Merge tag 'soc-fixes-6.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
 "A couple of platforms have some last-minute fixes, in particular:

   - riscv gets some fixes for noncoherent DMA on the renesas and thead
     platforms and dts fix for SPI on the visionfive 2 board

   - Qualcomm Snapdragon gets three dts fixes to address board specific
     regressions on the pmic and gpio nodes

   - Rockchip platforms get multiple dts fixes to address issues on the
     recent rk3399 platform as well as the older rk3128 platform that
     apparently regressed a while ago.

   - TI OMAP gets some trivial code and dts fixes and a regression fix
     for the omap1 ams-delta modem

   - NXP i.MX firmware has one fix for a use-after-free but in its error
     handling"

* tag 'soc-fixes-6.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
  soc: renesas: ARCH_R9A07G043 depends on !RISCV_ISA_ZICBOM
  riscv: only select DMA_DIRECT_REMAP from RISCV_ISA_ZICBOM and ERRATA_THEAD_PBMT
  riscv: RISCV_NONSTANDARD_CACHE_OPS shouldn't depend on RISCV_DMA_NONCOHERENT
  riscv: dts: thead: set dma-noncoherent to soc bus
  arm64: dts: rockchip: Fix i2s0 pin conflict on ROCK Pi 4 boards
  arm64: dts: rockchip: Add i2s0-2ch-bus-bclk-off pins to RK3399
  clk: ti: Fix missing omap5 mcbsp functional clock and aliases
  clk: ti: Fix missing omap4 mcbsp functional clock and aliases
  ARM: OMAP1: ams-delta: Fix MODEM initialization failure
  soc: renesas: Make ARCH_R9A07G043 depend on required options
  riscv: dts: starfive: visionfive 2: correct spi's ss pin
  firmware/imx-dsp: Fix use_after_free in imx_dsp_setup_channels()
  ARM: OMAP: timer32K: fix all kernel-doc warnings
  ARM: omap2: fix a debug printk
  ARM: dts: rockchip: Fix timer clocks for RK3128
  ARM: dts: rockchip: Add missing quirk for RK3128's dma engine
  ARM: dts: rockchip: Add missing arm timer interrupt for RK3128
  ARM: dts: rockchip: Fix i2c0 register address for RK3128
  arm64: dts: rockchip: set codec system-clock-fixed on px30-ringneck-haikou
  arm64: dts: rockchip: use codec as clock master on px30-ringneck-haikou
  ...

Author: torvalds

MAINTAINERS

@@ -13846,9 +13846,10 @@ F:	Documentation/devicetree/bindings/media/amlogic,gx-vdec.yaml
 F:	drivers/staging/media/meson/vdec/
 
 METHODE UDPU SUPPORT
-M:	Vladimir Vid <vladimir.vid@sartura.hr>
+M:	Robert Marko <robert.marko@sartura.hr>
 S:	Maintained
-F:	arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
+F:	arch/arm64/boot/dts/marvell/armada-3720-eDPU.dts
+F:	arch/arm64/boot/dts/marvell/armada-3720-uDPU.*
 
 MHI BUS
 M:	Manivannan Sadhasivam <[email protected]>

arch/arm/boot/dts/rockchip/rk3128.dtsi

@@ -64,7 +64,8 @@
 		compatible = "arm,armv7-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
 			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
-			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 		arm,cpu-registers-not-fw-configured;
 		clock-frequency = <24000000>;
 	};
@@ -233,47 +234,47 @@
 		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
 		reg = <0x20044000 0x20>;
 		interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER0>;
 		clock-names = "pclk", "timer";
 	};
 
 	timer1: timer@20044020 {
 		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
 		reg = <0x20044020 0x20>;
 		interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER1>;
 		clock-names = "pclk", "timer";
 	};
 
 	timer2: timer@20044040 {
 		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
 		reg = <0x20044040 0x20>;
 		interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER2>;
 		clock-names = "pclk", "timer";
 	};
 
 	timer3: timer@20044060 {
 		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
 		reg = <0x20044060 0x20>;
 		interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER3>;
 		clock-names = "pclk", "timer";
 	};
 
 	timer4: timer@20044080 {
 		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
 		reg = <0x20044080 0x20>;
 		interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER4>;
 		clock-names = "pclk", "timer";
 	};
 
 	timer5: timer@200440a0 {
 		compatible = "rockchip,rk3128-timer", "rockchip,rk3288-timer";
 		reg = <0x200440a0 0x20>;
 		interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER5>;
 		clock-names = "pclk", "timer";
 	};
 
