Help please #81

ondrom111 · 2025-03-14T12:09:01Z

ondrom111
Mar 14, 2025

I (211053) evse: Set enabled 1
I (211103) evse: Enter B2 state
I (211103) pilot: Set amp 84A*10 duty 136/1023
I (211103) ac_relay: Set relay: 0
W (223053) httpd_txrx: httpd_sock_err: error in recv : 104

Answered by ondrom111

Mar 15, 2025

Teraz som to skúšal na Renault ZOE a Tesle všetko OK. Tých Mitsubishi som mal viac a niektorý mi volali, ze s niektorými stojanmi nekomunikuje, asi to bude v komunikácii s autom. Prepáčte, ze som otravoval, ďakujem za pomoc. Ten projekt je super a ak niečo budete potrebovať otestovať kľudne napíšte. Ešte raz ďakujem a prajem pekný deň.

View full answer

dzurikmiroslav · 2025-03-14T12:48:04Z

dzurikmiroslav
Mar 14, 2025
Maintainer

This looks good

2 replies

ondrom111 Mar 14, 2025
Author

Ale nenabíja, iba keď vytiahnem kábel a znova zapojím, prečo?

dzurikmiroslav Mar 14, 2025
Maintainer

Nabijat ma v stave C2 a D2, v logu vidiet ze je v stave B2. Toto sa deje ked sa prerusi nabijanie a znova povoli?

ondrom111 · 2025-03-14T14:00:55Z

ondrom111
Mar 14, 2025
Author

Áno Dňa pi 14. 3. 2025, 14:55 Miroslav Dzúrik ***@***.***> napísal(a):

…

Nabijat ma v stave C2 a D2, v logu vidiet ze je v stave B2. Toto sa deje ked sa prerusi nabijanie a znova povoli? — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYJW62KOGXYMUHMHXPD2ULNUTAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENJQGEZTSOI> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12501399@ github.com>

1 reply

dzurikmiroslav Mar 14, 2025
Maintainer

A o ake auto sa jedna? Hodil by sa cely log od zaciatku pripojenia auta

ondrom111 · 2025-03-14T14:38:04Z

ondrom111
Mar 14, 2025
Author

Je to v podstate Mitsubishi I Miev alebo Citroen Czero a Peugeot ION, oni sú rovnaké. Mam ešte Renault ZOE a Teslu skúsim to aj tam. Ale neskôr Jedno ma moja v práci a druhé je na zdviháku. Ešte keď v nastaveniach, systém vypnem a zapnem nabíjačka dostupná, tak to ide. pi 14. 3. 2025 o 15:06 Miroslav Dzúrik ***@***.***> napísal(a):

A o ake auto sa jedna? Hodil by sa cely log od zaciatku pripojenia auta — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYNLVA2H5XH4ZX42FA32ULPABAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENJQGE2TKMI> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12501551@ github.com>

I (594) app_main: Running partition: app1 I (644) app_main: File system partition total size: 327680, used: 24576 I (684) wifi:wifi driver task: 3ffc3d48, prio:23, stack:6656, core=0 I (684) wifi:wifi firmware version: 48ea317a7 I (684) wifi:wifi certification version: v7.0 I (684) wifi:config NVS flash: enabled I (684) wifi:config nano formatting: disabled I (684) wifi:Init data frame dynamic rx buffer num: 32 I (684) wifi:Init static rx mgmt buffer num: 5 I (684) wifi:Init management short buffer num: 32 I (684) wifi:Init dynamic tx buffer num: 32 I (684) wifi:Init static rx buffer size: 1600 I (684) wifi:Init static rx buffer num: 10 I (684) wifi:Init dynamic rx buffer num: 32 I (684) wifi_init: rx ba win: 6 I (694) wifi_init: accept mbox: 6 I (694) wifi_init: tcpip mbox: 32 I (694) wifi_init: udp mbox: 6 I (694) wifi_init: tcp mbox: 6 I (694) wifi_init: tcp tx win: 5760 I (694) wifi_init: tcp rx win: 5760 I (694) wifi_init: tcp mss: 1440 I (694) wifi_init: WiFi IRAM OP enabled I (694) wifi_init: WiFi RX IRAM OP enabled W (694) wifi:Password length matches WPA2 standards, authmode threshold changes from OPEN to WPA2 I (694) phy_init: phy_version 4840,02e0d70,Sep 2 2024,19:39:07 I (764) wifi:mode : sta (94:b9:7e:d9:7a:d8) I (764) wifi:enable tsf I (774) adc: Calibration scheme version is Line Fitting I (774) wifi: STA start I (774) gpio: GPIO[26]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 I (1034) wifi:new:<1,1>, old:<1,0>, ap:<255,255>, sta:<1,1>, prof:1, snd_ch_cfg:0x0 I (1034) wifi:state: init -> auth (0xb0) I (1034) wifi:state: auth -> init (0x8a0) I (1034) wifi:new:<1,0>, old:<1,1>, ap:<255,255>, sta:<1,1>, prof:1, snd_ch_cfg:0x0 I (1034) wifi: STA disconnected I (1074) energy_meter: Current zero 1670.713257 0.000000 0.000000 I (1114) energy_meter: Voltage zero 1676.165283 0.000000 0.000000 I (1114) gpio: GPIO[17]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 I (1114) gpio: GPIO[18]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 I (1114) gpio: GPIO[19]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 I (1114) gpio: GPIO[16]| InputEn: 0| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 I (1134) temp_sensor: Found 1 sensors I (1134) serial_logger: Starting on uart 0 I (1144) serial_nextion: Starting on uart 2 I (1144) rest: Starting server on port: 80 I (1154) pilot: Set level 1 I (1154) gpio: GPIO[0]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:3 I (1154) script: Starting script E (1264) esp-tls: [sock=51] connect() error: Host is unreachable E (1264) transport_base: Failed to open a new connection: 32772 E (1264) mqtt_client: Error transport connect I (1274) evse: Enter B1 state I (1274) ac_relay: Set relay: 0 I (1274) energy_meter: Start session I (1334) evse: Enter B2 state I (1334) pilot: Set amp 91A*10 duty 153/1023 I (1334) ac_relay: Set relay: 0 I (3464) wifi: STA disconnected I (3474) wifi:new:<1,1>, old:<1,0>, ap:<255,255>, sta:<1,1>, prof:1, snd_ch_cfg:0x0 I (3474) wifi:state: init -> auth (0xb0) I (3474) wifi:state: auth -> assoc (0x0) I (3484) wifi:state: assoc -> run (0x10) I (3514) wifi:connected with ANDREJ ADMIN, aid = 1, channel 1, 40U, bssid = 00:13:ef:b2:6e:9a I (3514) wifi:security: WPA2-PSK, phy: bgn, rssi: -50 I (3514) wifi:pm start, type: 1 I (3514) wifi:dp: 1, bi: 102400, li: 3, scale listen interval from 307200 us to 307200 us I (3524) wifi:<ba-add>idx:0 (ifx:0, 00:13:ef:b2:6e:9a), tid:6, ssn:2, winSize:64 I (3564) wifi:AP's beacon interval = 102400 us, DTIM period = 1 I (4534) esp_netif_handlers: sta ip: 192.168.1.140, mask: 255.255.255.0, gw: 192.168.1.1 I (4534) wifi: WiFi STA got ip: 192.168.1.140 I (4664) wifi:<ba-add>idx:1 (ifx:0, 00:13:ef:b2:6e:9a), tid:0, ssn:1, winSize:64 W (14354) httpd_txrx: httpd_sock_err: error in send : 104 W (14354) httpd_txrx: httpd_sock_err: error in recv : 104

