2ter Wechselrichter Wirkungsgrad bricht ein und schaltet ab

[newganja]

Hallo,

Vielleicht kann mir jemand helfen, habe seit gestern einen 2ten Wechselrichter zu meiner Anlage hinzugefügt und habe nun das Problem das dieser immer wieder abschaltet .
Habe jetzt festgestellt das der Wirkungsgrad von WR bei unter 300W auf unter 50% einbricht, wenn nur 100W bezogen wird bricht dieser ein und schaltet ab.
Mein erster WR (der gleiche wie der 2te Hoymiles 1600) hat damit keine Probleme

[Sorbat]

Was ist denn deine Erwartung, was passiert, wenn dein Strombezug bereits negativ ist?
Oder was hast du konfiguriert?

[newganja]

Nein das problem ist das ich den 2ten WR montiert hab das ich mehr einspeisen kann,
aber wenn der WR sich abschaltet, schaltet er sich nicht mehr ein wenn mehr Last gefordert ist und manchmal wird durch die DPL der erste WR runter geregelt weil er den 2ten noch steuert obwohl dieser aus bzw im Standby ist

[newganja]

Habe nochmal über den Tag geguckt und glaube das Problem ist das die DPL den 2ten wechselrichter wenn last abfällt unter den eingestellten Wert fällt, er geht oft auf 20W oder weniger und schaltet dann ab.

Hier meine DPL Einstellungen ist hier ein Fehler?

[spcqike]

Installiere die mal ne aktuelle Version und dann bräuchte man einen ausführlichen log von der Situation.

[newganja]

