HP ssacli - rebuilding shouldn't perhaps still be warning state?

[calestyo]

Hey.

This is the very same system as described in #211... i.e. the same failed drive, output, etc..

After marking the predictively failed disk (which is actually completely broken and the controller doesn't just get it... o.O), and rebooting the system, HP Smart Array started with an auto rebuild.

check_raid outputs here the following:

# /usr/lib/nagios/plugins/check_raid
Unhandled: [Warning: Unrecoverable Media Errors Detected on Drives during previous Rebuild ]
Unhandled: [or Background Surface Analysis (ARM) scan. Errors will be fixed automatically]
Unhandled: [when the sector(s) are overwritten. Backup and Restore are recommended.]
Unhandled: [Warning: Unrecoverable Media Errors Detected on Drives during previous Rebuild ]
Unhandled: [or Background Surface Analysis (ARM) scan. Errors will be fixed automatically]
Unhandled: [when the sector(s) are overwritten. Backup and Restore are recommended.]
OK: ssacli:[HPE Smart Array P816i-a SR Gen10[OK]: Array A(OK)[LUN1:OK], Array B(OK)[LUN2:Recovering, 54.28% complete,LUN3:Ready for Rebuild,LUN4:Ready for Rebuild,LUN5:Ready for Rebuild,LUN6:Ready for Rebuild,LUN7:Ready for Rebuild,LUN8:Ready for Rebuild,LUN9:Ready for Rebuild,LUN10:Ready for Rebuild,LUN11:Ready for Rebuild,LUN12:Ready for Rebuild,LUN13:Ready for Rebuild]]

I.e. it gives OK while it's actually still rebuilding.
I think it would be better, if in that state it would still give a WARNING, because it's not yet clear whether the rebuild succeeds - e.g. with this bogus drive, it definitely won't (the drive is suuuuuuper slow... I'd be dead before any rebuild had finished).

Following, some ssacli output while rebuilding, just if that helps:

[calestyo]

# ssacli controller all show detail

HPE Smart Array P816i-a SR Gen10 in Slot 0 (Embedded)


Warning: Unrecoverable Media Errors Detected on Drives during previous Rebuild 
or Background Surface Analysis (ARM) scan. Errors will be fixed automatically
when the sector(s) are overwritten. Backup and Restore are recommended. The
following logical drives are affected: 4, 5

   Bus Interface: PCI
   Slot: 0
   Serial Number: PWXLH0CRHF002C
   RAID 6 Status: Enabled
   Controller Status: OK
   Hardware Revision: A
   Firmware Version: 4.11
   Firmware Supports Online Firmware Activation: True
   Driver Supports Online Firmware Activation: True
   Rebuild Priority: High
   Expand Priority: Medium
   Surface Scan Delay: 3 secs
   Surface Scan Mode: Idle
   Parallel Surface Scan Supported: Yes
   Current Parallel Surface Scan Count: 1
   Max Parallel Surface Scan Count: 16
   Queue Depth: Automatic
   Monitor and Performance Delay: 60  min
   Elevator Sort: Enabled
   Degraded Performance Optimization: Disabled
   Inconsistency Repair Policy: Disabled
   Write Cache Bypass Threshold Size: 1040 KiB
   Wait for Cache Room: Disabled
   Surface Analysis Inconsistency Notification: Disabled
   Post Prompt Timeout: 0 secs
   Cache Board Present: True
   Cache Status: OK
   Cache Ratio: 10% Read / 90% Write
   Configured Drive Write Cache Policy: Disable
   Unconfigured Drive Write Cache Policy: Default
   Total Cache Size: 4.0
   Total Cache Memory Available: 3.8
   Battery Backed Cache Size: 3.8
   No-Battery Write Cache: Disabled
   SSD Caching RAID5 WriteBack Enabled: True
   SSD Caching Version: 2
   Cache Backup Power Source: Batteries
   Battery/Capacitor Count: 1
   Battery/Capacitor Status: OK
   SATA NCQ Supported: True
   Spare Activation Mode: Activate on physical drive failure (default)
   Controller Temperature (C): 58
   Capacitor Temperature  (C): 45
   Number of Ports: 4 Internal only
   Encryption: Not Set
   Express Local Encryption: False
   Driver Name: smartpqi
   Driver Version: Linux 1.2.16-010
   PCI Address (Domain:Bus:Device.Function): 0000:62:00.0
   Negotiated PCIe Data Rate: PCIe 3.0 x8 (7880 MB/s)
   Controller Mode: Mixed
   Port Max Phy Rate Limiting Supported: False
   Latency Scheduler Setting: Disabled
   Current Power Mode: MaxPerformance
   Survival Mode: Enabled
   Host Serial Number: CZJ11703R4
   Sanitize Erase Supported: True
   Sanitize Lock: None
   Sensor ID: 0
      Location: Capacitor
      Current Value (C): 45
      Max Value Since Power On: 45
   Sensor ID: 1
      Location: ASIC
      Current Value (C): 58
      Max Value Since Power On: 58
   Sensor ID: 2
      Location: Unknown
      Current Value (C): 42
      Max Value Since Power On: 42
   Primary Boot Volume: None
   Secondary Boot Volume: None