4 replies

dzurikmiroslav Mar 14, 2025
Maintainer

Tu predpokladam ze auto bolo zapojene a cely log je od rebootu/startu EVSE? Aka je schema zapojenia? Nieco vlastne alebo ESP32DevkitC EVSE ?

ondrom111 Mar 15, 2025
Author

ESP32DevkitC EVSE

ondrom111 Mar 15, 2025
Author

Teraz som to skúšal na Renault ZOE a Tesle všetko OK. Tých Mitsubishi som mal viac a niektorý mi volali, ze s niektorými stojanmi nekomunikuje, asi to bude v komunikácii s autom. Prepáčte, ze som otravoval, ďakujem za pomoc. Ten projekt je super a ak niečo budete potrebovať otestovať kľudne napíšte. Ešte raz ďakujem a prajem pekný deň.

Answer selected by dzurikmiroslav

dzurikmiroslav Mar 19, 2025
Maintainer

Vdaka za info :) ja som to zatial skusal na: BMW i3, Enyaq a eUp.
Co sa tyka Mitsubishi, chcelo by to s osciloskopom merat priebehy napatia na CP v jednotlivych stavoch. Je mozne ze pre jednotlive stavy maju trochu inac nastavene napatove urovne. Alebo nerataju s puauzovanim nabijania.

ondrom111 · 2025-03-19T07:42:24Z

ondrom111
Mar 19, 2025
Author

Ešte jedna otázka keď prepnem z trojfazoveho na jednofazový alebo naopak, stále musim reštartovať? Alebo mám niekde chybu? Dňa st 19. 3. 2025, 8:37 Miroslav Dzúrik ***@***.***> napísal(a):

…

Vdaka za info :) ja som to zatial skusal na: BMW i3, Enyaq a eUp. Co sa tyka Mitsubishi, chcelo by to s osciloskopom merat priebehy napatia na CP v jednotlivych stavoch. Je mozne ze pre jednotlive stavy maju trochu inac nastavene napatove urovne. Alebo nerataju s puauzovanim nabijania. — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYLSNQZXE4G7X5CXWO32VENDRAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENJUG44DAMI> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12547801@ github.com>

1 reply

dzurikmiroslav Mar 19, 2025
Maintainer

Zatial som neskusal prepinat pocas nabijania, viem ze existuju take wallboxy ale zatial sa mi nepodarilo zistit ako to maju implementovane. Myslim ze je potrebna pauza, pockat kym odpoji stykac a potom pripojit/odpojit L2 a L3...
A ako je to riesene? L2 a L3 su na samostatnom stykaci?

ondrom111 · 2025-03-19T07:51:55Z

ondrom111
Mar 19, 2025
Author

Nemyslím počas nabíjania, ale pred alebo po. Dňa st 19. 3. 2025, 8:50 Miroslav Dzúrik ***@***.***> napísal(a):

…

Zatial som neskusal prepinat pocas nabijania, viem ze existuju take wallboxy ale zatial sa mi nepodarilo zistit ako to maju implementovane. Myslim ze je potrebna pauza, pockat kym odpoji stykac a potom pripojit/odpojit L2 a L3... A ako je to riesene? L2 a L3 su na samostatnom stykaci? — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYPS45R4CM3E6R4EPYT2VEOSTAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENJUG44TENY> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12547927@ github.com>

0 replies

ondrom111 · 2025-03-19T07:53:20Z

ondrom111
Mar 19, 2025
Author

Áno mám dva stykače jeden na F1 a N a druhý na F2 a F3 Dňa st 19. 3. 2025, 8:51 ANDREJ MITERA ***@***.***> napísal(a):

…

Nemyslím počas nabíjania, ale pred alebo po. Dňa st 19. 3. 2025, 8:50 Miroslav Dzúrik ***@***.***> napísal(a): > Zatial som neskusal prepinat pocas nabijania, viem ze existuju take > wallboxy ale zatial sa mi nepodarilo zistit ako to maju implementovane. > Myslim ze je potrebna pauza, pockat kym odpoji stykac a potom > pripojit/odpojit L2 a L3... > A ako je to riesene? L2 a L3 su na samostatnom stykaci? > > — > Reply to this email directly, view it on GitHub > <#81 (reply in thread)>, > or unsubscribe > <https://github.com/notifications/unsubscribe-auth/AN5VPYPS45R4CM3E6R4EPYT2VEOSTAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENJUG44TENY> > . > You are receiving this because you are subscribed to this thread.Message > ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12547927@ > github.com> >

1 reply

dzurikmiroslav Mar 19, 2025
Maintainer

To by nemal byt problem, ked je hlavny stykac k autu odpojeny, tak sa moze hocikedy odpojit/propojit F2 a F3.

ondrom111 · 2025-03-19T08:01:40Z

ondrom111
Mar 19, 2025
Author

Myslim prepinanie 3f elektromera na 1f st 19. 3. 2025 o 8:59 Miroslav Dzúrik ***@***.***> napísal(a):

…

To by nemal byt problem, ked je hlavny stykac k autu odpojeny, tak sa moze hocikedy odpojit/propojit F2 a F3. — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYK73M7H34Z2R3WVXND2VEPVPAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENJUHAYDINY> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12548047@ github.com>

1 reply

dzurikmiroslav Mar 19, 2025
Maintainer

Aha, ale doska ESP32DevkitC EVSE vstup pre meranie jednej fazy. Ci Elektromer je v akom Rezime, Fiktivny?

ondrom111 · 2025-03-19T08:11:16Z

ondrom111
Mar 19, 2025
Author

nie meranie prúdu, ale upravil som energyMeter: currentAdcChannels: [7, 7, 7] currentScale: 0.759091 voltageAdcChannels: [6, 6, 6] voltageScale: 0.47 môže to tak byť? st 19. 3. 2025 o 9:07 Miroslav Dzúrik ***@***.***> napísal(a):

…

Aha, ale doska ESP32DevkitC EVSE vstup pre meranie jednej fazy. Ci Elektromer je v akom Rezime, Fiktivny? — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYMFU3BC73ZVGYTR3RD2VEQTXAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENJUHAYTEOI> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12548129@ github.com>

1 reply

dzurikmiroslav Mar 19, 2025
Maintainer

Toto asi nie je schodne, ten isty ADC kanal by sa nemal viac krat pouzivat.