@@ -426,7 +427,7 @@
 
 	i2c0: i2c@20072000 {
 		compatible = "rockchip,rk3128-i2c", "rockchip,rk3288-i2c";
-		reg = <20072000 0x1000>;
+		reg = <0x20072000 0x1000>;
 		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 		clock-names = "i2c";
 		clocks = <&cru PCLK_I2C0>;
@@ -458,6 +459,7 @@
 		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 		arm,pl330-broken-no-flushp;
+		arm,pl330-periph-burst;
 		clocks = <&cru ACLK_DMAC>;
 		clock-names = "apb_pclk";
 		#dma-cells = <1>;

arch/arm/boot/dts/ti/omap/omap4-l4-abe.dtsi

@@ -109,6 +109,8 @@
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49022000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP4_MCBSP1_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -142,6 +144,8 @@
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49024000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP4_MCBSP2_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -175,6 +179,8 @@
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49026000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP4_MCBSP3_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;

arch/arm/boot/dts/ti/omap/omap4-l4.dtsi

@@ -2043,6 +2043,8 @@
 				compatible = "ti,omap4-mcbsp";
 				reg = <0x0 0xff>; /* L4 Interconnect */
 				reg-names = "mpu";
+				clocks = <&l4_per_clkctrl OMAP4_MCBSP4_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;

arch/arm/boot/dts/ti/omap/omap5-l4-abe.dtsi

@@ -109,6 +109,8 @@
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49022000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP5_MCBSP1_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -142,6 +144,8 @@
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49024000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP5_MCBSP2_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;
@@ -175,6 +179,8 @@
 				reg = <0x0 0xff>, /* MPU private access */
 				      <0x49026000 0xff>; /* L3 Interconnect */
 				reg-names = "mpu", "dma";
+				clocks = <&abe_clkctrl OMAP5_MCBSP3_CLKCTRL 24>;
+				clock-names = "fck";
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "common";
 				ti,buffer-size = <128>;

arch/arm/mach-omap1/board-ams-delta.c

@@ -550,6 +550,7 @@ static struct platform_device *ams_delta_devices[] __initdata = {
 	&ams_delta_nand_device,
 	&ams_delta_lcd_device,
 	&cx20442_codec_device,
+	&modem_nreset_device,
 };
 
 static struct gpiod_lookup_table *ams_delta_gpio_tables[] __initdata = {
@@ -782,26 +783,28 @@ static struct plat_serial8250_port ams_delta_modem_ports[] = {
 	{ },
 };
 
+static int ams_delta_modem_pm_activate(struct device *dev)
+{
+	modem_priv.regulator = regulator_get(dev, "RESET#");
+	if (IS_ERR(modem_priv.regulator))
+		return -EPROBE_DEFER;
+
+	return 0;
+}
+
+static struct dev_pm_domain ams_delta_modem_pm_domain = {
+	.activate	= ams_delta_modem_pm_activate,
+};
+
 static struct platform_device ams_delta_modem_device = {
 	.name	= "serial8250",
 	.id	= PLAT8250_DEV_PLATFORM1,
 	.dev		= {
 		.platform_data = ams_delta_modem_ports,
+		.pm_domain = &ams_delta_modem_pm_domain,
 	},
 };
 
-static int __init modem_nreset_init(void)
-{
-	int err;
-
-	err = platform_device_register(&modem_nreset_device);
-	if (err)
-		pr_err("Couldn't register the modem regulator device\n");
-
-	return err;
-}
-
-
 /*
  * This function expects MODEM IRQ number already assigned to the port.
  * The MODEM device requires its RESET# pin kept high during probe.
@@ -833,37 +836,6 @@ static int __init ams_delta_modem_init(void)
 }
 arch_initcall_sync(ams_delta_modem_init);
 
-static int __init late_init(void)
-{
-	int err;
-
-	err = modem_nreset_init();
-	if (err)
-		return err;
-
-	/*
-	 * Once the modem device is registered, the modem_nreset
-	 * regulator can be requested on behalf of that device.
-	 */
-	modem_priv.regulator = regulator_get(&ams_delta_modem_device.dev,
-			"RESET#");
-	if (IS_ERR(modem_priv.regulator)) {
-		err = PTR_ERR(modem_priv.regulator);
-		goto unregister;
-	}
-	return 0;
-
-unregister:
-	platform_device_unregister(&ams_delta_modem_device);
-	return err;
-}
-
-static void __init ams_delta_init_late(void)
-{
-	omap1_init_late();
-	late_init();
-}
-
 static void __init ams_delta_map_io(void)
 {
 	omap1_map_io();
@@ -877,7 +849,7 @@ MACHINE_START(AMS_DELTA, "Amstrad E3 (Delta)")
 	.init_early	= omap1_init_early,
 	.init_irq	= omap1_init_irq,
 	.init_machine	= ams_delta_init,
-	.init_late	= ams_delta_init_late,
+	.init_late	= omap1_init_late,
 	.init_time	= omap1_timer_init,
 	.restart	= omap1_restart,
 MACHINE_END

arch/arm/mach-omap1/timer32k.c

@@ -176,17 +176,18 @@ static u64 notrace omap_32k_read_sched_clock(void)
 	return sync32k_cnt_reg ? readl_relaxed(sync32k_cnt_reg) : 0;
 }
 