[calestyo]

# ssacli controller all show config

HPE Smart Array P816i-a SR Gen10 in Slot 0 (Embedded)  (sn: PWXLH0CRHF002C)



   Apollo 4200 LFF  at Port 1I, Box 1, OK



   Apollo 4200 LFF  at Port 3I, Box 1, OK


   Port Name: 1I (Mixed)

   Port Name: 2I (Mixed)

   Port Name: 3I (Mixed)

   Port Name: 4I (Mixed)

   Array A (Solid State SATA, Unused Space: 0  MB)

      logicaldrive 1 (447.10 GB, RAID 1, OK)

      physicaldrive 3I:1:15 (port 3I:box 1:bay 15, SATA SSD, 480 GB, OK)
      physicaldrive 3I:1:16 (port 3I:box 1:bay 16, SATA SSD, 480 GB, OK)


   Array B (SAS, Unused Space: 0  MB)

      logicaldrive 2 (16.00 TB, RAID 6, Recovering, 55.54% complete)
      logicaldrive 3 (16.00 TB, RAID 6, Ready for Rebuild)


Warning: Unrecoverable Media Errors Detected on Drives during previous Rebuild 
or Background Surface Analysis (ARM) scan. Errors will be fixed automatically
when the sector(s) are overwritten. Backup and Restore are recommended.

      logicaldrive 4 (16.00 TB, RAID 6, Ready for Rebuild)


Warning: Unrecoverable Media Errors Detected on Drives during previous Rebuild 
or Background Surface Analysis (ARM) scan. Errors will be fixed automatically
when the sector(s) are overwritten. Backup and Restore are recommended.

      logicaldrive 5 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 6 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 7 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 8 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 9 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 10 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 11 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 12 (14.60 TB, RAID 6, Ready for Rebuild)
      logicaldrive 13 (32.00 GB, RAID 6, Ready for Rebuild)

      physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:5 (port 1I:box 1:bay 5, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:6 (port 1I:box 1:bay 6, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:7 (port 1I:box 1:bay 7, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:8 (port 1I:box 1:bay 8, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:9 (port 1I:box 1:bay 9, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:10 (port 1I:box 1:bay 10, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:11 (port 1I:box 1:bay 11, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:12 (port 1I:box 1:bay 12, SAS HDD, 16 TB, OK)
      physicaldrive 3I:1:13 (port 3I:box 1:bay 13, SAS HDD, 16 TB, Rebuilding)
      physicaldrive 3I:1:14 (port 3I:box 1:bay 14, SAS HDD, 16 TB, OK)

   Enclosure SEP (Vendor ID HPE, Model Apollo 4200 LFF) 375  (WWID: 5001438043D6A63C, Port: 3I, Box: 1)

   Enclosure SEP (Vendor ID HPE, Model Apollo 4200 LFF) 376  (WWID: 5001438043D60E3C, Port: 1I, Box: 1)

   Expander 377  (WWID: 5001438043D6A63D, Port: 3I, Box: 1)

   Expander 378  (WWID: 5001438043D60E3D, Port: 1I, Box: 1)

   SEP (Vendor ID HPE, Model Smart Adapter) 379  (WWID: 51402EC0167D2450)

[calestyo]

# ssacli controller slot=0 physicaldrive all show

HPE Smart Array P816i-a SR Gen10 in Slot 0 (Embedded)

   Array A

      physicaldrive 3I:1:15 (port 3I:box 1:bay 15, SATA SSD, 480 GB, OK)
      physicaldrive 3I:1:16 (port 3I:box 1:bay 16, SATA SSD, 480 GB, OK)

   Array B

      physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:5 (port 1I:box 1:bay 5, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:6 (port 1I:box 1:bay 6, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:7 (port 1I:box 1:bay 7, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:8 (port 1I:box 1:bay 8, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:9 (port 1I:box 1:bay 9, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:10 (port 1I:box 1:bay 10, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:11 (port 1I:box 1:bay 11, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:12 (port 1I:box 1:bay 12, SAS HDD, 16 TB, OK)
      physicaldrive 3I:1:13 (port 3I:box 1:bay 13, SAS HDD, 16 TB, Rebuilding)
      physicaldrive 3I:1:14 (port 3I:box 1:bay 14, SAS HDD, 16 TB, OK)

[calestyo]

# ssacli controller slot=0 logicaldrive all show

HPE Smart Array P816i-a SR Gen10 in Slot 0 (Embedded)

   Array A

      logicaldrive 1 (447.10 GB, RAID 1, OK)

   Array B

      logicaldrive 2 (16.00 TB, RAID 6, Recovering, 55.73% complete)
      logicaldrive 3 (16.00 TB, RAID 6, Ready for Rebuild)