Ked sa nastavi Trojfázový tak namerane hodnoty na L1 by mal pouzit tiez pre L2 a L3.

ondrom111 · 2025-03-19T08:21:26Z

ondrom111
Mar 19, 2025
Author

ale ked to nemam takto tak mi ho neprepne do trojfazoveho ani po restarte. Stale mam v "o systemu" trojfazovy elektromer !nie! st 19. 3. 2025 o 9:15 Miroslav Dzúrik ***@***.***> napísal(a):

…

Toto asi nie je schodne, ten isty ADC kanal by sa nemal viac krat pouzivat. image.png (view on web) <https://github.com/user-attachments/assets/1982f251-6943-4dad-a6de-7d3c43b2f8ed> Ked sa nastavi *Trojfázový* tak namerane hodnoty na L1 by mal pouzit tiez pre L2 a L3. — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYLLK4JTMXO7RR5BU6L2VERRZAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENJUHAYTSOA> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12548198@ github.com>

1 reply

dzurikmiroslav Mar 19, 2025
Maintainer

V o systeme sa zabrazuje konfiguraciu HW. To nevadi ze sa to tam zobrazuje jednofazovy.
Podstatne je co je v nastavenie nabijania. Potom by mal na hlavnej obrazovke pocas nabijania zobrazovat aj udaje z L2 a L3.

ondrom111 · 2025-03-19T08:31:14Z

ondrom111
Mar 19, 2025
Author

Ja mam v HA zobrazovanie boardconfig.energymeterthreephases a tam mi to tým pádom neprepne relé na spínanie oboch stýkačov súčasne st 19. 3. 2025 o 9:25 Miroslav Dzúrik ***@***.***> napísal(a):

…

V o systeme sa zabrazuje konfiguraciu HW. To nevadi ze sa to tam zobrazuje jednofazovy. Podstatne je co je v nastavenie nabijania. Potom by mal na hlavnej obrazovke pocas nabijania zobrazovat aj udaje z L2 a L3. — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYPIASF655WT6YPXDJ32VESYXAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENJUHAZTCNQ> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12548316@ github.com>

1 reply

dzurikmiroslav Mar 19, 2025
Maintainer

Asi uz rozumiem, v Lua potrebujete zistit ake je nastvenie elektromera, momentalne pre to nie je v Lua API...
Da sa zavolat evse.getvoltage a zisti ci su posledne dve hodnoty nulove, ale to funguje len pocas nabijania auta.
Mozem v Lua evse modul rozsirit o parametre z elektromera, v dalsom release...

ondrom111 · 2025-03-19T08:40:45Z

ondrom111
Mar 19, 2025
Author

Ok ďakujem 👍 Dňa st 19. 3. 2025, 9:38 Miroslav Dzúrik ***@***.***> napísal(a):

…

Asi uz rozumiem, v Lua potrebujete zistit ake je nastvenie elektromera, momentalne pre to nie je v Lua API... Da sa zavolat evse.getvoltage a zisti ci su posledne dve hodnoty nulove, ale to funguje len pocas nabijania auta. Mozem v Lua evse modul rozsirit o parametre z elektromera, v dalsom release... — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYNAAWBGAY3LDMKUF3D2VEUHFAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENJUHA2DKNA> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12548454@ github.com>

0 replies

ondrom111 · 2025-03-19T11:03:38Z

ondrom111
Mar 19, 2025
Author

ešte jeden dotaz, ak by nebol problém upravit. Ak nastavím nabíjací prúd v HA na väčší alebo menší tak na webe bude zobrazovat stále ten co bol predtým dokedy nerefresnem stranku. st 19. 3. 2025 o 9:40 ANDREJ MITERA ***@***.***> napísal(a):

…

Ok ďakujem 👍 Dňa st 19. 3. 2025, 9:38 Miroslav Dzúrik ***@***.***> napísal(a): > Asi uz rozumiem, v Lua potrebujete zistit ake je nastvenie elektromera, > momentalne pre to nie je v Lua API... > Da sa zavolat evse.getvoltage a zisti ci su posledne dve hodnoty nulove, > ale to funguje len pocas nabijania auta. > Mozem v Lua evse modul rozsirit o parametre z elektromera, v dalsom > release... > > — > Reply to this email directly, view it on GitHub > <#81 (reply in thread)>, > or unsubscribe > <https://github.com/notifications/unsubscribe-auth/AN5VPYNAAWBGAY3LDMKUF3D2VEUHFAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENJUHA2DKNA> > . > You are receiving this because you are subscribed to this thread.Message > ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12548454@ > github.com> >

3 replies

dzurikmiroslav Mar 20, 2025
Maintainer

Tu som prave chcel nech vzdy zobrazuje aktualnu hodnotu

ondrom111 Mar 20, 2025
Author

Ale ak je cez web a HA mi zmeni z 20A na 10A tak webove rozhranie stale ukazuje 20A ale nabija iba 10A ked urobim refresh stranky tak uz ukazuje 10A ako ma. Zapinanie a vypinanie nabijania sa prepina pekne samo ked vypnem v HA tak ho vypne aj na webe.

dzurikmiroslav Mar 20, 2025
Maintainer

Aha, to som si nevsimol, malo by to zmenit, preverim to...

ondrom111 · 2025-04-11T11:29:04Z

ondrom111
Apr 11, 2025
Author

Dal som na lan kabel feritove jadra, lan kabel ide spolu s 240v kablami sice je cat6, ale pre istotu.
zatial to vyzera dobre, este keby sa dalo nastavovat cez lua aj zap, a vypinanie trojfazoveho rezimu aby som si mohol spravit automatizaciu. a idealne by bolo aspon pre mna, keby sa cez lua dalo zap. a vyp. nabijacka dostupna., mam jedno auto ktore ked zastavim nabijanie a spustim uz sa nenabija musim vytiahnut nab. kabel. ale ked vypnem a zapnem nabijacka dostupna tak sa nabija. urobil by som v HA automatizaciu a ta by to poriesila.

