gpio: tqmx86: introduce shadow register for GPIO output value

The TQMx86 GPIO controller uses the same register address for input and
output data. Reading the register will always return current inputs
rather than the previously set outputs (regardless of the current
direction setting). Therefore, using a RMW pattern does not make sense
when setting output values. Instead, the previously set output register
value needs to be stored as a shadow register.

As there is no reliable way to get the current output values from the
hardware, also initialize all channels to 0, to ensure that stored and
actual output values match. This should usually not have any effect in
practise, as the TQMx86 UEFI sets all outputs to 0 during boot.

Also prepare for extension of the driver to more than 8 GPIOs by using
DECLARE_BITMAP.

Fixes: b868db9 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://lore.kernel.org/r/d0555933becd45fa92a85675d26e4d59343ddc01.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <[email protected]>

Author: tq-schifferm

drivers/gpio/gpio-tqmx86.c

@@ -6,6 +6,7 @@
  *   Vadim V.Vlasov <[email protected]>
  */
 
+#include <linux/bitmap.h>
 #include <linux/bitops.h>
 #include <linux/errno.h>
 #include <linux/gpio/driver.h>
@@ -38,6 +39,7 @@ struct tqmx86_gpio_data {
 	void __iomem		*io_base;
 	int			irq;
 	raw_spinlock_t		spinlock;
+	DECLARE_BITMAP(output, TQMX86_NGPIO);
 	u8			irq_type[TQMX86_NGPI];
 };
 
@@ -64,15 +66,10 @@ static void tqmx86_gpio_set(struct gpio_chip *chip, unsigned int offset,
 {
 	struct tqmx86_gpio_data *gpio = gpiochip_get_data(chip);
 	unsigned long flags;
-	u8 val;
 
 	raw_spin_lock_irqsave(&gpio->spinlock, flags);
-	val = tqmx86_gpio_read(gpio, TQMX86_GPIOD);
-	if (value)
-		val |= BIT(offset);
-	else
-		val &= ~BIT(offset);
-	tqmx86_gpio_write(gpio, val, TQMX86_GPIOD);
+	__assign_bit(offset, gpio->output, value);
+	tqmx86_gpio_write(gpio, bitmap_get_value8(gpio->output, 0), TQMX86_GPIOD);
 	raw_spin_unlock_irqrestore(&gpio->spinlock, flags);
 }
 
@@ -277,6 +274,13 @@ static int tqmx86_gpio_probe(struct platform_device *pdev)
 
 	tqmx86_gpio_write(gpio, (u8)~TQMX86_DIR_INPUT_MASK, TQMX86_GPIODD);
 
+	/*
+	 * Reading the previous output state is not possible with TQMx86 hardware.
+	 * Initialize all outputs to 0 to have a defined state that matches the
+	 * shadow register.
+	 */
+	tqmx86_gpio_write(gpio, 0, TQMX86_GPIOD);
+
 	chip = &gpio->chip;
 	chip->label = "gpio-tqmx86";
 	chip->owner = THIS_MODULE;