Hab die neuste Version installiert aber hab den Fehler immer noch

Hier mal der Log

20:12:29.945 > [DPL inverter 1164a00b1189]:
20:12:30.010 > battery-powered, producing 42 W
20:12:30.074 > lower/current/upper limit: 100/99/700 W, output capability: 1600 W
20:12:30.075 > sending commands enabled, reachable, eligible
20:12:30.140 > max reduction production/standby: 0/42 W, max increase: 601 W
20:12:30.206 > target limit/output/state: 508 W (update)/508 W/production, 0 update timeouts
20:12:30.207 > MPPTs AC power: a: 11 W b: 11 W c: 10 W d: 10 W
20:12:30.280 > [DPL inverter 1164a00e5db8]:
20:12:30.346 > battery-powered, producing 43 W
20:12:30.347 > lower/current/upper limit: 100/99/700 W, output capability: 1600 W
20:12:30.399 > sending commands enabled, reachable, eligible
20:12:30.463 > max reduction production/standby: 0/43 W, max increase: 601 W
20:12:30.512 > target limit/output/state: -1 W (unchanged)/43 W/unchanged, 0 update timeouts
20:12:30.514 > MPPTs AC power: a: 11 W b: 11 W c: 10 W d: 10 W
20:12:30.580 > [DPL inverter 1164a00b1189]: sending limit of 31.8 % (508 W respectively), max output is 1600 W
20:12:30.644 > TX ActivePowerControl (01) 865.00 MHz --> 51 A0 0B 11 89 80 18 73 84 81 0B 00 01 3D 00 01 90 50 7A
20:12:30.701 > [DPL] waiting for a start/stop/restart/limit command to complete
20:12:30.702 > Interrupt received
20:12:30.766 > RX 865.00 MHz --> D1 A0 0B 11 89 80 18 73 84 81 00 00 0B 00 14 07 14 | -34 dBm
20:12:30.837 > Received MQTT message on topic: shellies/shell Solar/emeter/1/power
20:12:30.891 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/1/power': new value: 32.53, total: 393.06
20:12:30.892 > Received MQTT message on topic: shellies/shell Solar/emeter/2/power
20:12:30.960 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/2/power': new value: 239.30, total: 371.07
20:12:31.025 > Fetch inverter: 1164A00E5DB8
20:12:31.078 > Queue size - NRF: 0 CMT: 2
20:12:31.143 > Received MQTT message on topic: shellies/shell Solar/emeter/0/power
20:12:31.209 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/0/power': new value: 99.81, total: 371.64
20:12:31.274 > Received MQTT message on topic: shellies/shell Solar/emeter/1/power
20:12:31.340 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/1/power': new value: -420.00, total: -80.89
20:12:31.341 > Received MQTT message on topic: shellies/shell Solar/emeter/2/power
20:12:31.414 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/2/power': new value: 249.94, total: -70.25
20:12:31.481 > RX Period End
20:12:31.482 > Success
20:12:31.534 > [DPL inverter 1164a00b1189]: actual limit is 31.7 % (507 W respectively), effective 2039 ms after update started, requested were 31.8 %
20:12:31.600 > [DPL] waiting for sufficiently recent inverter data
20:12:31.666 > TX RealTimeRunData 865.00 MHz --> 15 A0 0E 5D B8 80 18 73 84 80 0B 00 67 EE CF 44 00 00 00 00 00 00 00 00 A5 81 9C
20:12:31.667 > Interrupt received
20:12:31.719 > RX 865.00 MHz --> 95 A0 0E 5D B8 80 18 73 84 01 00 01 01 09 01 08 00 49 00 49 00 C3 00 C2 00 00 B1 | -34 dBm
20:12:31.784 > Interrupt received
20:12:31.785 > RX 865.00 MHz --> 95 A0 0E 5D B8 80 18 73 84 02 01 E1 00 00 01 E7 00 03 00 03 01 09 01 09 00 43 F6 | -34 dBm
20:12:31.840 > Interrupt received
20:12:31.906 > RX 865.00 MHz --> 95 A0 0E 5D B8 80 18 73 84 03 00 44 00 B2 00 B4 00 00 01 C6 00 00 01 BF 00 03 8A | -34 dBm
20:12:31.971 > Interrupt received
20:12:31.972 > RX 865.00 MHz --> 95 A0 0E 5D B8 80 18 73 84 04 00 03 09 09 13 88 02 0E 00 00 00 16 03 E8 00 E8 34 | -34 dBm
20:12:32.024 > Interrupt received
20:12:32.089 > RX 865.00 MHz --> 95 A0 0E 5D B8 80 18 73 84 85 00 01 80 D0 65 | -34 dBm
20:12:32.141 > RX Period End
20:12:32.142 > Success
20:12:32.208 > Received MQTT message on topic: shellies/shell Solar/emeter/0/power
20:12:32.274 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/0/power': new value: 98.94, total: -71.12