4 replies

dzurikmiroslav Apr 11, 2025
Maintainer

Nabijacka dosutpna sa da cez Lua ovladat evse.getavailable / evse.setavailable
Mozem doplnit aj metodu energymeters.setthreephases, ale treba mysliet na to, ze tento parameter je perzistentny (ulozene v NVS pamati ESP32)

dzurikmiroslav Apr 11, 2025
Maintainer

S HA zatial nemam ziadnu skusenost, ale bolo by fajn kebyze zverejnite vas plugin githube. Lebo dost ludi prave toto riesi :)

ondrom111 Apr 11, 2025
Author

nevsimol som si ze je tam moznost evse.setavailable teraz som ju dorobil, tu takisto treba refresnut stranku ale to nevadi to sa tak casto nepouziva. a mozme tykat nech sa lepsie pise? mozem niekde dat lua subor na kontrolu? ak je vsetko ok dam tu vsetko co som urobil aj komunikaciu s HA

ondrom111 Apr 12, 2025
Author

DAM SUBOR LUA TU AK BUDETE MAT CAS TAK MRKNITE CI TO TAK MOZE BYT?

local evse = require("evse")
local mqtt = require("mqtt")
local json = require("json")
local boardconfig = require("boardconfig")
local energymeter = require("energymeter")

return {
id = "homeassistant_evse1",
name = "Home Assistant MQTT Connector - EVSE1",
description = "MQTT connector for Home Assistant - EVSE1",
params = {
username = { type = "string", name = "MQTT Username" },
password = { type = "string", name = "MQTT Password" }
},
start = function(params)
print("Spúšťam Home Assistant MQTT konektor pre EVSE1...")

    -- Kontrola, či sú parametre username a password nastavené
    if not params.username or not params.password then
        print("Chyba: MQTT prihlasovacie údaje nie sú nastavené!")
        return
    end

    -- Vytvorenie MQTT klienta s prihlasovacími údajmi
    local client = mqtt.client("mqtt://192.168.1.59:1883", params.username, params.password, { client_id = "evse1" })

    -- Vytvorenie korutiny pre pripojenie k brokeru
    return coroutine.create(function()
        local connected = false
        repeat
            print("Pokúšam sa pripojiť k MQTT brokeru...")
            connected = client:connect()
            if not connected then
                print("Nepodarilo sa pripojiť k MQTT brokeru. Skúšam znova za 1 sekundu...")
                os.execute("sleep 1")  -- Počkaj 1 sekundu pred ďalším pokusom
            end
        until connected
        print("Úspešne pripojené k MQTT brokeru!")

        -- Odber správ z témy evse1/cmd
        client:subscribe("evse1/cmd", function(topic, data)
            local payload = json.decode(data)

            if payload.method == "charger_enable" then
                evse.setenabled(payload.param)
            elseif payload.method == "setCurrent" then
                evse.setchargingcurrent(payload.param)
            elseif payload.method == "setconsumptionlimit" then
                evse.setconsumptionlimit(payload.param)
            elseif payload.method == "setchargingtimelimit" then
                evse.setchargingtimelimit(payload.param)
            elseif payload.method == "setunderpowerlimit" then
                evse.setunderpowerlimit(payload.param)
            elseif payload.method == "setavailable" then
                evse.setavailable(payload.param)
            end
        end)

        -- Funkcia na odoslanie stavu EVSE1 cez MQTT
        function send()
            local payload = {}
            local state = evse.getstate()

            -- Základné informácie o stave EVSE1
            payload["session"] = state >= evse.STATEB1 and state <= evse.STATED2 and 1 or 0
            payload["charging"] = state == evse.STATEC2 or state == evse.STATED2 and 1 or 0
            payload["enabled"] = evse.getenabled() and 1 or 0
            payload["available"] = evse.getavailable() and 1 or 0
            payload["error"] = evse.geterror() > 0
            payload["consumption"] = evse.getconsumption() or energymeter.getconsumption()
            payload["power"] = evse.getpower() or energymeter.getpower()
            payload["uptime"] = os.clock()
            
            -- Teplotné senzory
            payload["getlowtemperature"] = evse.getlowtemperature()
            payload["gethightemperature"] = evse.gethightemperature()
            
            -- Limitné hodnoty
            payload["getconsumptionlimit"] = evse.getconsumptionlimit()
            payload["getchargingtimelimit"] = evse.getchargingtimelimit()
            payload["getunderpowerlimit"] = evse.getunderpowerlimit()
            payload["getdefaultconsumptionlimit"] = evse.getdefaultconsumptionlimit()
            payload["getdefaultchargingtimelimit"] = evse.getdefaultchargingtimelimit()
            payload["getdefaultunderpowerlimit"] = evse.getdefaultunderpowerlimit()
            
            -- Meranie prúdu a napätia
            local currentL1, currentL2, currentL3 = energymeter.getcurrent()
            local voltageL1, voltageL2, voltageL3 = energymeter.getvoltage()
            
            payload["currentL1"] = math.floor((currentL1 or evse.getcurrent()) * 10 + 0.5) / 10
            payload["currentL2"] = math.floor((currentL2 or 0) * 10 + 0.5) / 10
            payload["currentL3"] = math.floor((currentL3 or 0) * 10 + 0.5) / 10
            payload["voltageL1"] = math.floor((voltageL1 or evse.getvoltage()) * 10 + 0.5) / 10
            payload["voltageL2"] = math.floor((voltageL2 or 0) * 10 + 0.5) / 10
            payload["voltageL3"] = math.floor((voltageL3 or 0) * 10 + 0.5) / 10
            
            -- Časové údaje
            payload["session_time"] = evse.getsessiontime() or energymeter.getsessiontime()
            payload["current_configured"] = evse.getchargingcurrent()
            payload["charging_time"] = energymeter.getchargingtime()
            
            -- Ďalšie údaje
            payload["ac_voltage"] = energymeter.getacvoltage()
            payload["three_phases"] = energymeter.getthreephases()
            payload["energymeter_mode"] = energymeter.getmode()

            -- Odoslanie dát cez MQTT
            client:publish("evse1/status", json.encode(payload))
        end

        local counter = 0

        while true do
            if counter == 10 then
                send()
                counter = 0
            end
            counter = counter + 1
            coroutine.yield(1000)
        end
    end)  -- Koniec coroutine.create
end  -- Koniec funkcie start