Warning: Unrecoverable Media Errors Detected on Drives during previous Rebuild 
or Background Surface Analysis (ARM) scan. Errors will be fixed automatically
when the sector(s) are overwritten. Backup and Restore are recommended.

      logicaldrive 4 (16.00 TB, RAID 6, Ready for Rebuild)


Warning: Unrecoverable Media Errors Detected on Drives during previous Rebuild 
or Background Surface Analysis (ARM) scan. Errors will be fixed automatically
when the sector(s) are overwritten. Backup and Restore are recommended.

      logicaldrive 5 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 6 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 7 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 8 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 9 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 10 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 11 (16.00 TB, RAID 6, Ready for Rebuild)
      logicaldrive 12 (14.60 TB, RAID 6, Ready for Rebuild)
      logicaldrive 13 (32.00 GB, RAID 6, Ready for Rebuild)

[calestyo]

# ssacli ctrl all show config detail

HPE Smart Array P816i-a SR Gen10 in Slot 0 (Embedded)


Warning: Unrecoverable Media Errors Detected on Drives during previous Rebuild 
or Background Surface Analysis (ARM) scan. Errors will be fixed automatically
when the sector(s) are overwritten. Backup and Restore are recommended. The
following logical drives are affected: 4, 5

   Bus Interface: PCI
   Slot: 0
   Serial Number: PWXLH0CRHF002C
   RAID 6 Status: Enabled
   Controller Status: OK
   Hardware Revision: A
   Firmware Version: 4.11
   Firmware Supports Online Firmware Activation: True
   Driver Supports Online Firmware Activation: True
   Rebuild Priority: High
   Expand Priority: Medium
   Surface Scan Delay: 3 secs
   Surface Scan Mode: Idle
   Parallel Surface Scan Supported: Yes
   Current Parallel Surface Scan Count: 1
   Max Parallel Surface Scan Count: 16
   Queue Depth: Automatic
   Monitor and Performance Delay: 60  min
   Elevator Sort: Enabled
   Degraded Performance Optimization: Disabled
   Inconsistency Repair Policy: Disabled
   Write Cache Bypass Threshold Size: 1040 KiB
   Wait for Cache Room: Disabled
   Surface Analysis Inconsistency Notification: Disabled
   Post Prompt Timeout: 0 secs
   Cache Board Present: True
   Cache Status: OK
   Cache Ratio: 10% Read / 90% Write
   Configured Drive Write Cache Policy: Disable
   Unconfigured Drive Write Cache Policy: Default
   Total Cache Size: 4.0
   Total Cache Memory Available: 3.8
   Battery Backed Cache Size: 3.8
   No-Battery Write Cache: Disabled
   SSD Caching RAID5 WriteBack Enabled: True
   SSD Caching Version: 2
   Cache Backup Power Source: Batteries
   Battery/Capacitor Count: 1
   Battery/Capacitor Status: OK
   SATA NCQ Supported: True
   Spare Activation Mode: Activate on physical drive failure (default)
   Controller Temperature (C): 58
   Capacitor Temperature  (C): 45
   Number of Ports: 4 Internal only
   Encryption: Not Set
   Express Local Encryption: False
   Driver Name: smartpqi
   Driver Version: Linux 1.2.16-010
   PCI Address (Domain:Bus:Device.Function): 0000:62:00.0
   Negotiated PCIe Data Rate: PCIe 3.0 x8 (7880 MB/s)
   Controller Mode: Mixed
   Port Max Phy Rate Limiting Supported: False
   Latency Scheduler Setting: Disabled
   Current Power Mode: MaxPerformance
   Survival Mode: Enabled
   Host Serial Number: CZJ11703R4
   Sanitize Erase Supported: True
   Sanitize Lock: None
   Sensor ID: 0
      Location: Capacitor
      Current Value (C): 45
      Max Value Since Power On: 45
   Sensor ID: 1
      Location: ASIC
      Current Value (C): 58
      Max Value Since Power On: 58
   Sensor ID: 2
      Location: Unknown
      Current Value (C): 42
      Max Value Since Power On: 42
   Primary Boot Volume: None
   Secondary Boot Volume: None



   Apollo 4200 LFF  at Port 1I, Box 1, OK

      Power Supply Status: Not Redundant
      Vendor ID: HPE
      Serial Number: PESZP0BRHEU0JS
      Firmware Version: 1.79
      Drive Bays: 12
      Port: 1I
      Box: 1
      Location: Internal
      Active Path: 1I:1, OK
      Active Path: 2I:1, OK

   Expander 378 
      Device Number: 378
      Firmware Version: 1.79
      WWID: 5001438043D60E3D
      Port: 1I
      Box: 1
      Vendor ID: HPE

   Enclosure SEP (Vendor ID HPE, Model Apollo 4200 LFF) 376 
      Device Number: 376
      Firmware Version: 1.79
      WWID: 5001438043D60E3C
      Port: 1I
      Box: 1
      Vendor ID: HPE
      Model: Apollo 4200 LFF

