Merge pull request #966 from cyberman54/development

Development

Author: cyberman54

platformio_orig.ini

@@ -47,15 +47,15 @@ description = Paxcounter is a device for metering passenger flows in realtime. I
 
 [common]
 ; for release_version use max. 10 chars total, use any decimal format like "a.b.c"
-release_version = 3.5.0
+release_version = 3.6.0
 ; DEBUG LEVEL: For production run set to 0, otherwise device will leak RAM while running!
 ; 0=None, 1=Error, 2=Warn, 3=Info, 4=Debug, 5=Verbose
 debug_level = 3
 extra_scripts = pre:src/build.py
 otakeyfile = ota.conf
 lorakeyfile = loraconf.h
 lmicconfigfile = lmic_config.h
-platform_espressif32 = espressif32@6.0.1
+platform_espressif32 = espressif32@6.3.0
 monitor_speed = 115200
 upload_speed = 115200 ; set by build.py and taken from hal file
 lib_deps_lora =
@@ -92,19 +92,17 @@ lib_deps_all =
     ${common.lib_deps_gps}
     ${common.lib_deps_sensors}
     ${common.lib_deps_ledmatrix}
-build_flags_basic =
+build_flags_all =
     -include "src/paxcounter.conf"
-    '-DCORE_DEBUG_LEVEL=${common.debug_level}'
-    '-DLOG_LOCAL_LEVEL=${common.debug_level}'
-    '-DPROGVERSION="${common.release_version}"'
+    '-D CORE_DEBUG_LEVEL=${common.debug_level}'
+    '-D LOG_LOCAL_LEVEL=${common.debug_level}'
+    '-D PROGVERSION="${common.release_version}"'
     '-D LIBPAX_WIFI'
     '-D LIBPAX_BLE'
     '-D LIBPAX_ARDUINO'
-    '-DUSE_ESP_IDF_LOG'
-    '-DTAG=__FILE__'
-build_flags_all =
-    ${common.build_flags_basic}
-    -mfix-esp32-psram-cache-issue
+    '-D USE_ESP_IDF_LOG'
+    '-D TAG=__FILE__'
+    '-U BOARD_HAS_PSRAM'
 
 [env]
 framework = arduino

platformio_orig_s3.ini

@@ -10,15 +10,15 @@ description = Paxcounter is a device for metering passenger flows in realtime. I
 
 [common]
 ; for release_version use max. 10 chars total, use any decimal format like "a.b.c"
-release_version = 3.5.0
+release_version = 3.6.0
 ; DEBUG LEVEL: For production run set to 0, otherwise device will leak RAM while running!
 ; 0=None, 1=Error, 2=Warn, 3=Info, 4=Debug, 5=Verbose
 debug_level = 3
 extra_scripts = pre:src/build.py
 otakeyfile = ota.conf
 lorakeyfile = loraconf.h
 lmicconfigfile = lmic_config.h
-platform_espressif32 = espressif32@6.0.1
+platform_espressif32 = espressif32@6.3.0
 monitor_speed = 115200
 upload_speed = 115200 ; set by build.py and taken from hal file
 lib_deps_all =
@@ -31,19 +31,17 @@ lib_deps_all =
     mathertel/OneButton @ ^2.0.3
     256dpi/MQTT @ ^2.5.1
     ricmoo/QRCode @ ^0.0.1
-build_flags_basic =
+build_flags_all =
     -include "src/paxcounter.conf"
-    '-DCORE_DEBUG_LEVEL=${common.debug_level}'
-    '-DLOG_LOCAL_LEVEL=${common.debug_level}'
-    '-DPROGVERSION="${common.release_version}"'
+    '-D CORE_DEBUG_LEVEL=${common.debug_level}'
+    '-D LOG_LOCAL_LEVEL=${common.debug_level}'
+    '-D PROGVERSION="${common.release_version}"'
     '-D LIBPAX_WIFI'
     '-D LIBPAX_BLE'
     '-D LIBPAX_ARDUINO'
-    '-DUSE_ESP_IDF_LOG'
-    '-DTAG=__FILE__'
-build_flags_all =
-    ${common.build_flags_basic}
-    -mfix-esp32-psram-cache-issue
+    '-D USE_ESP_IDF_LOG'
+    '-D TAG=__FILE__'
+    '-U BOARD_HAS_PSRAM'
 