} -- Koniec návratového objektu

ondrom111 · 2025-04-12T07:17:18Z

ondrom111
Apr 12, 2025
Author

a este ten problem z wifi ak budete mat cas
I (36267576) ac_relay: Set relay: 1
I (36296256) evse: Enter B2 state
I (36296256) ac_relay: Set relay: 0
I (36313946) evse: Set available 0
I (36313986) evse: Enter F state
I (36313986) pilot: Set level 0
I (36313986) ac_relay: Set relay: 0
I (36313986) energy_meter: Stop session
I (37076796) wifi:new:<6,0>, old:<6,1>, ap:<255,255>, sta:<6,0>, prof:1, snd_ch_cfg:0x0
I (37077816) wifi:new:<6,1>, old:<6,0>, ap:<255,255>, sta:<6,1>, prof:1, snd_ch_cfg:0x0
I (37676886) wifi:new:<6,0>, old:<6,1>, ap:<255,255>, sta:<6,0>, prof:1, snd_ch_cfg:0x0
I (37677916) wifi:new:<6,1>, old:<6,0>, ap:<255,255>, sta:<6,1>, prof:1, snd_ch_cfg:0x0
I (37706896) wifi:new:<6,0>, old:<6,1>, ap:<255,255>, sta:<6,0>, prof:1, snd_ch_cfg:0x0
I (37707916) wifi:new:<6,1>, old:<6,0>, ap:<255,255>, sta:<6,1>, prof:1, snd_ch_cfg:0x0
I (38306886) wifi:new:<6,0>, old:<6,1>, ap:<255,255>, sta:<6,0>, prof:1, snd_ch_cfg:0x0
I (38308016) wifi:new:<6,1>, old:<6,0>, ap:<255,255>, sta:<6,1>, prof:1, snd_ch_cfg:0x0
W (42424536) temp_sensor: Measure error 264 (ESP_ERR_INVALID_RESPONSE)
I (58107086) wifi:new:<6,0>, old:<6,1>, ap:<255,255>, sta:<6,0>, prof:1, snd_ch_cfg:0x0
I (58108006) wifi:new:<6,1>, old:<6,0>, ap:<255,255>, sta:<6,1>, prof:1, snd_ch_cfg:0x0
I (59997186) wifi:new:<6,0>, old:<6,1>, ap:<255,255>, sta:<6,0>, prof:1, snd_ch_cfg:0x0
I (59998106) wifi:new:<6,1>, old:<6,0>, ap:<255,255>, sta:<6,1>, prof:1, snd_ch_cfg:0x0
I (60027196) wifi:new:<6,0>, old:<6,1>, ap:<255,255>, sta:<6,0>, prof:1, snd_ch_cfg:0x0
I (60028116) wifi:new:<6,1>, old:<6,0>, ap:<255,255>, sta:<6,1>, prof:1, snd_ch_cfg:0x0
I (63087286) wifi:new:<6,0>, old:<6,1>, ap:<255,255>, sta:<6,0>, prof:1, snd_ch_cfg:0x0
I (63088316) wifi:new:<6,1>, old:<6,0>, ap:<255,255>, sta:<6,1>, prof:1, snd_ch_cfg:0x0
I (65397466) wifi:new:<6,0>, old:<6,1>, ap:<255,255>, sta:<6,0>, prof:1, snd_ch_cfg:0x0
I (65398486) wifi:new:<6,1>, old:<6,0>, ap:<255,255>, sta:<6,1>, prof:1, snd_ch_cfg:0x0
I (65517486) wifi:new:<6,0>, old:<6,1>, ap:<255,255>, sta:<6,0>, prof:1, snd_ch_cfg:0x0
I (65518506) wifi:new:<6,1>, old:<6,0>, ap:<255,255>, sta:<6,1>, prof:1, snd_ch_cfg:0x0
I (66357526) wifi:new:<6,0>, old:<6,1>, ap:<255,255>, sta:<6,0>, prof:1, snd_ch_cfg:0x0
I (66358546) wifi:new:<6,1>, old:<6,0>, ap:<255,255>, sta:<6,1>, prof:1, snd_ch_cfg:0x0
I (66387526) wifi:new:<6,0>, old:<6,1>, ap:<255,255>, sta:<6,0>, prof:1, snd_ch_cfg:0x0
I (66388556) wifi:new:<6,1>, old:<6,0>, ap:<255,255>, sta:<6,1>, prof:1, snd_ch_cfg:0x0
W (66616446) httpd_txrx: httpd_sock_err: error in recv : 113

0 replies

dzurikmiroslav · 2025-04-12T19:01:25Z

dzurikmiroslav
Apr 12, 2025
Maintainer

Jasne, mozeme si tykat :)
Pozeram ten script, je tam par chyb, napr. pri inicializacii mqtt klienta sa neda definovat client_id, je to potrebne pre idetifikaciu klienta?
Dalej os.execute("sleep 1") neurobi nic, kedze to nie je linux :)
Trochu to odladim, urobim viac definovatelne parametre a pridam do wiki...
Na to WiFi sa pozriem, je mozne ze nestrati WiFi pripojenie, len prestane reagovat http porte...

4 replies

ondrom111 Apr 12, 2025
Author

ano bez client_id sa to neprihlasi. ked toto bude hotove a nebudu tam velke zmeny mozem ti dat aj mqtt.yaml z HA. daj si ho na wiki ak chces

ondrom111 Apr 12, 2025
Author

a teraz s tym novym mi to wifi drzi uz 2 den. mozno to uz bude dobre.

ondrom111 Apr 12, 2025
Author

este jedna otazka ma napadla neviem ci dobre pozeram, ale nevidim tam celkovu spotrebu, ta by do HA energie sa zisla

dzurikmiroslav Apr 12, 2025
Maintainer

ano, zatial to tam nie je, pridam to...

ondrom111 · 2025-04-17T12:41:50Z

ondrom111
Apr 17, 2025
Author

DNES SOM SKUSAL NABIJAT TESLU ALE NECHCE TO NABIJAT VSETKY LIMITY AJ RELACIE ZIADNE, ELEKTROMER JEDNOFAZOVY FIKTIVNY.
A NECHCE NABIJAT. NAINSTALOVAL SOM NANOVO FIRMWARE. NECHAL SOM TO BEZ MQTT TAK AKO BOLA NA UPLNOM ZACIATKU A TO ISTE NENABIJA.

I (282640) evse: Enter A state
I (282640) pilot: Set level 1
I (282640) ac_relay: Set relay: 0
I (282640) energy_meter: Stop session
I (282700) evse: Enter B1 state
I (282700) ac_relay: Set relay: 0
I (282700) energy_meter: Start session
I (282760) evse: Enter B2 state
I (282760) pilot: Set amp 220A*10 duty 374/1023
I (282760) ac_relay: Set relay: 0
I (293970) evse: Enter A state
I (293970) pilot: Set level 1
I (293970) ac_relay: Set relay: 0
I (293970) energy_meter: Stop session

1 reply

dzurikmiroslav Apr 17, 2025
Maintainer

To je prvy krat co si skusal pripojit Teslu? Ci niekedy to chodilo?

ondrom111 · 2025-04-17T12:52:57Z

ondrom111
Apr 17, 2025
Author

Pri staršej verzii isla Dňa št 17. 4. 2025, 14:47 Miroslav Dzúrik ***@***.***> napísal(a):

…

To je prvy krat co si skusal pripojit Teslu? Ci niekedy to chodilo? — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYLU7GSPRRWD7M23VEL2Z6PGPAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTEOBWG4YTAMY> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12867103@ github.com>

1 reply

dzurikmiroslav Apr 17, 2025
Maintainer

Z logu to vyzera auto naprv zistilo aky je nabijaci prud a potom si to rozmyslelo, ne je v aute nahodou nastaveny casovy plan kedy sa ma nabijat?

ondrom111 · 2025-04-17T13:01:29Z

ondrom111
Apr 17, 2025
Author

NIE NEMAM ZIADNE OBMEDZENIA A DAL SOM OBYCAJNU NABIJACKU A TA NABIJA št 17. 4. 2025 o 14:59 Miroslav Dzúrik ***@***.***> napísal(a):

