindings/pinctrl/mt65xx.h. It can only support 2/4/6/8/10/12/14/16mA in mt8192.
             enum: [2, 4, 6, 8, 10, 12, 14, 16]
 
-          mediatek,drive-strength-adv:
-            description: |
-              Describe the specific driving setup property.
-              For I2C pins, the existing generic driving setup can only support
-              2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they
-              can support 0.125/0.25/0.5/1mA adjustment. If we enable specific
-              driving setup, the existing generic setup will be disabled.
-              The specific driving setup is controlled by E1E0EN.
-              When E1=0/E0=0, the strength is 0.125mA.
-              When E1=0/E0=1, the strength is 0.25mA.
-              When E1=1/E0=0, the strength is 0.5mA.
-              When E1=1/E0=1, the strength is 1mA.
-              EN is used to enable or disable the specific driving setup.
-              Valid arguments are described as below:
-              0: (E1, E0, EN) = (0, 0, 0)
-              1: (E1, E0, EN) = (0, 0, 1)
-              2: (E1, E0, EN) = (0, 1, 0)
-              3: (E1, E0, EN) = (0, 1, 1)
-              4: (E1, E0, EN) = (1, 0, 0)
-              5: (E1, E0, EN) = (1, 0, 1)
-              6: (E1, E0, EN) = (1, 1, 0)
-              7: (E1, E0, EN) = (1, 1, 1)
-              So the valid arguments are from 0 to 7.
-            $ref: /schemas/types.yaml#/definitions/uint32
-            enum: [0, 1, 2, 3, 4, 5, 6, 7]
-
-          mediatek,pull-up-adv:
-            description: |
-              Pull up settings for 2 pull resistors, R0 and R1. User can
-              configure those special pins. Valid arguments are described as below:
-              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
-              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
-              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
-              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
-            $ref: /schemas/types.yaml#/definitions/uint32
-            enum: [0, 1, 2, 3]
-
-          bias-pull-down: true
-
-          bias-pull-up: true
+          drive-strength-microamp:
+            enum: [125, 250, 500, 1000]
+
+          bias-pull-down:
+            oneOf:
+              - type: boolean
+                description: normal pull down.
+              - enum: [100, 101, 102, 103]
+                description: PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0_
+                  defines in dt-bindings/pinctrl/mt65xx.h.
+              - enum: [200, 201, 202, 203]
+                description: RSEL pull down type. See MTK_PULL_SET_RSEL_
+                  defines in dt-bindings/pinctrl/mt65xx.h.
+
+          bias-pull-up:
+            oneOf:
+              - type: boolean
+                description: normal pull up.
+              - enum: [100, 101, 102, 103]
+                description: PUPD/R1/R0 pull up type. See MTK_PUPD_SET_R1R0_
+                  defines in dt-bindings/pinctrl/mt65xx.h.
+              - enum: [200, 201, 202, 203]
+                description: RSEL pull up type. See MTK_PULL_SET_RSEL_
+                  defines in dt-bindings/pinctrl/mt65xx.h.
 
           bias-disable: true
 

Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml

@@ -29,6 +29,8 @@ properties:
     description: gpio valid number range.
     maxItems: 1
 
+  gpio-line-names: true
+
   reg:
     description: |
       Physical address base for gpio base registers. There are 8 GPIO
@@ -49,7 +51,7 @@ properties:
     description: The interrupt outputs to sysirq.
     maxItems: 1
 
-  mediatek,rsel_resistance_in_si_unit:
+  mediatek,rsel-resistance-in-si-unit:
     type: boolean
     description: |
       Identifying i2c pins pull up/down type which is RSEL. It can support
@@ -98,31 +100,8 @@ patternProperties:
           drive-strength:
             enum: [2, 4, 6, 8, 10, 12, 14, 16]
 
-          mediatek,drive-strength-adv:
-            description: |
-              Describe the specific driving setup property.
-              For I2C pins, the existing generic driving setup can only support
-              2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they
-              can support 0.125/0.25/0.5/1mA adjustment. If we enable specific
-              driving setup, the existing generic setup will be disabled.
-              The specific driving setup is controlled by E1E0EN.
-              When E1=0/E0=0, the strength is 0.125mA.
-              When E1=0/E0=1, the strength is 0.25mA.
-              When E1=1/E0=0, the strength is 0.5mA.
-              When E1=1/E0=1, the strength is 1mA.
-              EN is used to enable or disable the specific driving setup.
-              Valid arguments are described as below:
-              0: (E1, E0, EN) = (0, 0, 0)
-              1: (E1, E0, EN) = (0, 0, 1)
-              2: (E1, E0, EN) = (0, 1, 0)
-              3: (E1, E0, EN) = (0, 1, 1)
-              4: (E1, E0, EN) = (1, 0, 0)
-              5: (E1, E0, EN) = (1, 0, 1)
-              6: (E1, E0, EN) = (1, 1, 0)
-              7: (E1, E0, EN) = (1, 1, 1)
-              So the valid arguments are from 0 to 7.
-            $ref: /schemas/types.yaml#/definitions/uint32
-            enum: [0, 1, 2, 3, 4, 5, 6, 7]
+          drive-strength-microamp:
+            enum: [125, 250, 500, 1000]
 
           bias-pull-down:
             oneOf:
@@ -142,7 +121,7 @@ patternProperties:
               "MTK_PUPD_SET_R1R0_11" define in mt8195.
               For pull down type is RSEL, it can add RSEL define & resistance
               value(ohm) to set different resistance by identifying property
-              "mediatek,rsel_resistance_in_si_unit".
+              "mediatek,rsel-resistance-in-si-unit".
               It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
               & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011"
               & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101"
@@ -161,7 +140,7 @@ patternProperties:
               };
               An example of using si unit resistance value(ohm):
               &pio {
-                mediatek,rsel_resistance_in_si_unit;
+                mediatek,rsel-resistance-in-si-unit;
               }
               pincontroller {
                 i2c0_pin {
@@ -190,7 +169,7 @@ patternProperties:
               "MTK_PUPD_SET_R1R0_11" define in mt8195.
               For pull up type is RSEL, it can add RSEL define & resistance
               value(ohm) to set different resistance by identifying property
-              "mediatek,rsel_resistance_in_si_unit".
+              "mediatek,rsel-resistance-in-si-unit".
               It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
               & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011"
               & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101"
@@ -209,7 +188,7 @@ patternProperties:
               };
               An example of using si unit resistance value(ohm):
               &pio {
-                mediatek,rsel_resistance_in_si_unit;
+                mediatek,rsel-resistance-in-si-unit;
               }
               pincontroller {
                 i2c0-pins {
@@ -302,7 +281,7 @@ examples:
           pinmux = <PINMUX_GPIO8__FUNC_SDA0>,
                    <PINMUX_GPIO9__FUNC_SCL0>;
           bias-disable;
-          mediatek,drive-strength-adv = <7>;
+          drive-strength-microamp = <1000>;
         };
       };
     };