   Physical Drives
      physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:5 (port 1I:box 1:bay 5, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:6 (port 1I:box 1:bay 6, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:7 (port 1I:box 1:bay 7, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:8 (port 1I:box 1:bay 8, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:9 (port 1I:box 1:bay 9, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:10 (port 1I:box 1:bay 10, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:11 (port 1I:box 1:bay 11, SAS HDD, 16 TB, OK)
      physicaldrive 1I:1:12 (port 1I:box 1:bay 12, SAS HDD, 16 TB, OK)



   Apollo 4200 LFF  at Port 3I, Box 1, OK

      Power Supply Status: Not Redundant
      Vendor ID: HPE
      Serial Number: PESZP0BRHEU0KU
      Firmware Version: 1.79
      Drive Bays: 12
      Port: 3I
      Box: 1
      Location: Internal
      Active Path: 3I:1, OK
      Active Path: 4I:1, OK

   Expander 377 
      Device Number: 377
      Firmware Version: 1.79
      WWID: 5001438043D6A63D
      Port: 3I
      Box: 1
      Vendor ID: HPE

   Enclosure SEP (Vendor ID HPE, Model Apollo 4200 LFF) 375 
      Device Number: 375
      Firmware Version: 1.79
      WWID: 5001438043D6A63C
      Port: 3I
      Box: 1
      Vendor ID: HPE
      Model: Apollo 4200 LFF

   Physical Drives
      physicaldrive 3I:1:13 (port 3I:box 1:bay 13, SAS HDD, 16 TB, Rebuilding)
      physicaldrive 3I:1:14 (port 3I:box 1:bay 14, SAS HDD, 16 TB, OK)
      physicaldrive 3I:1:15 (port 3I:box 1:bay 15, SATA SSD, 480 GB, OK)
      physicaldrive 3I:1:16 (port 3I:box 1:bay 16, SATA SSD, 480 GB, OK)


   Port Name: 1I
         Port ID: 0
         Port Mode: Mixed
         Port Connection Number: 0
         SAS Address: 51402EC0167D2440
         Port Location: Internal

   Port Name: 2I
         Port ID: 1
         Port Mode: Mixed
         Port Connection Number: 1
         SAS Address: 51402EC0167D2444
         Port Location: Internal

   Port Name: 3I
         Port ID: 2
         Port Mode: Mixed
         Port Connection Number: 2
         SAS Address: 51402EC0167D2448
         Port Location: Internal

   Port Name: 4I
         Port ID: 3
         Port Mode: Mixed
         Port Connection Number: 3
         SAS Address: 51402EC0167D244C
         Port Location: Internal

   Array: A
      Interface Type: Solid State SATA
      Unused Space: 0 MB (0.00%)
      Used Space: 894.20 GB (100.00%)
      Status: OK
      MultiDomain Status: OK
      Array Type: Data 
      Smart Path: enable


      Logical Drive: 1
         Size: 447.10 GB
         Fault Tolerance: 1
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 65535
         Strip Size: 256 KB
         Full Stripe Size: 256 KB
         Status: OK
         Unrecoverable Media Errors: None
         MultiDomain Status: OK
         Caching:  Disabled
         Unique Identifier: 600508B1001C95525F17C2427C5D7FA2
         Disk Name: /dev/sda 
         Mount Points: 446.1 GiB Partition   2, 1023 MiB Partition   1 /, /boot/efi
         Disk Partition Information
            Partition   2: Basic, 446.1 GiB, /
            Partition   1: Basic, 1023 MiB, /boot/efi
         Logical Drive Label: system
         Mirror Group 1:
            physicaldrive 3I:1:15 (port 3I:box 1:bay 15, SATA SSD, 480 GB, OK)
         Mirror Group 2:
            physicaldrive 3I:1:16 (port 3I:box 1:bay 16, SATA SSD, 480 GB, OK)
         Drive Type: Data
         LD Acceleration Method: Smart Path


      physicaldrive 3I:1:15
         Port: 3I
         Box: 1
         Bay: 15
         Status: OK
         Drive Type: Data Drive
         Interface Type: Solid State SATA
         Size: 480 GB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Firmware Revision: HPG1
         Serial Number: 20372D53A88C
         WWID: 5001438043D6A602
         Model: ATA     VK000480GXAWK
         SATA NCQ Capable: True
         SATA NCQ Enabled: True
         Current Temperature (C): 35
         Maximum Temperature (C): 43
         Usage remaining: 99.92%
         Power On Hours: 6261
         Estimated Life Remaining based on workload to date: 325832 days
         SSD Smart Trip Wearout: False
         PHY Count: 1
         PHY Transfer Rate: 6.0Gbps
         PHY Physical Link Rate: 6.0Gbps
         PHY Maximum Link Rate: 6.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Freeze Lock Supported: True
         Sanitize Anti-Freeze Lock Supported: True
         Sanitize Lock: None
         Sanitize Estimated Max Erase Time: 1 minute(s), 5 second(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: B71CCA70B48385F7
         Self Encrypting Drive: False