…

Z logu to vyzera auto naprv zistilo aky je nabijaci prud a potom si to rozmyslelo, ne je v aute nahodou nastaveny casovy plan kedy sa ma nabijat? — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYIS353LZCHFMM5A7732Z6QR5AVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTEOBWG4ZDGMI> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12867231@ github.com>

1 reply

dzurikmiroslav Apr 17, 2025
Maintainer

v kode co toto riesi som uz dlhsie nic neupravoval (od Nov 22, 2024), ako vyzera board.yaml config ?

ondrom111 · 2025-04-17T19:53:39Z

ondrom111
Apr 17, 2025
Author

# yaml-language-server: $schema= https://github.com/dzurikmiroslav/esp32-evse/raw/refs/heads/master/board-config/board-config-schema-1.json deviceName: ESP32-DevKitC EVSE ledChargingGpio: 19 ledErrorGpio: 18 ledWifiGpio: 17 buttonGpio: 0 pilot: gpio: 27 adcChannel: 0 levels: [2405, 2099, 1792, 1484, 728] proximity: adcChannel: 3 levels: [1650, 820, 430] acRelayGpio: 26 energyMeter: currentAdcChannels: [7] currentScale: 0.759091 voltageAdcChannels: [6] voltageScale: 0.47 serials: - type: uart name: UART via USB rxdGpio: 3 txdGpio: 1 - type: rs485 name: RS485 rxdGpio: 32 txdGpio: 25 rtsGpio: 33 - type: uart name: UART rxdGpio: 2 txdGpio: 15 onewire: gpio: 16 temperatureSensor: true št 17. 4. 2025 o 15:13 Miroslav Dzúrik ***@***.***> napísal(a):

…

v kode co toto riesi som uz dlhsie nic neupravoval (od Nov 22, 2024), ako vyzera board.yaml config ? — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYNJ6W6E7A3QC3VIOUD2Z6SGZAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTEOBWG4ZTQOA> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12867388@ github.com>

1 reply

dzurikmiroslav Apr 18, 2025
Maintainer

Takze konfig je povodny, bez ziadnych uprav? A deje sa toto len pri Tesle? Nezmenilo sa v zapojeni okrem verzie nic ine? Napajanie je cez usb adapter?

ondrom111 · 2025-04-18T19:19:41Z

ondrom111
Apr 18, 2025
Author

Nie napájanie cez 5v zdroj. Akurát predtým som nabíjal cez jednofazový provizórny kábel na priamo a teraz som nabíjal cez 3f menekez zásuvku a originálny kábel. Zajtra ešte skontrolujeme či nie je niekde problém a vyskúšam aj druhé auto. Dňa pi 18. 4. 2025, 20:53 Miroslav Dzúrik ***@***.***> napísal(a):

…

Takze konfig je povodny, bez ziadnych uprav? A deje sa toto len pri Tesle? Nezmenilo sa v zapojeni okrem verzie nic ine? Napajanie je cez usb adapter? — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYMSTIZD3BG42VMPS5L22FC2FAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTEOBYGA4TGMA> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12880930@ github.com>

0 replies

ondrom111 · 2025-04-19T07:39:36Z

ondrom111
Apr 19, 2025
Author

Nikde som nenašiel problém a nenabija ani Renault ani Tesla iba to malé čo malo doteraz problém začalo nabíjať a hneď vyplo , ale tam mám plnú batériu. Dňa pi 18. 4. 2025, 21:19 ANDREJ MITERA ***@***.***> napísal(a):

…

Nie napájanie cez 5v zdroj. Akurát predtým som nabíjal cez jednofazový provizórny kábel na priamo a teraz som nabíjal cez 3f menekez zásuvku a originálny kábel. Zajtra ešte skontrolujeme či nie je niekde problém a vyskúšam aj druhé auto. Dňa pi 18. 4. 2025, 20:53 Miroslav Dzúrik ***@***.***> napísal(a): > Takze konfig je povodny, bez ziadnych uprav? A deje sa toto len pri > Tesle? Nezmenilo sa v zapojeni okrem verzie nic ine? Napajanie je cez usb > adapter? > > — > Reply to this email directly, view it on GitHub > <#81 (reply in thread)>, > or unsubscribe > <https://github.com/notifications/unsubscribe-auth/AN5VPYMSTIZD3BG42VMPS5L22FC2FAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTEOBYGA4TGMA> > . > You are receiving this because you are subscribed to this thread.Message > ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12880930@ > github.com> >

0 replies

ondrom111 · 2025-04-19T09:54:11Z

ondrom111
Apr 19, 2025
Author

Asi bude problém v doske mám dve čo som kúpil osadené a tá provizórna, co vysi iba na kabloch ide aj s novým firmware idem ju skúsiť dať do rozvadzaca miesto tamtej dám vedieť. Dňa so 19. 4. 2025, 9:39 ANDREJ MITERA ***@***.***> napísal(a):

…

Nikde som nenašiel problém a nenabija ani Renault ani Tesla iba to malé čo malo doteraz problém začalo nabíjať a hneď vyplo , ale tam mám plnú batériu. Dňa pi 18. 4. 2025, 21:19 ANDREJ MITERA ***@***.***> napísal(a): > Nie napájanie cez 5v zdroj. Akurát predtým som nabíjal cez jednofazový > provizórny kábel na priamo a teraz som nabíjal cez 3f menekez zásuvku a > originálny kábel. Zajtra ešte skontrolujeme či nie je niekde problém a > vyskúšam aj druhé auto. > > Dňa pi 18. 4. 2025, 20:53 Miroslav Dzúrik ***@***.***> > napísal(a): > >> Takze konfig je povodny, bez ziadnych uprav? A deje sa toto len pri >> Tesle? Nezmenilo sa v zapojeni okrem verzie nic ine? Napajanie je cez usb >> adapter? >> >> — >> Reply to this email directly, view it on GitHub >> <#81 (reply in thread)>, >> or unsubscribe >> <https://github.com/notifications/unsubscribe-auth/AN5VPYMSTIZD3BG42VMPS5L22FC2FAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTEOBYGA4TGMA> >> . >> You are receiving this because you are subscribed to this thread.Message >> ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12880930@ >> github.com> >> >