 [env]
 framework = arduino

src/display.cpp

@@ -142,7 +142,7 @@ void dp_init(bool verbose) {
 void dp_refresh(bool nextPage) {
   struct count_payload_t count; // libpax count storage
   static uint8_t DisplayPage = 0;
-  char timeState, strftime_buf[64];
+  char timeState, strftime_buf[45];
   time_t now;
   struct tm timeinfo = {0};
 #ifndef HAS_BUTTON

src/hal/generic.h

@@ -11,12 +11,12 @@
 // generic.h is kitchensink with all available options
 
 #define HAS_LORA 1 // comment out if device shall not send data via LoRa or has no LoRa
-#define HAS_SPI 1  // comment out if device shall not send data via SPI
+//#define HAS_SPI 1  // comment out if device shall not send data via SPI
 // pin definitions for SPI slave interface
-#define SPI_MOSI GPIO_NUM_23
-#define SPI_MISO GPIO_NUM_19
-#define SPI_SCLK GPIO_NUM_18
-#define SPI_CS   GPIO_NUM_5
+//#define SPI_MOSI GPIO_NUM_23
+//#define SPI_MISO GPIO_NUM_19
+//#define SPI_SCLK GPIO_NUM_18
+//#define SPI_CS   GPIO_NUM_5
 
 // enable only if you want to store a local paxcount table on the device
 #define HAS_SDCARD  1      // this board has an SD-card-reader/writer
@@ -35,9 +35,9 @@
 // for loading necessary libraries
 
 // BME680 sensor on I2C bus
-#define HAS_BME 1 // Enable BME sensors in general
-#define HAS_BME680 GPIO_NUM_21, GPIO_NUM_22 // SDA, SCL
-#define BME680_ADDR BME68X_I2C_ADDR_LOW // connect SDIO of BME680 to GND
+//#define HAS_BME 1 // Enable BME sensors in general
+//#define HAS_BME680 GPIO_NUM_21, GPIO_NUM_22 // SDA, SCL
+//#define BME680_ADDR BME68X_I2C_ADDR_LOW // connect SDIO of BME680 to GND
 
 // BME280 sensor on I2C bus
 //#define HAS_BME 1 // Enable BME sensors in general
@@ -49,10 +49,10 @@
 //#define BMP180_ADDR 0x77
 
 // SDS011 dust sensor settings
-#define HAS_SDS011 1 // use SDS011
+//#define HAS_SDS011 1 // use SDS011
 // used pins on the ESP-side:
-#define SDS_TX 19     // connect to RX on the SDS011
-#define SDS_RX 23     // connect to TX on the SDS011
+//#define SDS_TX 19     // connect to RX on the SDS011
+//#define SDS_RX 23     // connect to TX on the SDS011
 
 // up to three user defined sensors (if connected)
 //#define HAS_SENSOR_1 1 // comment out if device has user defined sensor #1
@@ -64,29 +64,29 @@
 //#define BOARD_HAS_PSRAM // use if board has external SPIRAM, note: this will reduce IRAM0 by 64KB for SPIRAM cache
 #define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
 
-#define HAS_DISPLAY 1
+//#define HAS_DISPLAY 1
 //#define MY_DISPLAY_FLIP  1 // use if display is rotated
 #define BAT_MEASURE_ADC ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
 #define BAT_VOLTAGE_DIVIDER 2 // voltage divider 100k/100k on board
 
 #define HAS_LED (21) // on board  LED
 #define HAS_BUTTON (39) // on board button
-#define RGB_LED_COUNT 1 // we have 1 LED
-#define HAS_RGB_LED FastLED.addLeds<WS2812, GPIO_NUM_0, GRB>(leds, RGB_LED_COUNT);
+//#define RGB_LED_COUNT 1 // we have 1 LED
+//#define HAS_RGB_LED FastLED.addLeds<WS2812, GPIO_NUM_0, GRB>(leds, RGB_LED_COUNT);
 
