regmap: Implement regmap_multi_reg_read()

Merge series from Guenter Roeck <[email protected]>:

regmap_multi_reg_read() is similar to regmap_bilk_read() but reads from
an array of non-sequential registers. It is helpful if multiple non-
sequential registers need to be read in a single operation which would
otherwise have to be mutex protected.

The name of the new function was chosen to match the existing function
regmap_multi_reg_write().

Author: broonie

.mailmap

@@ -608,6 +608,7 @@ Simon Kelley <[email protected]>
 Sricharan Ramabadhran <[email protected]> <[email protected]>
 Srinivas Ramana <[email protected]> <[email protected]>
 Sriram R <[email protected]> <[email protected]>
+Stanislav Fomichev <[email protected]> <[email protected]>
 Stefan Wahren <[email protected]> <[email protected]>
 Stéphane Witzmann <[email protected]>
 Stephen Hemminger <[email protected]> <[email protected]>

Documentation/admin-guide/kernel-parameters.txt

@@ -2192,12 +2192,6 @@
 			Format: 0 | 1
 			Default set by CONFIG_INIT_ON_FREE_DEFAULT_ON.
 
-	init_mlocked_on_free=	[MM] Fill freed userspace memory with zeroes if
-				it was mlock'ed and not explicitly munlock'ed
-				afterwards.
-				Format: 0 | 1
-				Default set by CONFIG_INIT_MLOCKED_ON_FREE_DEFAULT_ON
-
 	init_pkru=	[X86] Specify the default memory protection keys rights
 			register contents for all processes.  0x55555554 by
 			default (disallow access to all but pkey 0).  Can

Documentation/devicetree/bindings/dma/fsl,edma.yaml

@@ -59,8 +59,8 @@ properties:
       - 3
 
   dma-channels:
-    minItems: 1
-    maxItems: 64
+    minimum: 1
+    maximum: 64
 
   clocks:
     minItems: 1

Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml

@@ -77,7 +77,7 @@ required:
   - clocks
 
 allOf:
-  - $ref: i2c-controller.yaml
+  - $ref: /schemas/i2c/i2c-controller.yaml#
   - if:
       properties:
         compatible:

Documentation/devicetree/bindings/i2c/google,cros-ec-i2c-tunnel.yaml

@@ -21,7 +21,7 @@ description: |
   google,cros-ec-spi or google,cros-ec-i2c.
 
 allOf:
-  - $ref: i2c-controller.yaml#
+  - $ref: /schemas/i2c/i2c-controller.yaml#
 
 properties:
   compatible:

Documentation/i2c/i2c_bus.svg

@@ -3,59 +3,80 @@ Introduction to I2C and SMBus
 =============================
 
 I²C (pronounce: I squared C and written I2C in the kernel documentation) is
-a protocol developed by Philips. It is a slow two-wire protocol (variable
-speed, up to 400 kHz), with a high speed extension (3.4 MHz).  It provides
+a protocol developed by Philips. It is a two-wire protocol with variable
+speed (typically up to 400 kHz, high speed modes up to 5 MHz). It provides
 an inexpensive bus for connecting many types of devices with infrequent or
-low bandwidth communications needs.  I2C is widely used with embedded
-systems.  Some systems use variants that don't meet branding requirements,
+low bandwidth communications needs. I2C is widely used with embedded
+systems. Some systems use variants that don't meet branding requirements,
 and so are not advertised as being I2C but come under different names,
 e.g. TWI (Two Wire Interface), IIC.
 
-The latest official I2C specification is the `"I2C-bus specification and user
-manual" (UM10204) <https://www.nxp.com/webapp/Download?colCode=UM10204>`_
-published by NXP Semiconductors. However, you need to log-in to the site to
-access the PDF. An older version of the specification (revision 6) is archived
-`here <https://web.archive.org/web/20210813122132/https://www.nxp.com/docs/en/user-guide/UM10204.pdf>`_.
+The latest official I2C specification is the `"I²C-bus specification and user
+manual" (UM10204) <https://www.nxp.com/docs/en/user-guide/UM10204.pdf>`_
+published by NXP Semiconductors, version 7 as of this writing.
 