+static struct timespec64 persistent_ts;
+static cycles_t cycles;
+static unsigned int persistent_mult, persistent_shift;
+
 /**
  * omap_read_persistent_clock64 -  Return time from a persistent clock.
+ * @ts: &struct timespec64 for the returned time
  *
  * Reads the time from a source which isn't disabled during PM, the
  * 32k sync timer.  Convert the cycles elapsed since last read into
  * nsecs and adds to a monotonically increasing timespec64.
  */
-static struct timespec64 persistent_ts;
-static cycles_t cycles;
-static unsigned int persistent_mult, persistent_shift;
-
 static void omap_read_persistent_clock64(struct timespec64 *ts)
 {
 	unsigned long long nsecs;
@@ -206,10 +207,9 @@ static void omap_read_persistent_clock64(struct timespec64 *ts)
 /**
  * omap_init_clocksource_32k - setup and register counter 32k as a
  * kernel clocksource
- * @pbase: base addr of counter_32k module
- * @size: size of counter_32k to map
+ * @vbase: base addr of counter_32k module
  *
- * Returns 0 upon success or negative error code upon failure.
+ * Returns: %0 upon success or negative error code upon failure.
  *
  */
 static int __init omap_init_clocksource_32k(void __iomem *vbase)

arch/arm/mach-omap2/omap_hwmod.c

@@ -2209,7 +2209,7 @@ int omap_hwmod_parse_module_range(struct omap_hwmod *oh,
 		return err;
 
 	pr_debug("omap_hwmod: %s %pOFn at %pR\n",
-		 oh->name, np, &res);
+		 oh->name, np, res);
 
 	if (oh && oh->mpu_rt_idx) {
 		omap_hwmod_fix_mpu_rt_idx(oh, np, res);

arch/arm64/boot/dts/qcom/apq8096-db820c.dts

@@ -62,25 +62,23 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	clocks {
-		divclk4: divclk4 {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-			clock-output-names = "divclk4";
+	div1_mclk: divclk1 {
+		compatible = "gpio-gate-clock";
+		pinctrl-0 = <&audio_mclk>;
+		pinctrl-names = "default";
+		clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
+		#clock-cells = <0>;
+		enable-gpios = <&pm8994_gpios 15 0>;
+	};
 
-			pinctrl-names = "default";
-			pinctrl-0 = <&divclk4_pin_a>;
-		};
+	divclk4: divclk4 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "divclk4";
 
-		div1_mclk: divclk1 {
-			compatible = "gpio-gate-clock";
-			pinctrl-0 = <&audio_mclk>;
-			pinctrl-names = "default";
-			clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
-			#clock-cells = <0>;
-			enable-gpios = <&pm8994_gpios 15 0>;
-		};
+		pinctrl-names = "default";
+		pinctrl-0 = <&divclk4_pin_a>;
 	};
 
 	gpio-keys {

arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi

@@ -11,26 +11,24 @@
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
 / {
-	clocks {
-		divclk1_cdc: divclk1 {
-			compatible = "gpio-gate-clock";
-			clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
-			#clock-cells = <0>;
-			enable-gpios = <&pm8994_gpios 15 GPIO_ACTIVE_HIGH>;
+	divclk1_cdc: divclk1 {
+		compatible = "gpio-gate-clock";
+		clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
+		#clock-cells = <0>;
+		enable-gpios = <&pm8994_gpios 15 GPIO_ACTIVE_HIGH>;
 
-			pinctrl-names = "default";
-			pinctrl-0 = <&divclk1_default>;
-		};
+		pinctrl-names = "default";
+		pinctrl-0 = <&divclk1_default>;
+	};
 
-		divclk4: divclk4 {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-			clock-output-names = "divclk4";
+	divclk4: divclk4 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "divclk4";
 
-			pinctrl-names = "default";
-			pinctrl-0 = <&divclk4_pin_a>;
-		};
+		pinctrl-names = "default";
+		pinctrl-0 = <&divclk4_pin_a>;
 	};
 
 	gpio-keys {