0 replies

ondrom111 · 2025-04-19T15:44:30Z

ondrom111
Apr 19, 2025
Author

Nič nepomohlo stále nejde. I (3934) wifi:state: init -> auth (0xb0) I (3944) wifi:state: auth -> assoc (0x0) I (3954) wifi:state: assoc -> run (0x10) I (3984) wifi:connected with ANDREJ ADMIN G, aid = 1, channel 5, 40D, bssid = 00:16:78:56:39:de I (3984) wifi:security: WPA2-PSK, phy: bgn, rssi: -57 I (3984) wifi:pm start, type: 1 I (3984) wifi:dp: 1, bi: 102400, li: 3, scale listen interval from 307200 us to 307200 us I (3994) wifi:<ba-add>idx:0 (ifx:0, 00:16:78:56:39:de), tid:6, ssn:2, winSize:64 I (4044) wifi:AP's beacon interval = 102400 us, DTIM period = 1 I (5004) esp_netif_handlers: sta ip: 192.168.1.220, mask: 255.255.255.0, gw: 192.168.1.1 I (5004) wifi: WiFi STA got ip: 192.168.1.220 I (5384) wifi:<ba-add>idx:1 (ifx:0, 00:16:78:56:39:de), tid:0, ssn:2, winSize:64 I (10194) evse: Enter A state I (10194) pilot: Set level 1 I (10194) ac_relay: Set relay: 0 I (10194) energy_meter: Stop session I (10264) evse: Enter E state I (10264) evse: Error bits 1 I (10264) pilot: Set level 0 I (10264) ac_relay: Set relay: 0 I (70304) evse: Enter A state I (70304) pilot: Set level 1 I (70304) ac_relay: Set relay: 0 I (70364) evse: Enter B1 state I (70364) ac_relay: Set relay: 0 I (70364) energy_meter: Start session I (70424) evse: Enter B2 state I (70424) pilot: Set amp 220A*10 duty 374/1023 I (70424) ac_relay: Set relay: 0 I (70484) evse: Enter E state I (70484) evse: Error bits 2 I (70484) pilot: Set level 0 I (70484) ac_relay: Set relay: 0 I (70484) energy_meter: Stop session I (130504) evse: Enter A state I (130504) pilot: Set level 1 I (130504) ac_relay: Set relay: 0 I (130564) evse: Enter B1 state I (130564) ac_relay: Set relay: 0 I (130564) energy_meter: Start session I (130624) evse: Enter B2 state I (130634) pilot: Set amp 220A*10 duty 374/1023 I (130634) ac_relay: Set relay: 0 I (130694) evse: Enter E state I (130694) evse: Error bits 2 I (130694) pilot: Set level 0 I (130694) ac_relay: Set relay: 0 I (130694) energy_meter: Stop session I (190714) evse: Enter A state I (190714) pilot: Set level 1 I (190714) ac_relay: Set relay: 0 I (190774) evse: Enter B1 state I (190774) ac_relay: Set relay: 0 I (190774) energy_meter: Start session I (190834) evse: Enter B2 state I (190834) pilot: Set amp 220A*10 duty 374/1023 I (190844) ac_relay: Set relay: 0 I (190904) evse: Enter E state I (190904) evse: Error bits 2 I (190904) pilot: Set level 0 I (190904) ac_relay: Set relay: 0 I (190904) energy_meter: Stop session I (250964) evse: Enter A state I (250964) pilot: Set level 1 I (250964) ac_relay: Set relay: 0 I (251024) evse: Enter B1 state I (251024) ac_relay: Set relay: 0 I (251024) energy_meter: Start session I (251084) evse: Enter B2 state I (251084) pilot: Set amp 220A*10 duty 374/1023 I (251084) ac_relay: Set relay: 0 I (251144) evse: Enter E state I (251144) evse: Error bits 2 I (251144) pilot: Set level 0 I (251144) ac_relay: Set relay: 0 I (251144) energy_meter: Stop session Dňa so 19. 4. 2025, 11:53 ANDREJ MITERA ***@***.***> napísal(a):

…

Asi bude problém v doske mám dve čo som kúpil osadené a tá provizórna, co vysi iba na kabloch ide aj s novým firmware idem ju skúsiť dať do rozvadzaca miesto tamtej dám vedieť. Dňa so 19. 4. 2025, 9:39 ANDREJ MITERA ***@***.***> napísal(a): > Nikde som nenašiel problém a nenabija ani Renault ani Tesla iba to malé > čo malo doteraz problém začalo nabíjať a hneď vyplo , ale tam mám plnú > batériu. > > Dňa pi 18. 4. 2025, 21:19 ANDREJ MITERA ***@***.***> napísal(a): > >> Nie napájanie cez 5v zdroj. Akurát predtým som nabíjal cez jednofazový >> provizórny kábel na priamo a teraz som nabíjal cez 3f menekez zásuvku a >> originálny kábel. Zajtra ešte skontrolujeme či nie je niekde problém a >> vyskúšam aj druhé auto. >> >> Dňa pi 18. 4. 2025, 20:53 Miroslav Dzúrik ***@***.***> >> napísal(a): >> >>> Takze konfig je povodny, bez ziadnych uprav? A deje sa toto len pri >>> Tesle? Nezmenilo sa v zapojeni okrem verzie nic ine? Napajanie je cez usb >>> adapter? >>> >>> — >>> Reply to this email directly, view it on GitHub >>> <#81 (reply in thread)>, >>> or unsubscribe >>> <https://github.com/notifications/unsubscribe-auth/AN5VPYMSTIZD3BG42VMPS5L22FC2FAVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTEOBYGA4TGMA> >>> . >>> You are receiving this because you are subscribed to this thread.Message >>> ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/12880930@ >>> github.com> >>> >>

11 replies

ondrom111 May 22, 2025
Author

l1

dzurikmiroslav May 22, 2025
Maintainer

Ok, to je dobre, a problem je ze namerany prud skace 0-10A ?

ondrom111 May 22, 2025
Author

je napr 8 a dalsie meranie 18 potom 12 jednoducho velke vykyvy

dzurikmiroslav May 22, 2025
Maintainer

a prudova sonda je aka? nie su okolo jej blizksti ostatne vodice?

ondrom111 May 22, 2025
Author

NO NIE SU DALEKO SKUSIM VYTIAHNU PROVIZORNE VACSIU SLUCKU A OSKUSAM

ondrom111 · 2025-05-23T09:05:50Z

ondrom111
May 23, 2025
Author

Zatiaľ všetko ide, ak budeš mat čas tak iba mrkni na môj lua ci tam neuvidíš chybu alebo možnú úpravu. št 22. 5. 2025 o 9:46 Miroslav Dzúrik ***@***.***> napísal(a):

…

a prudova sonda je aka? nie su okolo jej blizksti ostatne vodice? — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYOEVITVSIR37AF3B5D27V6F3AVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTGMRTGA4DSNQ> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/13230896@ github.com>

3 replies

ondrom111 May 23, 2025
Author

tb (1).zip

dzurikmiroslav May 30, 2025
Maintainer

To mas kod od chatgpt? Je tam kopa volani ktore neexistuju :)
Metoda mqtt.client ma parametre: uri, user, password objekt sa tam neda zadat, resp. ho neprecita...
Mozem ju rozsirit este o client_id ako sme sa bavili...

