KVM: arm64: Document vCPU feature selection UAPIs

KVM/arm64 has a couple schemes for handling vCPU feature selection now,
which is a lot to put on userspace. Add some documentation about how
these interact and provide some recommendations for how to use the
writable ID register scheme.

Reviewed-by: Marc Zyngier <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Oliver Upton <[email protected]>

Author: oupton

Documentation/virt/kvm/api.rst

@@ -3370,6 +3370,8 @@ return indicates the attribute is implemented.  It does not necessarily
 indicate that the attribute can be read or written in the device's
 current state.  "addr" is ignored.
 
+.. _KVM_ARM_VCPU_INIT:
+
 4.82 KVM_ARM_VCPU_INIT
 ----------------------
 
@@ -6070,6 +6072,8 @@ writes to the CNTVCT_EL0 and CNTPCT_EL0 registers using the SET_ONE_REG
 interface. No error will be returned, but the resulting offset will not be
 applied.
 
+.. _KVM_ARM_GET_REG_WRITABLE_MASKS:
+
 4.139 KVM_ARM_GET_REG_WRITABLE_MASKS
 -------------------------------------------
 

Documentation/virt/kvm/arm/index.rst

@@ -11,3 +11,4 @@ ARM
    hypercalls
    pvtime
    ptp_kvm
+   vcpu-features

Documentation/virt/kvm/arm/vcpu-features.rst

@@ -0,0 +1,48 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===============================
+vCPU feature selection on arm64
+===============================
+
+KVM/arm64 provides two mechanisms that allow userspace to configure
+the CPU features presented to the guest.
+
+KVM_ARM_VCPU_INIT
+=================
+
+The ``KVM_ARM_VCPU_INIT`` ioctl accepts a bitmap of feature flags
+(``struct kvm_vcpu_init::features``). Features enabled by this interface are
+*opt-in* and may change/extend UAPI. See :ref:`KVM_ARM_VCPU_INIT` for complete
+documentation of the features controlled by the ioctl.
+
+Otherwise, all CPU features supported by KVM are described by the architected
+ID registers.
+
+The ID Registers
+================
+
+The Arm architecture specifies a range of *ID Registers* that describe the set
+of architectural features supported by the CPU implementation. KVM initializes
+the guest's ID registers to the maximum set of CPU features supported by the
+system. The ID register values may be VM-scoped in KVM, meaning that the
+values could be shared for all vCPUs in a VM.
+
+KVM allows userspace to *opt-out* of certain CPU features described by the ID
+registers by writing values to them via the ``KVM_SET_ONE_REG`` ioctl. The ID
+registers are mutable until the VM has started, i.e. userspace has called
+``KVM_RUN`` on at least one vCPU in the VM. Userspace can discover what fields
+are mutable in the ID registers using the ``KVM_ARM_GET_REG_WRITABLE_MASKS``.
+See the :ref:`ioctl documentation <KVM_ARM_GET_REG_WRITABLE_MASKS>` for more
+details.
+
+Userspace is allowed to *limit* or *mask* CPU features according to the rules
+outlined by the architecture in DDI0487J.a D19.1.3 'Principles of the ID
+scheme for fields in ID register'. KVM does not allow ID register values that
+exceed the capabilities of the system.
+
+.. warning::
+   It is **strongly recommended** that userspace modify the ID register values
+   before accessing the rest of the vCPU's CPU register state. KVM may use the
+   ID register values to control feature emulation. Interleaving ID register
+   modification with other system register accesses may lead to unpredictable
+   behavior.