20:12:32.326 > Received MQTT message on topic: shellies/shell Solar/emeter/1/power
20:12:32.327 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/1/power': new value: -422.10, total: -73.22
20:12:32.392 > Received MQTT message on topic: shellies/shell Solar/emeter/2/power
20:12:32.458 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/2/power': new value: 307.07, total: -16.09
20:12:35.094 > Received MQTT message on topic: shellies/shell Solar/emeter/0/power
20:12:35.157 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/0/power': new value: 97.71, total: -17.32
20:12:35.225 > Received MQTT message on topic: shellies/shell Solar/emeter/1/power
20:12:35.290 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/1/power': new value: -361.10, total: 43.68
20:12:35.342 > Received MQTT message on topic: shellies/shell Solar/emeter/2/power
20:12:35.406 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/2/power': new value: 301.13, total: 37.74
20:12:35.471 > Received MQTT message on topic: shellies/shell Solar/emeter/0/power
20:12:35.537 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/0/power': new value: 97.71, total: 37.74
20:12:35.538 > Received MQTT message on topic: shellies/shell Solar/emeter/1/power
20:12:35.602 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/1/power': new value: -361.10, total: 37.74
20:12:35.667 > Received MQTT message on topic: shellies/shell Solar/emeter/2/power
20:12:35.717 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/2/power': new value: 301.13, total: 37.74
20:12:35.851 > Fetch inverter: 1164A00B1189
20:12:35.913 > Queue size - NRF: 0 CMT: 1
20:12:35.980 > TX RealTimeRunData 865.00 MHz --> 15 A0 0B 11 89 80 18 73 84 80 0B 00 67 EE CF 49 00 00 00 00 00 00 00 00 35 D9 21
20:12:36.048 > Interrupt received
20:12:36.102 > RX 865.00 MHz --> 95 A0 0B 11 89 80 18 73 84 01 00 01 01 07 01 07 02 04 02 07 05 4D 05 56 00 03 D2 | -33 dBm
20:12:36.173 > Interrupt received
20:12:36.240 > RX 865.00 MHz --> 95 A0 0B 11 89 80 18 73 84 02 91 4E 00 03 96 1C 01 17 01 19 01 06 01 07 01 EC 7F | -33 dBm
20:12:36.306 > Interrupt received
20:12:36.307 > RX 865.00 MHz --> 95 A0 0B 11 89 80 18 73 84 03 01 F5 05 07 05 21 00 03 52 C2 00 03 5F 4A 01 10 8C | -33 dBm
20:12:36.372 > Interrupt received
20:12:36.437 > RX 865.00 MHz --> 95 A0 0B 11 89 80 18 73 84 04 01 15 09 17 13 89 13 C3 00 00 00 D9 03 E8 01 4A F4 | -32 dBm
20:12:36.489 > Interrupt received
20:12:36.490 > RX 865.00 MHz --> 95 A0 0B 11 89 80 18 73 84 85 00 04 37 36 49 | -33 dBm
20:12:36.556 > RX Period End
20:12:36.622 > Success
20:12:36.674 > [DPL] waiting for sufficiently recent power meter reading
20:12:36.997 > Admin AP remaining seconds: 50 / 180
20:12:37.065 > Received MQTT message on topic: shellies/shell Solar/emeter/0/power
20:12:37.128 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/0/power': new value: 97.67, total: 37.70
20:12:37.195 > Received MQTT message on topic: shellies/shell Solar/emeter/1/power
20:12:37.269 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/1/power': new value: -412.50, total: -13.70
20:12:37.334 > Received MQTT message on topic: shellies/shell Solar/emeter/2/power
20:12:37.384 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/2/power': new value: 299.58, total: -15.25
20:12:39.093 > Received MQTT message on topic: shellies/shell Solar/emeter/0/power
20:12:39.157 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/0/power': new value: 97.37, total: -15.55
20:12:39.260 > [DPL] up 58 s, next inverter restart at 13800 s (set to 0)
20:12:39.329 > [DPL] battery interface disabled, SoC 0.0 % (used), age 58 s (stale)
20:12:39.391 > [DPL] BMS: -1.00 V, MPPT: -1.00 V, inverter 1164a00b1189: 26.30
20:12:39.457 > [DPL] battery voltage 26.30 V, load-corrected voltage 26.86 V @ 557 W, factor 0.00100 1/A
