rfid not working with lgt8f328p minievb 3.3v

[Mohammad-Mahdi82]

Step 1: Describe your environment

• OS version: windows 11
• Arduino IDE version: latest
• MFRC522 Library version: latest
• Arduino device: Arduino lgt8f328p MiniEvb 3.3v
• MFRC522 device: RFID-RC522

Step 2: Describe the problem

I have an Arduino lgt8f328p MiniEvb 3.3v and it says: WARNING: Communication failure, is the MFRC522 properly connected?
My wiring is such as of an Arduino nano since NO PIN LAYOUTS FOR MINI HAS BEEN DOCUMENTED!

Steps to reproduce:

1. Get an Arduino pro mini
2. Try connecting it!

Observed Results:

• WARNING: Communication failure, is the MFRC522 properly connected?

Relevant Code:

  /*
 * ------------------------------------------------------------------------------------------------------------------
 * Example showing how to read data from a PICC to serial.
 * ------------------------------------------------------------------------------------------------------------------
 * This is a MFRC522 library example; for further details and other examples
 *  see: https://github.com/OSSLibraries/Arduino_MFRC522v2
 * 
 * Example sketch/program showing how to read data from a PICC (that is: a RFID Tag or Card) using
 *  a MFRC522 based RFID
 * Reader on the Arduino SPI interface.
 * 
 * When the Arduino and the MFRC522 module are connected (see the pin layout below), load this sketch into
 *  Arduino IDE
 * then verify/compile and upload it. To see the output: use Tools, Serial Monitor of the IDE (hit Ctrl+Shft+M). When
 * you present a PICC (that is: a RFID Tag or Card) at reading distance of the MFRC522 Reader/PCD, the serial output
 * will show the ID/UID, type and any data blocks it can read. Note: you may see "Timeout in communication" messages
 * when removing the PICC from reading distance too early.
 * 
 * If your reader supports it, this sketch/program will read all the PICCs presented (that is: multiple tag reading).
 * So if you stack two or more PICCs on top of each other and present them to the reader, it will first output all
 * details of the first and then the next PICC. Note that this may take some time as all data blocks are dumped, so
 * keep the PICCs at reading distance until complete.
 * 
 * @license Released into the public domain.
 * 
 * Typical pin layout used:
 * -----------------------------------------------------------------------------------------
 *             MFRC522      Arduino       Arduino   Arduino    Arduino          Arduino
 *             Reader/PCD   Uno/101       Mega      Nano v3    Leonardo/Micro   Pro Micro
 * Signal      Pin          Pin           Pin       Pin        Pin              Pin
 * -----------------------------------------------------------------------------------------
 * SPI SS      SDA(SS)      10            53        D10        10               10
 * SPI MOSI    MOSI         11 / ICSP-4   51        D11        ICSP-4           16
 * SPI MISO    MISO         12 / ICSP-1   50        D12        ICSP-1           14
 * SPI SCK     SCK          13 / ICSP-3   52        D13        ICSP-3           15
 *
 * Not found? For more see: https://github.com/OSSLibraries/Arduino_MFRC522v2#pin-layout
 */

#include <MFRC522v2.h>
#include <MFRC522DriverSPI.h>
//#include <MFRC522DriverI2C.h>
#include <MFRC522DriverPinSimple.h>
#include <MFRC522Debug.h>

MFRC522DriverPinSimple ss_pin(10); // Configurable, see typical pin layout above.

MFRC522DriverSPI driver{ss_pin}; // Create SPI driver.
//MFRC522DriverI2C driver{}; // Create I2C driver.
MFRC522 mfrc522{driver};  // Create MFRC522 instance.

void setup() {

  Serial.begin(9600);  // Initialize serial communications with the PC for debugging.
  while (!Serial);     // Do nothing if no serial port is opened (added for Arduinos based on ATMEGA32U4).
  mfrc522.PCD_Init();  // Init MFRC522 board.
  delay(4);
  MFRC522Debug::PCD_DumpVersionToSerial(mfrc522, Serial);	// Show details of PCD - MFRC522 Card Reader details.
	Serial.println(F("Scan PICC to see UID, SAK, type, and data blocks..."));
}

void loop() {
	// Reset the loop if no new card present on the sensor/reader. This saves the entire process when idle.
	if ( !mfrc522.PICC_IsNewCardPresent()) {
		return;
	}

	// Select one of the cards.
	if ( !mfrc522.PICC_ReadCardSerial()) {
		return;
	}

	// Dump debug info about the card; PICC_HaltA() is automatically called.
  MFRC522Debug::PICC_DumpToSerial(mfrc522, Serial, &(mfrc522.uid));
}