chore: improves Klipper typings

Signed-off-by: Pedro Lamas <[email protected]>

Author: pedrolamas

src/monaco/language/klipper-config.tmLanguage.json

@@ -65,7 +65,7 @@
 		},
 		"known_config_block_name": {
 			"name": "storage.type",
-			"match": "(?i)\\b(ad5206|adc_scaled|adc_temperature|adxl345|angle|bed_mesh|bed_screws|bed_tilt|bltouch|board_pins|controller_fan|delayed_gcode|delta_calibrate|display|display_data|display_glyph|display_status|display_template|dotstar|dual_carriage|duplicate_pin_override|endstop_phase|extruder_stepper|extruder[1-9]{0,1}|fan|fan_generic|filament_motion_sensor|filament_switch_sensor|firmware_retraction|force_move|gcode_arcs|gcode_button|gcode_macro|hall_filament_width_sensor|heater_bed|heater_fan|heater_generic|homing_heaters|homing_override|idle_timeout|include|input_shaper|led|manual_probe|manual_stepper|mcp4018|mcp4451|mcp4728|mcu|menu|multi_pin|neopixel|output_pin|palette2|pause_resume|pca9533|pca9632|printer|probe|quad_gantry_level|replicape|resonance_tester|respond|safe_z_home|samd_sercom|save_variables|screws_tilt_adjust|sdcard_loop|servo|skew_correction|smart_effector|static_digital_output|stepper_(bed|arm|[abcdxy]|z[1-9]{0,1})|sx1509|temperature_fan|temperature_sensor|thermistor|tsl1401cl_filament_width_sensor|verify_heater|virtual_sdcard|z_tilt)\\b"
+			"match": "(?i)\\b(ad5206|adc_scaled|adc_temperature|adxl345|angle|bed_mesh|bed_screws|bed_tilt|bltouch|board_pins|controller_fan|delayed_gcode|delta_calibrate|display|display_data|display_glyph|display_status|display_template|dotstar|dual_carriage|duplicate_pin_override|endstop_phase|extruder_stepper|extruder[1-9]{0,1}|fan|fan_generic|filament_motion_sensor|filament_switch_sensor|firmware_retraction|force_move|gcode_arcs|gcode_button|gcode_macro|hall_filament_width_sensor|heater_bed|heater_fan|heater_generic|homing_heaters|homing_override|idle_timeout|include|input_shaper|led|manual_probe|manual_stepper|mcp4018|mcp4451|mcp4728|mcu|menu|multi_pin|neopixel|output_pin|palette2|pause_resume|pca9533|pca9632|printer|probe|quad_gantry_level|replicape|resonance_tester|respond|safe_z_home|samd_sercom|save_variables|screws_tilt_adjust|sdcard_loop|servo|skew_correction|smart_effector|static_digital_output|static_pwm_clock|stepper_(bed|arm|[abcdxy]|z[1-9]{0,1})|sx1509|temperature_fan|temperature_sensor|thermistor|tsl1401cl_filament_width_sensor|verify_heater|virtual_sdcard|z_tilt)\\b"
 		},
 		"known_driver_type": {
 			"name": "support.type",

src/typings/klipper.d.ts

@@ -939,6 +939,8 @@ declare namespace Klipper {
 
       [key: `load_cell ${Lowercase<string>}`]: LoadCellSettings;
 
+      [key: `static_pwm_clock ${Lowercase<string>}`]: StaticPwmClockSettings;
+
       // These keys are for kalico modules
 
       danger_options: KalicoPrinterDangerOptionsSettings;
@@ -1470,6 +1472,10 @@ declare namespace Klipper {
     vref?: string;
   }
 
+  export interface StaticPwmClockSettings {
+    frequency: number;
+  }
+
   export interface KalicoPrinterDangerOptionsSettings {
     minimal_logging: boolean;
     log_statistics: boolean;