20:12:39.524 > [DPL] battery discharge allowed, start 26.00 V or 80 %, stop 25.60 V or 20 %
20:12:39.592 > [DPL] start reached, stop NOT reached, solar-passthrough disabled, use at night disabled and dormant
20:12:39.657 > [DPL] total max AC power is 1400 W, conduction losses are 0 %
20:12:39.725 > [DPL] targeting -10 W, base load is 200 W, power meter reads -15.6 W (valid)
20:12:39.790 > [DPL] inverter 1164a00b1189 is behind power meter producing 505 W
20:12:39.856 > [DPL] inverter 1164a00e5db8 is behind power meter producing 52 W
20:12:39.909 > [DPL] granting 551 W from DC power bus (no battery discharge limit), solar power is 0/0 W DC/AC
20:12:39.910 > [DPL] requesting 551 W from 2 battery-powered inverters currently producing 557 W (diff -6 W, hysteresis 25 W)
20:12:39.974 > [DPL inverter 1164a00b1189]:
20:12:40.043 > battery-powered, producing 505 W
20:12:40.110 > lower/current/upper limit: 100/507/700 W, output capability: 1600 W
20:12:40.111 > sending commands enabled, reachable, eligible
20:12:40.176 > max reduction production/standby: 405/505 W, max increase: 193 W
20:12:40.243 > target limit/output/state: -1 W (unchanged)/505 W/unchanged, 0 update timeouts
20:12:40.245 > MPPTs AC power: a: 129 W b: 130 W c: 122 W d: 125 W
20:12:40.309 > [DPL inverter 1164a00e5db8]:
20:12:40.361 > battery-powered, producing 52 W
20:12:40.362 > lower/current/upper limit: 100/99/700 W, output capability: 1600 W
20:12:40.428 > sending commands enabled, reachable, eligible
20:12:40.493 > max reduction production/standby: 0/52 W, max increase: 601 W
20:12:40.546 > target limit/output/state: -1 W (unchanged)/52 W/unchanged, 0 update timeouts
20:12:40.547 > MPPTs AC power: a: 14 W b: 14 W c: 13 W d: 13 W
20:12:40.612 > [DPL] the system is stable, the last power limit is still valid
20:12:40.678 > Received MQTT message on topic: shellies/shell Solar/emeter/1/power
20:12:40.729 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/1/power': new value: -410.27, total: -13.32
20:12:40.731 > Received MQTT message on topic: shellies/shell Solar/emeter/2/power
20:12:40.796 > [PowerMeterMqtt] Topic 'shellies/shell Solar/emeter/2/power': new value: 304.13, total: -8.77
20:12:40.861 > [DPL] up 58 s, next inverter restart at 13800 s (set to 0)
20:12:40.931 > [DPL] battery interface disabled, SoC 0.0 % (used), age 58 s (stale)
20:12:40.983 > [DPL] BMS: -1.00 V, MPPT: -1.00 V, inverter 1164a00b1189: 26.30
20:12:40.984 > [DPL] battery voltage 26.30 V, load-corrected voltage 26.86 V @ 557 W, factor 0.00100 1/A
20:12:41.047 > [DPL] battery discharge allowed, start 26.00 V or 80 %, stop 25.60 V or 20 %
20:12:41.114 > [DPL] start reached, stop NOT reached, solar-passthrough disabled, use at night disabled and dormant
20:12:41.115 > [DPL] total max AC power is 1400 W, conduction losses are 0 %
20:12:41.183 > [DPL] targeting -10 W, base load is 200 W, power meter reads -8.8 W (valid)
20:12:41.242 > [DPL] inverter 1164a00b1189 is behind power meter producing 505 W
20:12:41.309 > [DPL] inverter 1164a00e5db8 is behind power meter producing 52 W
20:12:41.311 > [DPL] granting 558 W from DC power bus (no battery discharge limit), solar power is 0/0 W DC/AC
20:12:41.377 > [DPL] requesting 558 W from 2 battery-powered inverters currently producing 557 W (diff 1 W, hysteresis 25 W)
20:12:41.443 > [DPL inverter 1164a00b1189]:
20:12:41.445 > battery-powered, producing 505 W
20:12:41.496 > lower/current/upper limit: 100/507/700 W, output capability: 1600 W
20:12:41.562 > sending commands enabled, reachable, eligible
20:12:41.625 > max reduction production/standby: 405/505 W, max increase: 193 W
20:12:41.627 > target limit/output/state: -1 W (unchanged)/505 W/unchanged, 0 update timeouts
20:12:41.681 > MPPTs AC power: a: 129 W b: 130 W c: 122 W d: 125 W
20:12:41.748 > [DPL inverter 1164a00e5db8]:
20:12:41.800 > battery-powered, producing 52 W
20:12:41.802 > lower/current/upper limit: 100/99/700 W, output capability: 1600 W