 SMBus (System Management Bus) is based on the I2C protocol, and is mostly
-a subset of I2C protocols and signaling.  Many I2C devices will work on an
+a subset of I2C protocols and signaling. Many I2C devices will work on an
 SMBus, but some SMBus protocols add semantics beyond what is required to
-achieve I2C branding.  Modern PC mainboards rely on SMBus.  The most common
+achieve I2C branding. Modern PC mainboards rely on SMBus. The most common
 devices connected through SMBus are RAM modules configured using I2C EEPROMs,
 and hardware monitoring chips.
 
 Because the SMBus is mostly a subset of the generalized I2C bus, we can
-use its protocols on many I2C systems.  However, there are systems that don't
+use its protocols on many I2C systems. However, there are systems that don't
 meet both SMBus and I2C electrical constraints; and others which can't
 implement all the common SMBus protocol semantics or messages.
 
 
 Terminology
 ===========
 
-Using the terminology from the official documentation, the I2C bus connects
-one or more *master* chips and one or more *slave* chips.
+The I2C bus connects one or more controller chips and one or more target chips.
 
 .. kernel-figure::  i2c_bus.svg
-   :alt:    Simple I2C bus with one master and 3 slaves
+   :alt:    Simple I2C bus with one controller and 3 targets
 
    Simple I2C bus
 
-A **master** chip is a node that starts communications with slaves. In the
-Linux kernel implementation it is called an **adapter** or bus. Adapter
-drivers are in the ``drivers/i2c/busses/`` subdirectory.
+A **controller** chip is a node that starts communications with targets. In the
+Linux kernel implementation it is also called an "adapter" or "bus". Controller
+drivers are usually in the ``drivers/i2c/busses/`` subdirectory.
 
-An **algorithm** contains general code that can be used to implement a
-whole class of I2C adapters. Each specific adapter driver either depends on
-an algorithm driver in the ``drivers/i2c/algos/`` subdirectory, or includes
-its own implementation.
+An **algorithm** contains general code that can be used to implement a whole
+class of I2C controllers. Each specific controller driver either depends on an
+algorithm driver in the ``drivers/i2c/algos/`` subdirectory, or includes its
+own implementation.
 
-A **slave** chip is a node that responds to communications when addressed
-by the master. In Linux it is called a **client**. Client drivers are kept
-in a directory specific to the feature they provide, for example
-``drivers/media/gpio/`` for GPIO expanders and ``drivers/media/i2c/`` for
+A **target** chip is a node that responds to communications when addressed by a
+controller. In the Linux kernel implementation it is also called a "client".
+While targets are usually separate external chips, Linux can also act as a
+target (needs hardware support) and respond to another controller on the bus.
+This is then called a **local target**. In contrast, an external chip is called
+a **remote target**.
+
+Target drivers are kept in a directory specific to the feature they provide,
+for example ``drivers/gpio/`` for GPIO expanders and ``drivers/media/i2c/`` for
 video-related chips.
 
-For the example configuration in figure, you will need a driver for your
-I2C adapter, and drivers for your I2C devices (usually one driver for each
-device).
+For the example configuration in the figure above, you will need one driver for
+the I2C controller, and drivers for your I2C targets. Usually one driver for
+each target.
+
+Synonyms
+--------
+
+As mentioned above, the Linux I2C implementation historically uses the terms
+"adapter" for controller and "client" for target. A number of data structures
+have these synonyms in their name. So, when discussing implementation details,
+you should be aware of these terms as well. The official wording is preferred,
+though.
+
+Outdated terminology
+--------------------
+
+In earlier I2C specifications, controller was named "master" and target was
+named "slave". These terms have been obsoleted with v7 of the specification and
+their use is also discouraged by the Linux Kernel Code of Conduct. You may
+still find them in references to documentation which has not been updated. The
+general attitude, however, is to use the inclusive terms: controller and
+target. Work to replace the old terminology in the Linux Kernel is on-going.