      physicaldrive 3I:1:16
         Port: 3I
         Box: 1
         Bay: 16
         Status: OK
         Drive Type: Data Drive
         Interface Type: Solid State SATA
         Size: 480 GB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Firmware Revision: HPG1
         Serial Number: 20372D53A8BB
         WWID: 5001438043D6A603
         Model: ATA     VK000480GXAWK
         SATA NCQ Capable: True
         SATA NCQ Enabled: True
         Current Temperature (C): 33
         Maximum Temperature (C): 40
         Usage remaining: 99.92%
         Power On Hours: 6261
         Estimated Life Remaining based on workload to date: 325832 days
         SSD Smart Trip Wearout: False
         PHY Count: 1
         PHY Transfer Rate: 6.0Gbps
         PHY Physical Link Rate: 6.0Gbps
         PHY Maximum Link Rate: 6.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Freeze Lock Supported: True
         Sanitize Anti-Freeze Lock Supported: True
         Sanitize Lock: None
         Sanitize Estimated Max Erase Time: 1 minute(s), 5 second(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: C6ED8C99FF9202FF
         Self Encrypting Drive: False



   Array: B
      Interface Type: SAS
      Unused Space: 0 MB (0.00%)
      Used Space: 203.74 TB (100.00%)
      Status: OK
      MultiDomain Status: OK
      Array Type: Data 
      Smart Path: disable


      Logical Drive: 2
         Size: 16.00 TB
         Fault Tolerance: 6
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 65535
         Strip Size: 512 KB
         Full Stripe Size: 6144 KB
         Status: Recovering, 55.82% complete
         Unrecoverable Media Errors: None
         MultiDomain Status: OK
         Caching:  Enabled
         Parity Initialization Status: Initialization Completed
         Unique Identifier: 600508B1001C8552A4A98DAA38D9D6BD
         Disk Name: /dev/sdb 
         Mount Points: 16.0 TiB Partition   0 /srv/dcache/pools/meta/a/0/data
         Disk Partition Information
            Partition   0: Basic, 16.0 TiB, /srv/dcache/pools/meta/a/0/data
         Logical Drive Label: data-a-0
         Drive Type: Data
         LD Acceleration Method: Controller Cache

      Logical Drive: 3
         Size: 16.00 TB
         Fault Tolerance: 6
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 65535
         Strip Size: 512 KB
         Full Stripe Size: 6144 KB
         Status: Ready for Rebuild
         Unrecoverable Media Errors: None
         MultiDomain Status: OK
         Caching:  Enabled
         Parity Initialization Status: Initialization Completed
         Unique Identifier: 600508B1001C05B6E4302BB23614AB34
         Disk Name: /dev/sdc 
         Mount Points: 16.0 TiB Partition   0 /srv/dcache/pools/meta/a/1/data
         Disk Partition Information
            Partition   0: Basic, 16.0 TiB, /srv/dcache/pools/meta/a/1/data
         Logical Drive Label: data-a-1
         Drive Type: Data
         LD Acceleration Method: Controller Cache



Warning: Unrecoverable Media Errors Detected on Drives during previous Rebuild 
or Background Surface Analysis (ARM) scan. Errors will be fixed automatically
when the sector(s) are overwritten. Backup and Restore are recommended.

      Logical Drive: 4
         Size: 16.00 TB
         Fault Tolerance: 6
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 65535
         Strip Size: 512 KB
         Full Stripe Size: 6144 KB
         Status: Ready for Rebuild
         Unrecoverable Media Errors: Detected
         MultiDomain Status: OK
         Caching:  Enabled
         Parity Initialization Status: Initialization Completed
         Unique Identifier: 600508B1001C9742A823112B060CC885
         Disk Name: /dev/sdh 
         Mount Points: 16.0 TiB Partition   0 /srv/dcache/pools/meta/a/2/data
         Disk Partition Information
            Partition   0: Basic, 16.0 TiB, /srv/dcache/pools/meta/a/2/data
         Logical Drive Label: data-a-2
         Drive Type: Data
         LD Acceleration Method: Controller Cache



Warning: Unrecoverable Media Errors Detected on Drives during previous Rebuild 
or Background Surface Analysis (ARM) scan. Errors will be fixed automatically
when the sector(s) are overwritten. Backup and Restore are recommended.