20:12:41.866 > sending commands enabled, reachable, eligible
20:12:41.935 > max reduction production/standby: 0/52 W, max increase: 601 W
20:12:41.988 > target limit/output/state: -1 W (unchanged)/52 W/unchanged, 0 update timeouts
20:12:41.989 > MPPTs AC power: a: 14 W b: 14 W c: 13 W d: 13 W
20:12:42.055 > [DPL] up 59 s, next inverter restart at 13800 s (set to 0)
20:12:42.119 > [DPL] battery interface disabled, SoC 0.0 % (used), age 59 s (stale)
20:12:42.172 > [DPL] BMS: -1.00 V, MPPT: -1.00 V, inverter 1164a00b1189: 26.30
20:12:42.173 > [DPL] battery voltage 26.30 V, load-corrected voltage 26.86 V @ 557 W, factor 0.00100 1/A
20:12:42.241 > [DPL] battery discharge allowed, start 26.00 V or 80 %, stop 25.60 V or 20 %
20:12:42.308 > [DPL] start reached, stop NOT reached, solar-passthrough disabled, use at night disabled and dormant
20:12:42.368 > [DPL] total max AC power is 1400 W, conduction losses are 0 %
20:12:42.369 > [DPL] targeting -10 W, base load is 200 W, power meter reads -8.8 W (valid)
20:12:42.436 > [DPL] inverter 1164a00b1189 is behind power meter producing 505 W
20:12:42.502 > [DPL] inverter 1164a00e5db8 is behind power meter producing 52 W
20:12:42.555 > [DPL] granting 558 W from DC power bus (no battery discharge limit), solar power is 0/0 W DC/AC
20:12:42.556 > [DPL] requesting 558 W from 2 battery-powered inverters currently producing 557 W (diff 1 W, hysteresis 25 W)
20:12:42.622 > [DPL inverter 1164a00b1189]:
20:12:42.690 > battery-powered, producing 505 W
20:12:42.742 > lower/current/upper limit: 100/507/700 W, output capability: 1600 W
20:12:42.809 > sending commands enabled, reachable, eligible
20:12:42.875 > max reduction production/standby: 405/505 W, max increase: 193 W
20:12:42.876 > target limit/output/state: -1 W (unchanged)/505 W/unchanged, 0 update timeouts
20:12:42.945 > MPPTs AC power: a: 129 W b: 130 W c: 122 W d: 125 W
20:12:43.011 > [DPL inverter 1164a00e5db8]:
20:12:43.012 > battery-powered, producing 52 W
20:12:43.065 > lower/current/upper limit: 100/99/700 W, output capability: 1600 W
20:12:43.131 > sending commands enabled, reachable, eligible
20:12:43.183 > max reduction production/standby: 0/52 W, max increase: 601 W
20:12:43.184 > target limit/output/state: -1 W (unchanged)/52 W/unchanged, 0 update timeouts
20:12:43.260 > MPPTs AC power: a: 14 W b: 14 W c: 13 W d: 13 W
20:12:43.328 > Fetch inverter: 1164A00E5DB8
20:12:43.330 > Queue size - NRF: 0 CMT: 1
20:12:43.396 > TX RealTimeRunData 865.00 MHz --> 15 A0 0E 5D B8 80 18 73 84 80 0B 00 67 EE CF 4E 00 00 00 00 00 00 00 00 05 FF 48
20:12:43.456 > [DPL] up 60 s, next inverter restart at 13800 s (set to 0)
20:12:43.457 > [DPL] battery interface disabled, SoC 0.0 % (used), age 60 s (stale)
20:12:43.525 > [DPL] BMS: -1.00 V, MPPT: -1.00 V, inverter 1164a00b1189: 26.30
20:12:43.591 > [DPL] battery voltage 26.30 V, load-corrected voltage 26.86 V @ 557 W, factor 0.00100 1/A
20:12:43.644 > [DPL] battery discharge allowed, start 26.00 V or 80 %, stop 25.60 V or 20 %
20:12:43.646 > [DPL] start reached, stop NOT reached, solar-passthrough disabled, use at night disabled and dormant
20:12:43.711 > [DPL] total max AC power is 1400 W, conduction losses are 0 %
20:12:43.777 > [DPL] targeting -10 W, base load is 200 W, power meter reads -8.8 W (valid)
20:12:43.778 > [DPL] inverter 1164a00b1189 is behind power meter producing 505 W
20:12:43.831 > [DPL] inverter 1164a00e5db8 is behind power meter producing 52 W
20:12:43.897 > [DPL] granting 558 W from DC power bus (no battery discharge limit), solar power is 0/0 W DC/AC
20:12:43.950 > [DPL] requesting 558 W from 2 battery-powered inverters currently producing 557 W (diff 1 W, hysteresis 25 W)
20:12:43.951 > [DPL inverter 1164a00b1189]:
20:12:44.019 > battery-powered, producing 505 W
20:12:44.085 > lower/current/upper limit: 100/507/700 W, output capability: 1600 W
