make failing on cygwin

[pran005]

Set up
Provide details of your setup help us to reproduce the issue as quick as possible

• PC OS : Windows 10
• Board : -
• Firmware: examples/device/cdc_msc

Describe the bug
Build failure : Make fails to find the source files when fired from cygwin terminal. Any work around would be really helpful.
To reproduce
Steps to reproduce the behavior:

1. Open cygwin terminal (with make installed)
2. Run make -C examples/device/cdc_msc BOARD=<board_name>
3. See error

Screenshots

[cr1901]

I assume that your C:\Users\Pranjal\Documents\... etc isn't reachable from cygwin's root (/, /home, /bin, /etc). To access C:\Users\Pranjal\Documents\... from cygwin, you need to use /cygdrive/c/Users/Pranjal/, not /c/Users/Pranjal/. I'm not sure the best way to put that into the Makefile.

[pran005]

Thanks for the suggestion but unfortunately, the path you mentioned i.e. /cygdrive/c/Users/Pranjal/ , was causing trouble initially, so I aliased it to /c/Users/Pranjal. You're right that these are not the best paths to put into Makefile, I figured out the issue to be the $(TOP) in the top.mk. (The other makefiles that work use relative paths). Currently, I am not even able to build it under /home.

[hathach]

Although I don't use windows, I guess WSL probably works better than cygwin.

[pran005]

Thanks for the suggestion @hathach ! Can you tell me a preferred development environment if I wish to contribute to the stack? Shall I use Linux and ditch windows?

[hathach]

you should use any environment you feel comfortable with. It is not too important at all.

[pran005]

Alright. Thanks. One more question @hathach , a little unrelated to this topic. Is it absolutely necessary to use the vendor provided drivers as a BSP if I m porting it to a new MCU?

[hathach]

Alright. Thanks. One more question @hathach , a little unrelated to this topic. Is it absolutely necessary to use the vendor provided drivers as a BSP if I m porting it to a new MCU?

You could use any board you have, I tend to go for common/popular one since that is easier for people to get and test.

[kkitayam]

If you are okay with using a non-Cygwin system, examples can be built with msys2 or windows command prompt. I had confirmed at #590

I guess that arm gcc for windows was built with msys2. If gcc was built with cygwin, examples could be built by the gcc on cygwin.

[kkitayam]

I found the same issue on stackoverflow.
It said that arm gcc for windows does not support with cygwin make.

[kkitayam]

I suggest msys2 or command prompt for windows users, because WSL2 does not yet support USB devices. WSL2 can build samples, but it cannot flash them via J-Link. Docker for windows does the same.

[pran005]

Thanks for this @kkitayam . It helped! I tried building it on WSL as suggested by @hathach , it seems to build. But I haven't tried flashing it using J-Link or OpenOCD + ICDI yet. Although I'm able to get that done using cygwin, I can try accessing the same project from WSL & Cygwin for both the things as a ad-hoc solution for now.

As far as command prompt is concerned, I tried installing make using choco pack manager, but the results were similar to that of cygwin. Can you please suggest some other make utility that works fine on command prompt/powershell.

Regards

[kkitayam]

As far as command prompt is concerned, I tried installing make using choco pack manager, but the results were similar to that of cygwin.

I guess that your PATH environment variable has C:\cygwin64\bin for cygwin. The path for cygwin causes failure.
make for windows treats SHELL environment variable as special. Please refer to Choosing-the-Shell
To avoid the issue, would you specify SHELL=cmd.exe on arguments like as following.

C:\> C:\ProgramData\chocolatey\bin\make.exe  SHELL=cmd.exe BOARD=<board_name>

In my investigation is followings.
We can check by where that which make is priority high on PATH environment.
For example, following is in my environment.

C:\>where make
C:\ProgramData\chocolatey\bin\make.exe

I guess @pran005 's environment shows following.

C:\>where make
C:\cygwin64\bin\make.exe
C:\ProgramData\chocolatey\bin\make.exe

I tried to build cdc_msc example in above settings, then that failed.

C:\work\tinyusb\examples\device\cdc_msc>C:\ProgramData\chocolatey\bin\make BOARD=frdm_kl25z
/usr/bin/sh: -c: line 0: syntax error near unexpected token `('
/usr/bin/sh: -c: line 0: `for %%i in ( ../../.. ) do echo %%~fi'
../../make.mk:45: *** Invalid BOARD specified.  Stop.

The message indicates that sh.exe is invoked as a shell because of sh.exe exists on the PATH and not defined SHELL environment variable.

I tried to build with SHELL specified explicitly, then succeeded!

c:\work\tinyusb\examples\device\cdc_msc>C:\ProgramData\chocolatey\bin\make SHELL=cmd.exe BOARD=frdm_kl25z
AS startup_MKL25Z4.o
CC system_MKL25Z4.o
CC clock_config.o
CC fsl_clock.o
... snip
LINK _build/frdm_kl25z/frdm_kl25z-cdc_msc.elf
CREATE _build/frdm_kl25z/frdm_kl25z-cdc_msc.bin
CREATE _build/frdm_kl25z/frdm_kl25z-cdc_msc.hex
''
   text    data     bss     dec     hex filename
  18240    8364    5104   31708    7bdc _build/frdm_kl25z/frdm_kl25z-cdc_msc.elf
''