ondrom111 Jun 1, 2025
Author

ahoj odskusal so 3fazove a ide super, akurat malickost znova refresh webu

ondrom111 · 2025-05-31T08:34:05Z

ondrom111
May 31, 2025
Author

Ano kolega mi to urobil a potom som to upravoval cez gpt. Pomozes mi s tym? A este jedna otazka da sa to po strate spojenia ( ked mqtt HA strati spojenie pri znovapripojeni HA prijima spravy ele esp nie ) musim znova nacitat script a potom to ide, da sa zavolat nacitanie scriptu? vidim ze je nova verzia super ...idem vyskusat. so 31. 5. 2025 o 0:09 Miroslav Dzúrik ***@***.***> napísal(a):

…

To mas kod od chatgpt? Je tam kopa volani ktore neexistuju :) Metoda mqtt.client ma parametre: uri, user, password objekt sa tam neda zadat, resp. ho neprecita... Mozem ju rozsirit este o client_id ako sme sa bavili... — Reply to this email directly, view it on GitHub <#81 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AN5VPYNZHJZVPPWAKS2T7LL3BDJH5AVCNFSM6AAAAABZARO4JGVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTGMZSGU4TSMA> . You are receiving this because you are subscribed to this thread.Message ID: <dzurikmiroslav/esp32-evse/repo-discussions/81/comments/13325990@ github.com>

0 replies

ondrom111 · 2025-11-26T14:25:01Z

ondrom111
Nov 26, 2025
Author

Ahoj potreboval by som poradit. nejde mi od zaciatku prudovy senzor. Premeral som viackrat odpory, vyskusal som viac senzorov aj menil som kalibraciu, ale vsetko bez uspechu. Ostatne vsetko ok. Dal so to na LAN cez prevodnik RS485 → DR134 → Modbus RTU TCP → HA.

4 replies

dzurikmiroslav Nov 26, 2025
Maintainer

Ahoj, myslis tym prudovy transformator nie prudovy chranic? A aku mas cievku?

ondrom111 Nov 26, 2025
Author

skusal som 30a/1v 100a/500mv

dzurikmiroslav Nov 27, 2025
Maintainer

Ja som to navrhoval pre prudovy transformator ktory ma prudovy vystup s pomerom 2000:1, ty mas asi len s napatovy vystupom.
Tym padom je v nom uz intefrovany rezistor a rezisitor R21 (22ohm) na doske nie je potrebny, mal by si to skusit bez neho nakalibrovat.

ondrom111 Nov 29, 2025
Author

Ahoj. Musel som premostit paticu na prudovy senzor vid obrazok. Neviem ci moja patica je ina, ale mala vsetky vyvody a presne sadla do DPS. A teraz funguju vsetky prudove senzory ktore som predtym skusal. Ja len keby mal este niekto taky problem, aby si vedel ze moze byt aj toto. Dakujem a pekny den prajem.

Uh oh!

Help please #81

Uh oh!

ondrom111 Mar 14, 2025

Replies: 28 comments · 49 replies

Uh oh!

dzurikmiroslav Mar 14, 2025 Maintainer

Uh oh!

ondrom111 Mar 14, 2025 Author

Uh oh!

dzurikmiroslav Mar 14, 2025 Maintainer

Uh oh!

ondrom111 Mar 14, 2025 Author

Uh oh!

dzurikmiroslav Mar 14, 2025 Maintainer

Uh oh!

Uh oh!

ondrom111 Mar 14, 2025 Author

Uh oh!

dzurikmiroslav Mar 14, 2025 Maintainer

Uh oh!

ondrom111 Mar 15, 2025 Author

Uh oh!

ondrom111 Mar 15, 2025 Author

Uh oh!

dzurikmiroslav Mar 19, 2025 Maintainer

Uh oh!

ondrom111 Mar 19, 2025 Author

Uh oh!

dzurikmiroslav Mar 19, 2025 Maintainer

Uh oh!

ondrom111 Mar 19, 2025 Author

Uh oh!

ondrom111 Mar 19, 2025 Author

Uh oh!

dzurikmiroslav Mar 19, 2025 Maintainer

Uh oh!

ondrom111 Mar 19, 2025 Author

Uh oh!

dzurikmiroslav Mar 19, 2025 Maintainer

Uh oh!

ondrom111 Mar 19, 2025 Author

Uh oh!

dzurikmiroslav Mar 19, 2025 Maintainer

Uh oh!

ondrom111 Mar 19, 2025 Author

Uh oh!

dzurikmiroslav Mar 19, 2025 Maintainer

Uh oh!

ondrom111 Mar 19, 2025 Author

Uh oh!

dzurikmiroslav Mar 19, 2025 Maintainer

Uh oh!

ondrom111 Mar 19, 2025 Author

Uh oh!

ondrom111 Mar 19, 2025 Author

Uh oh!

dzurikmiroslav Mar 20, 2025 Maintainer

Uh oh!

ondrom111 Mar 20, 2025 Author

Uh oh!

dzurikmiroslav Mar 20, 2025 Maintainer

Uh oh!

ondrom111 Apr 11, 2025 Author

Uh oh!

dzurikmiroslav Apr 11, 2025 Maintainer

Uh oh!

dzurikmiroslav Apr 11, 2025 Maintainer

Uh oh!

ondrom111 Apr 11, 2025 Author

Uh oh!

ondrom111 Apr 12, 2025 Author

Uh oh!

ondrom111
Mar 14, 2025

Replies: 28 comments 49 replies

dzurikmiroslav
Mar 14, 2025
Maintainer

ondrom111 Mar 14, 2025
Author

dzurikmiroslav Mar 14, 2025
Maintainer

ondrom111
Mar 14, 2025
Author

dzurikmiroslav Mar 14, 2025
Maintainer

ondrom111
Mar 14, 2025
Author

dzurikmiroslav Mar 14, 2025
Maintainer

ondrom111 Mar 15, 2025
Author

ondrom111 Mar 15, 2025
Author

dzurikmiroslav Mar 19, 2025
Maintainer

ondrom111
Mar 19, 2025
Author

dzurikmiroslav Mar 19, 2025
Maintainer

ondrom111
Mar 19, 2025
Author

ondrom111
Mar 19, 2025
Author

dzurikmiroslav Mar 19, 2025
Maintainer

ondrom111
Mar 19, 2025
Author

dzurikmiroslav Mar 19, 2025
Maintainer

ondrom111
Mar 19, 2025
Author

dzurikmiroslav Mar 19, 2025
Maintainer

ondrom111
Mar 19, 2025
Author

dzurikmiroslav Mar 19, 2025
Maintainer

ondrom111
Mar 19, 2025
Author

dzurikmiroslav Mar 19, 2025
Maintainer

ondrom111
Mar 19, 2025
Author

ondrom111
Mar 19, 2025
Author

dzurikmiroslav Mar 20, 2025
Maintainer

ondrom111 Mar 20, 2025
Author

dzurikmiroslav Mar 20, 2025
Maintainer

ondrom111
Apr 11, 2025
Author

dzurikmiroslav Apr 11, 2025
Maintainer

dzurikmiroslav Apr 11, 2025
Maintainer

ondrom111 Apr 11, 2025
Author

ondrom111 Apr 12, 2025
Author