 // GPS settings
-#define HAS_GPS 1 // use on board GPS
-#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_12, GPIO_NUM_15 // UBlox NEO 6M RX, TX
-#define GPS_INT GPIO_NUM_13 // 30ns accurary timepulse, to be external wired on pcb: NEO 6M Pin#3 -> GPIO13
+//#define HAS_GPS 1 // use on board GPS
+//#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_12, GPIO_NUM_15 // UBlox NEO 6M RX, TX
+//#define GPS_INT GPIO_NUM_13 // 30ns accurary timepulse, to be external wired on pcb: NEO 6M Pin#3 -> GPIO13
 
 // Pins for I2C interface of OLED Display
-#define MY_DISPLAY_SDA (4)
-#define MY_DISPLAY_SCL (15)
-#define MY_DISPLAY_RST (16)
+//#define MY_DISPLAY_SDA (4)
+//#define MY_DISPLAY_SCL (15)
+//#define MY_DISPLAY_RST (16)
 
 // Settings for on board DS3231 RTC chip
-#define HAS_RTC MY_DISPLAY_SDA, MY_DISPLAY_SCL // SDA, SCL
-#define RTC_INT GPIO_NUM_34 // timepulse with accuracy +/- 2*e-6 [microseconds] = 0,1728sec / day
+//#define HAS_RTC MY_DISPLAY_SDA, MY_DISPLAY_SCL // SDA, SCL
+//#define RTC_INT GPIO_NUM_34 // timepulse with accuracy +/- 2*e-6 [microseconds] = 0,1728sec / day
 
 // Settings for IF482 interface
 //#define HAS_IF482 9600, SERIAL_7E1, GPIO_NUM_12, GPIO_NUM_14 // IF482 serial port parameters

src/hal/m5fire.h

@@ -1,7 +1,6 @@
 // clang-format off
 // upload_speed 921600
-// board m5stack-core-esp32
-// b0ard m5stack-fire -> does not compile due to IRAM0 shortage, because 64KB of 192KB used for caching external SPIRAM
+// board m5stack-fire
 
 // note use of GPIO16/17
 // https://www.bjoerns-techblog.de/2019/03/m5stack-fire-eine-uebersicht/
@@ -22,18 +21,18 @@
 #define LORA_IO2  LMIC_UNUSED_PIN
 
 // enable only if you want to store a local paxcount table on the device
-#define HAS_SDCARD  1      // this board has an SD-card-reader/writer
-#define SDCARD_CS    GPIO_NUM_4
-#define SDCARD_MOSI  MOSI
-#define SDCARD_MISO  MISO
-#define SDCARD_SCLK  SCK
+//#define HAS_SDCARD  1      // this board has an SD-card-reader/writer
+//#define SDCARD_CS    GPIO_NUM_4
+//#define SDCARD_MOSI  MOSI
+//#define SDCARD_MISO  MISO
+//#define SDCARD_SCLK  SCK
 
 #define CFG_sx1276_radio 1 // select LoRa chip
 #define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
 
 #define HAS_LED NOT_A_PIN // no on board LED (?)
-#define RGB_LED_COUNT 10 // M5fire has a stripe of 10 RGB Pixels
-#define HAS_RGB_LED FastLED.addLeds<SK6812, GPIO_NUM_15, GRB>(leds, RGB_LED_COUNT);
+//#define RGB_LED_COUNT 10 // M5fire has a stripe of 10 RGB Pixels
+//#define HAS_RGB_LED FastLED.addLeds<SK6812, GPIO_NUM_15, GRB>(leds, RGB_LED_COUNT);
 #define HAS_BUTTON (39) // on board button A
 
 // power management settings

src/lmic_config.h

@@ -106,4 +106,4 @@
 //#define USE_MBEDTLS_AES
 
 // Define this for devices with external power.
-//#define LMIC_MCMD_DEVS_BATT_DEFAULT MCMD_DEVS_EXT_POWER
+//#define LMIC_MCMD_DEVS_BATT_DEFAULT MCMD_DEVS_EXT_POWER