20:12:44.139 > sending commands enabled, reachable, eligible
20:12:44.140 > max reduction production/standby: 405/505 W, max increase: 193 W
20:12:44.207 > target limit/output/state: -1 W (unchanged)/505 W/unchanged, 0 update timeouts
20:12:44.273 > MPPTs AC power: a: 129 W b: 130 W c: 122 W d: 125 W
20:12:44.325 > [DPL inverter 1164a00e5db8]:
20:12:44.326 > battery-powered, producing 52 W
20:12:44.392 > lower/current/upper limit: 100/99/700 W, output capability: 1600 W
20:12:44.458 > sending commands enabled, reachable, eligible
20:12:44.519 > max reduction production/standby: 0/52 W, max increase: 601 W
20:12:44.521 > target limit/output/state: -1 W (unchanged)/52 W/unchanged, 0 update timeouts
20:12:44.588 > MPPTs AC power: a: 14 W b: 14 W c: 13 W d: 13 W
20:12:44.653 > Interrupt received
20:12:44.654 > RX 865.00 MHz --> 95 A0 0E 5D B8 80 18 73 84 01 00 01 01 08 01 08 00 1F 00 1E 00 52 00 51 00 00 B3 | -34 dBm
20:12:44.720 > Interrupt received
20:12:44.772 > RX 865.00 MHz --> 95 A0 0E 5D B8 80 18 73 84 02 01 E1 00 00 01 E7 00 03 00 03 01 08 01 08 00 1D A8 | -34 dBm
20:12:44.838 > Interrupt received
20:12:44.840 > RX 865.00 MHz --> 95 A0 0E 5D B8 80 18 73 84 03 00 1D 00 4E 00 4E 00 00 01 C6 00 00 01 BF 00 03 D5 | -34 dBm
20:12:44.905 > Interrupt received
20:12:44.975 > RX 865.00 MHz --> 95 A0 0E 5D B8 80 18 73 84 04 00 03 09 08 13 88 00 00 00 00 00 00 00 00 00 E8 C4 | -34 dBm
20:12:45.028 > Interrupt received
20:12:45.029 > RX 865.00 MHz --> 95 A0 0E 5D B8 80 18 73 84 85 00 01 34 FD FC | -34 dBm
20:12:45.096 > RX Period End
20:12:45.163 > Success
20:12:45.164 > [DPL] up 61 s, next inverter restart at 13800 s (set to 0)
20:12:45.218 > [DPL] battery interface disabled, SoC 0.0 % (used), age 61 s (stale)
20:12:45.285 > [DPL] BMS: -1.00 V, MPPT: -1.00 V, inverter 1164a00b1189: 26.30
20:12:45.338 > [DPL] battery voltage 26.30 V, load-corrected voltage 26.80 V @ 505 W, factor 0.00100 1/A
20:12:45.339 > [DPL] battery discharge allowed, start 26.00 V or 80 %, stop 25.60 V or 20 %
20:12:45.406 > [DPL] start reached, stop NOT reached, solar-passthrough disabled, use at night disabled and dormant
20:12:45.472 > [DPL] total max AC power is 1400 W, conduction losses are 0 %
20:12:45.526 > [DPL] targeting -10 W, base load is 200 W, power meter reads -8.8 W (valid)
20:12:45.528 > [DPL] inverter 1164a00b1189 is behind power meter producing 505 W
20:12:45.601 > [DPL] inverter 1164a00e5db8 is behind power meter producing 0 W
20:12:45.669 > [DPL] granting 506 W from DC power bus (no battery discharge limit), solar power is 0/0 W DC/AC
20:12:45.723 > [DPL] requesting 506 W from 2 battery-powered inverters currently producing 505 W (diff 1 W, hysteresis 25 W)
20:12:45.724 > [DPL inverter 1164a00b1189]:
20:12:45.791 > battery-powered, producing 505 W
20:12:45.858 > lower/current/upper limit: 100/507/700 W, output capability: 1600 W
20:12:45.912 > sending commands enabled, reachable, eligible
20:12:45.914 > max reduction production/standby: 405/505 W, max increase: 193 W
20:12:45.981 > target limit/output/state: -1 W (unchanged)/505 W/unchanged, 0 update timeouts
20:12:46.047 > MPPTs AC power: a: 129 W b: 130 W c: 122 W d: 125 W
20:12:46.048 > [DPL inverter 1164a00e5db8]:
20:12:46.101 > battery-powered, standing by at 0 W
20:12:46.168 > lower/current/upper limit: 100/99/700 W, output capability: 1600 W
20:12:46.222 > sending commands enabled, reachable, eligible
20:12:46.224 > max reduction production/standby: 0/0 W, max increase: 700 W
20:12:46.291 > target limit/output/state: -1 W (unchanged)/0 W/unchanged, 0 update timeouts
20:12:46.357 > MPPTs AC power: a: 0 W b: 0 W c: 0 W d: 0 W

[schlimmchen]

Weil dieser WR selbst bei 100W Limit nicht stabil läuft, liegt ein Problem an der Hardware vor. Verkabelung oder WR selbst. 100W muss der stabil schaffen (also ohne zu schwingen und ohne wirkunsgradeinbruch).