      Logical Drive: 5
         Size: 16.00 TB
         Fault Tolerance: 6
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 65535
         Strip Size: 512 KB
         Full Stripe Size: 6144 KB
         Status: Ready for Rebuild
         Unrecoverable Media Errors: Detected
         MultiDomain Status: OK
         Caching:  Enabled
         Parity Initialization Status: Initialization Completed
         Unique Identifier: 600508B1001CE021DF21F5EF83705F4F
         Disk Name: /dev/sdi 
         Mount Points: 16.0 TiB Partition   0 /srv/dcache/pools/meta/a/3/data
         Disk Partition Information
            Partition   0: Basic, 16.0 TiB, /srv/dcache/pools/meta/a/3/data
         Logical Drive Label: data-a-3
         Drive Type: Data
         LD Acceleration Method: Controller Cache

      Logical Drive: 6
         Size: 16.00 TB
         Fault Tolerance: 6
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 65535
         Strip Size: 512 KB
         Full Stripe Size: 6144 KB
         Status: Ready for Rebuild
         Unrecoverable Media Errors: None
         MultiDomain Status: OK
         Caching:  Enabled
         Parity Initialization Status: Initialization Completed
         Unique Identifier: 600508B1001C7B71642E863F2DD2FCAB
         Disk Name: /dev/sde 
         Mount Points: 16.0 TiB Partition   0 /srv/dcache/pools/meta/a/4/data
         Disk Partition Information
            Partition   0: Basic, 16.0 TiB, /srv/dcache/pools/meta/a/4/data
         Logical Drive Label: data-a-4
         Drive Type: Data
         LD Acceleration Method: Controller Cache

      Logical Drive: 7
         Size: 16.00 TB
         Fault Tolerance: 6
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 65535
         Strip Size: 512 KB
         Full Stripe Size: 6144 KB
         Status: Ready for Rebuild
         Unrecoverable Media Errors: None
         MultiDomain Status: OK
         Caching:  Enabled
         Parity Initialization Status: Initialization Completed
         Unique Identifier: 600508B1001CF77CC9DABA4EC15DC0B2
         Disk Name: /dev/sdd 
         Mount Points: 16.0 TiB Partition   0 /srv/dcache/pools/meta/a/5/data
         Disk Partition Information
            Partition   0: Basic, 16.0 TiB, /srv/dcache/pools/meta/a/5/data
         Logical Drive Label: data-a-5
         Drive Type: Data
         LD Acceleration Method: Controller Cache

      Logical Drive: 8
         Size: 16.00 TB
         Fault Tolerance: 6
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 65535
         Strip Size: 512 KB
         Full Stripe Size: 6144 KB
         Status: Ready for Rebuild
         Unrecoverable Media Errors: None
         MultiDomain Status: OK
         Caching:  Enabled
         Parity Initialization Status: Initialization Completed
         Unique Identifier: 600508B1001C7786AC2BF1514208A99E
         Disk Name: /dev/sdj 
         Mount Points: 16.0 TiB Partition   0 /srv/dcache/pools/meta/a/6/data
         Disk Partition Information
            Partition   0: Basic, 16.0 TiB, /srv/dcache/pools/meta/a/6/data
         Logical Drive Label: data-a-6
         Drive Type: Data
         LD Acceleration Method: Controller Cache

      Logical Drive: 9
         Size: 16.00 TB
         Fault Tolerance: 6
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 65535
         Strip Size: 512 KB
         Full Stripe Size: 6144 KB
         Status: Ready for Rebuild
         Unrecoverable Media Errors: None
         MultiDomain Status: OK
         Caching:  Enabled
         Parity Initialization Status: Initialization Completed
         Unique Identifier: 600508B1001CEB0DA77F0A109E0DDD2A
         Disk Name: /dev/sdf 
         Mount Points: 16.0 TiB Partition   0 /srv/dcache/pools/meta/a/7/data
         Disk Partition Information
            Partition   0: Basic, 16.0 TiB, /srv/dcache/pools/meta/a/7/data
         Logical Drive Label: data-a-7
         Drive Type: Data
         LD Acceleration Method: Controller Cache

      Logical Drive: 10
         Size: 16.00 TB
         Fault Tolerance: 6
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 65535
         Strip Size: 512 KB
         Full Stripe Size: 6144 KB
         Status: Ready for Rebuild
         Unrecoverable Media Errors: None
         MultiDomain Status: OK
         Caching:  Enabled
         Parity Initialization Status: Initialization Completed
         Unique Identifier: 600508B1001C22E53F9085EEA5355739
         Disk Name: /dev/sdg 
         Mount Points: 16.0 TiB Partition   0 /srv/dcache/pools/meta/a/8/data
         Disk Partition Information
            Partition   0: Basic, 16.0 TiB, /srv/dcache/pools/meta/a/8/data
         Logical Drive Label: data-a-8
         Drive Type: Data
         LD Acceleration Method: Controller Cache

      Logical Drive: 11
         Size: 16.00 TB
         Fault Tolerance: 6
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 65535
         Strip Size: 512 KB
         Full Stripe Size: 6144 KB
         Status: Ready for Rebuild
         Unrecoverable Media Errors: None
         MultiDomain Status: OK
         Caching:  Enabled
         Parity Initialization Status: Initialization Completed
         Unique Identifier: 600508B1001C294C19B603A162D37DD9
         Disk Name: /dev/sdk 
         Mount Points: 16.0 TiB Partition   0 /srv/dcache/pools/meta/a/9/data
         Disk Partition Information
            Partition   0: Basic, 16.0 TiB, /srv/dcache/pools/meta/a/9/data
         Logical Drive Label: data-a-9
         Drive Type: Data
         LD Acceleration Method: Controller Cache