Documentation/i2c/summary.rst

@@ -123,8 +123,6 @@ operations:
       doc: dump pending nfsd rpc
       attribute-set: rpc-status
       dump:
-        pre: nfsd-nl-rpc-status-get-start
-        post: nfsd-nl-rpc-status-get-done
         reply:
           attributes:
             - xid

Documentation/netlink/specs/nfsd.yaml

@@ -32,6 +32,7 @@ Security-related interfaces
    seccomp_filter
    landlock
    lsm
+   mfd_noexec
    spec_ctrl
    tee
 

Documentation/userspace-api/index.rst

@@ -0,0 +1,86 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+==================================
+Introduction of non-executable mfd
+==================================
+:Author:
+    Daniel Verkamp <[email protected]>
+    Jeff Xu <[email protected]>
+
+:Contributor:
+	Aleksa Sarai <[email protected]>
+
+Since Linux introduced the memfd feature, memfds have always had their
+execute bit set, and the memfd_create() syscall doesn't allow setting
+it differently.
+
+However, in a secure-by-default system, such as ChromeOS, (where all
+executables should come from the rootfs, which is protected by verified
+boot), this executable nature of memfd opens a door for NoExec bypass
+and enables “confused deputy attack”.  E.g, in VRP bug [1]: cros_vm
+process created a memfd to share the content with an external process,
+however the memfd is overwritten and used for executing arbitrary code
+and root escalation. [2] lists more VRP of this kind.
+
+On the other hand, executable memfd has its legit use: runc uses memfd’s
+seal and executable feature to copy the contents of the binary then
+execute them. For such a system, we need a solution to differentiate runc's
+use of executable memfds and an attacker's [3].
+
+To address those above:
+ - Let memfd_create() set X bit at creation time.
+ - Let memfd be sealed for modifying X bit when NX is set.
+ - Add a new pid namespace sysctl: vm.memfd_noexec to help applications in
+   migrating and enforcing non-executable MFD.
+
+User API
+========
+``int memfd_create(const char *name, unsigned int flags)``
+
+``MFD_NOEXEC_SEAL``
+	When MFD_NOEXEC_SEAL bit is set in the ``flags``, memfd is created
+	with NX. F_SEAL_EXEC is set and the memfd can't be modified to
+	add X later. MFD_ALLOW_SEALING is also implied.
+	This is the most common case for the application to use memfd.
+
+``MFD_EXEC``
+	When MFD_EXEC bit is set in the ``flags``, memfd is created with X.
+
+Note:
+	``MFD_NOEXEC_SEAL`` implies ``MFD_ALLOW_SEALING``. In case that
+	an app doesn't want sealing, it can add F_SEAL_SEAL after creation.
+
+
+Sysctl:
+========
+``pid namespaced sysctl vm.memfd_noexec``
+
+The new pid namespaced sysctl vm.memfd_noexec has 3 values:
+
+ - 0: MEMFD_NOEXEC_SCOPE_EXEC
+	memfd_create() without MFD_EXEC nor MFD_NOEXEC_SEAL acts like
+	MFD_EXEC was set.
+
+ - 1: MEMFD_NOEXEC_SCOPE_NOEXEC_SEAL
+	memfd_create() without MFD_EXEC nor MFD_NOEXEC_SEAL acts like
+	MFD_NOEXEC_SEAL was set.
+
+ - 2: MEMFD_NOEXEC_SCOPE_NOEXEC_ENFORCED
+	memfd_create() without MFD_NOEXEC_SEAL will be rejected.
+
+The sysctl allows finer control of memfd_create for old software that
+doesn't set the executable bit; for example, a container with
+vm.memfd_noexec=1 means the old software will create non-executable memfd
+by default while new software can create executable memfd by setting
+MFD_EXEC.
+
+The value of vm.memfd_noexec is passed to child namespace at creation
+time. In addition, the setting is hierarchical, i.e. during memfd_create,
+we will search from current ns to root ns and use the most restrictive
+setting.
+
+[1] https://crbug.com/1305267
+
+[2] https://bugs.chromium.org/p/chromium/issues/list?q=type%3Dbug-security%20memfd%20escalation&can=1
+
+[3] https://lwn.net/Articles/781013/