      Logical Drive: 12
         Size: 14.60 TB
         Fault Tolerance: 6
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 65535
         Strip Size: 512 KB
         Full Stripe Size: 6144 KB
         Status: Ready for Rebuild
         Unrecoverable Media Errors: None
         MultiDomain Status: OK
         Caching:  Enabled
         Parity Initialization Status: Initialization Completed
         Unique Identifier: 600508B1001CEEA59191C7B0E9912BB4
         Disk Name: /dev/sdl 
         Mount Points: 14.6 TiB Partition   0 /srv/dcache/pools/meta/a/10/data
         Disk Partition Information
            Partition   0: Basic, 14.6 TiB, /srv/dcache/pools/meta/a/10/data
         Logical Drive Label: data-a-10
         Drive Type: Data
         LD Acceleration Method: Controller Cache

      Logical Drive: 13
         Size: 32.00 GB
         Fault Tolerance: 6
         Heads: 255
         Sectors Per Track: 32
         Cylinders: 8225
         Strip Size: 512 KB
         Full Stripe Size: 6144 KB
         Status: Ready for Rebuild
         Unrecoverable Media Errors: None
         MultiDomain Status: OK
         Caching:  Enabled
         Parity Initialization Status: Initialization Completed
         Unique Identifier: 600508B1001C2996BA86CD6677659775
         Disk Name: /dev/sdm 
         Mount Points: 32.0 GiB Partition   0 /srv/dcache/pools/meta/a
         Disk Partition Information
            Partition   0: Basic, 32.0 GiB, /srv/dcache/pools/meta/a
         Logical Drive Label: data-a-meta
         Drive Type: Data
         LD Acceleration Method: Controller Cache


      physicaldrive 1I:1:1
         Port: 1I
         Box: 1
         Bay: 1
         Status: OK
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD2
         Serial Number: ZL2GENW6
         WWID: 5000C500CBD9DBAD
         Model: HPE     MB016000JWZHE
         Current Temperature (C): 32
         Maximum Temperature (C): 35
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBD9DBAF
         Self Encrypting Drive: False

      physicaldrive 1I:1:2
         Port: 1I
         Box: 1
         Bay: 2
         Status: OK
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD2
         Serial Number: ZL2GEK5F
         WWID: 5000C500CBDA9981
         Model: HPE     MB016000JWZHE
         Current Temperature (C): 34
         Maximum Temperature (C): 38
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBDA9983
         Self Encrypting Drive: False

      physicaldrive 1I:1:3
         Port: 1I
         Box: 1
         Bay: 3
         Status: OK
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD2
         Serial Number: ZL2GEMVH
         WWID: 5000C500CBDA0E9D
         Model: HPE     MB016000JWZHE
         Current Temperature (C): 34
         Maximum Temperature (C): 37
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBDA0E9F
         Self Encrypting Drive: False

      physicaldrive 1I:1:4
         Port: 1I
         Box: 1
         Bay: 4
         Status: OK
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD2
         Serial Number: ZL2GEH2Y
         WWID: 5000C500CBDB23B1
         Model: HPE     MB016000JWZHE
         Current Temperature (C): 32
         Maximum Temperature (C): 36
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBDB23B3
         Self Encrypting Drive: False

      physicaldrive 1I:1:5
         Port: 1I
         Box: 1
         Bay: 5
         Status: OK
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD2
         Serial Number: ZL2GEHKT
         WWID: 5000C500CBDB0739
         Model: HPE     MB016000JWZHE
         Current Temperature (C): 34
         Maximum Temperature (C): 38
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBDB073B
         Self Encrypting Drive: False

      physicaldrive 1I:1:6
         Port: 1I
         Box: 1
         Bay: 6
         Status: OK
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD2
         Serial Number: ZL2GEJ5H
         WWID: 5000C500CBDAE221
         Model: HPE     MB016000JWZHE
         Current Temperature (C): 33
         Maximum Temperature (C): 36
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBDAE223
         Self Encrypting Drive: False

      physicaldrive 1I:1:7
         Port: 1I
         Box: 1
         Bay: 7
         Status: OK
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD2
         Serial Number: ZL2GEN4T
         WWID: 5000C500CBDA01D9
         Model: HPE     MB016000JWZHE
         Current Temperature (C): 32
         Maximum Temperature (C): 36
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBDA01DB
         Self Encrypting Drive: False

      physicaldrive 1I:1:8
         Port: 1I
         Box: 1
         Bay: 8
         Status: OK
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD2
         Serial Number: ZL2GEKB6
         WWID: 5000C500CBDA93B5
         Model: HPE     MB016000JWZHE
         Current Temperature (C): 33
         Maximum Temperature (C): 37
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBDA93B7
         Self Encrypting Drive: False

      physicaldrive 1I:1:9
         Port: 1I
         Box: 1
         Bay: 9
         Status: OK
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD2
         Serial Number: ZL2GEKT4
         WWID: 5000C500CBDA5F19
         Model: HPE     MB016000JWZHE
         Current Temperature (C): 31
         Maximum Temperature (C): 35
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBDA5F1B
         Self Encrypting Drive: False

      physicaldrive 1I:1:10
         Port: 1I
         Box: 1
         Bay: 10
         Status: OK
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD2
         Serial Number: ZL2GEJ9S
         WWID: 5000C500CBDAD939
         Model: HPE     MB016000JWZHE
         Current Temperature (C): 31
         Maximum Temperature (C): 35
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBDAD93B
         Self Encrypting Drive: False

      physicaldrive 1I:1:11
         Port: 1I
         Box: 1
         Bay: 11
         Status: OK
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD2
         Serial Number: ZL2GEJW2
         WWID: 5000C500CBDAB015
         Model: HPE     MB016000JWZHE
         Current Temperature (C): 33
         Maximum Temperature (C): 37
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBDAB017
         Self Encrypting Drive: False

      physicaldrive 1I:1:12
         Port: 1I
         Box: 1
         Bay: 12
         Status: OK
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD2
         Serial Number: ZL2GEK34
         WWID: 5000C500CBDA9741
         Model: HPE     MB016000JWZHE
         Current Temperature (C): 31
         Maximum Temperature (C): 35
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBDA9743
         Self Encrypting Drive: False

      physicaldrive 3I:1:13
         Port: 3I
         Box: 1
         Bay: 13
         Status: Rebuilding
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD0
         Serial Number: ZL2GEHXD
         WWID: 5000C500CBDAF03D
         Model: HP      MB016000JWZHE
         Current Temperature (C): 37
         Maximum Temperature (C): 43
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBDAF03F
         Self Encrypting Drive: False

      physicaldrive 3I:1:14
         Port: 3I
         Box: 1
         Bay: 14
         Status: OK
         Drive Type: Data Drive
         Interface Type: SAS
         Size: 16 TB
         Drive exposed to OS: False
         Logical/Physical Block Size: 512/4096
         Rotational Speed: 7200
         Firmware Revision: HPD2
         Serial Number: ZL2GEJHD
         WWID: 5000C500CBDACB85
         Model: HPE     MB016000JWZHE
         Current Temperature (C): 40
         Maximum Temperature (C): 45
         PHY Count: 2
         PHY Transfer Rate: 12.0Gbps, Unknown
         PHY Physical Link Rate: 12.0Gbps, Unknown
         PHY Maximum Link Rate: 12.0Gbps, 12.0Gbps
         Drive Authentication Status: Not Applicable
         Sanitize Erase Supported: True
         Sanitize Estimated Max Erase Time: 25 hour(s), 0 minute(s) 
         Unrestricted Sanitize Supported: True
         Shingled Magnetic Recording Support: None
         Drive Unique ID: 5000C500CBDACB87
         Self Encrypting Drive: False


   Enclosure SEP (Vendor ID HPE, Model Apollo 4200 LFF) 375 
      Device Number: 375
      Firmware Version: 1.79
      WWID: 5001438043D6A63C
      Port: 3I
      Box: 1
      Vendor ID: HPE
      Model: Apollo 4200 LFF

   Enclosure SEP (Vendor ID HPE, Model Apollo 4200 LFF) 376 
      Device Number: 376
      Firmware Version: 1.79
      WWID: 5001438043D60E3C
      Port: 1I
      Box: 1
      Vendor ID: HPE
      Model: Apollo 4200 LFF

   Expander 377 
      Device Number: 377
      Firmware Version: 1.79
      WWID: 5001438043D6A63D
      Port: 3I
      Box: 1
      Vendor ID: HPE

   Expander 378 
      Device Number: 378
      Firmware Version: 1.79
      WWID: 5001438043D60E3D
      Port: 1I
      Box: 1
      Vendor ID: HPE

   SEP (Vendor ID HPE, Model Smart Adapter) 379 
      Device Number: 379
      Firmware Version: 4.11
      WWID: 51402EC0167D2450
      Vendor ID: HPE
      Model: Smart Adapter

[fred-lix]

Bonjour,

I have the same issue with a P408i-a. In rebuid state the output of the plugin was
OK: ssacli:[HPE Smart Array P408i-a SR Gen10[OK]: Array A(OK)[LUN1:Recovering, 6.29% complete]]

In the file hpacucli.pm, I change the ligne } elsif ($s eq 'Rebuild' or $s eq 'Recover') {
to } elsif ($s eq 'Rebuild' or $s eq 'Recover' or $s =~ 'Recovering') {

Maybe just change the line to } elsif ($s eq 'Rebuild' or $s =~ 'Recover') { can also work.

There is probably a better way to do it.

Hope that fix also your problem

Regards,

Frederic