diff --git a/docs/source/so101.mdx b/docs/source/so101.mdx
index 00ec3eb745..57e8d691d1 100644
--- a/docs/source/so101.mdx
+++ b/docs/source/so101.mdx
@@ -30,131 +30,6 @@ The follower arm uses 6x STS3215 motors with 1/345 gearing. The leader, however,
| Wrist Roll | 5 | 1 / 147 |
| Gripper | 6 | 1 / 147 |
-### Clean Parts
-
-Remove all support material from the 3D-printed parts. The easiest way to do this is using a small screwdriver to get underneath the support material.
-
-It is advisable to install one 3-pin cable in the motor after placing them before continuing assembly.
-
-### Joint 1
-
-- Place the first motor into the base.
-- Fasten the motor with 4 M2x6mm screws (smallest screws). Two from the top and two from the bottom.
-- Slide over the first motor holder and fasten it using two M2x6mm screws (one on each side).
-- Install both motor horns, securing the top horn with a M3x6mm screw.
-- Attach the shoulder part.
-- Tighten the shoulder part with 4 M3x6mm screws on top and 4 M3x6mm screws on the bottom
-- Add the shoulder motor holder.
-
-
-
-
-
-### Joint 2
-
-- Slide the second motor in from the top.
-- Fasten the second motor with 4 M2x6mm screws.
-- Attach both motor horns to motor 2, again use the M3x6mm horn screw.
-- Attach the upper arm with 4 M3x6mm screws on each side.
-
-
-
-
-
-### Joint 3
-
-- Insert motor 3 and fasten using 4 M2x6mm screws
-- Attach both motor horns to motor 3 and secure one again with a M3x6mm horn screw.
-- Connect the forearm to motor 3 using 4 M3x6mm screws on each side.
-
-
-
-
-
-### Joint 4
-
-- Slide over motor holder 4.
-- Slide in motor 4.
-- Fasten motor 4 with 4 M2x6mm screws and attach its motor horns, use a M3x6mm horn screw.
-
-
-
-
-
-### Joint 5
-
-- Insert motor 5 into the wrist holder and secure it with 2 M2x6mm front screws.
-- Install only one motor horn on the wrist motor and secure it with a M3x6mm horn screw.
-- Secure the wrist to motor 4 using 4 M3x6mm screws on both sides.
-
-
-
-
-
-### Gripper / Handle
-
-
-
-
-- Attach the gripper to motor 5, attach it to the motor horn on the wrist using 4 M3x6mm screws.
-- Insert the gripper motor and secure it with 2 M2x6mm screws on each side.
-- Attach the motor horns and again use a M3x6mm horn screw.
-- Install the gripper claw and secure it with 4 M3x6mm screws on both sides.
-
-
-
-
-
-
-
-
-- Mount the leader holder onto the wrist and secure it with 4 M3x6mm screws.
-- Attach the handle to motor 5 using 1 M2x6mm screw.
-- Insert the gripper motor, secure it with 2 M2x6mm screws on each side, attach a motor horn using a M3x6mm horn screw.
-- Attach the follower trigger with 4 M3x6mm screws.
-
-
-
-
-
-
-
-
## Configure the motors
### 1. Find the USB ports associated with each arm
@@ -340,6 +215,131 @@ leader.setup_motors()
+### Clean Parts
+
+Remove all support material from the 3D-printed parts. The easiest way to do this is using a small screwdriver to get underneath the support material.
+
+It is advisable to install one 3-pin cable in the motor after placing them before continuing assembly.
+
+### Joint 1
+
+- Place the first motor into the base.
+- Fasten the motor with 4 M2x6mm screws (smallest screws). Two from the top and two from the bottom.
+- Slide over the first motor holder and fasten it using two M2x6mm screws (one on each side).
+- Install both motor horns, securing the top horn with a M3x6mm screw.
+- Attach the shoulder part.
+- Tighten the shoulder part with 4 M3x6mm screws on top and 4 M3x6mm screws on the bottom
+- Add the shoulder motor holder.
+
+
+
+
+
+### Joint 2
+
+- Slide the second motor in from the top.
+- Fasten the second motor with 4 M2x6mm screws.
+- Attach both motor horns to motor 2, again use the M3x6mm horn screw.
+- Attach the upper arm with 4 M3x6mm screws on each side.
+
+
+
+
+
+### Joint 3
+
+- Insert motor 3 and fasten using 4 M2x6mm screws
+- Attach both motor horns to motor 3 and secure one again with a M3x6mm horn screw.
+- Connect the forearm to motor 3 using 4 M3x6mm screws on each side.
+
+
+
+
+
+### Joint 4
+
+- Slide over motor holder 4.
+- Slide in motor 4.
+- Fasten motor 4 with 4 M2x6mm screws and attach its motor horns, use a M3x6mm horn screw.
+
+
+
+
+
+### Joint 5
+
+- Insert motor 5 into the wrist holder and secure it with 2 M2x6mm front screws.
+- Install only one motor horn on the wrist motor and secure it with a M3x6mm horn screw.
+- Secure the wrist to motor 4 using 4 M3x6mm screws on both sides.
+
+
+
+
+
+### Gripper / Handle
+
+
+
+
+- Attach the gripper to motor 5, attach it to the motor horn on the wrist using 4 M3x6mm screws.
+- Insert the gripper motor and secure it with 2 M2x6mm screws on each side.
+- Attach the motor horns and again use a M3x6mm horn screw.
+- Install the gripper claw and secure it with 4 M3x6mm screws on both sides.
+
+
+
+
+
+
+
+
+- Mount the leader holder onto the wrist and secure it with 4 M3x6mm screws.
+- Attach the handle to motor 5 using 1 M2x6mm screw.
+- Insert the gripper motor, secure it with 2 M2x6mm screws on each side, attach a motor horn using a M3x6mm horn screw.
+- Attach the follower trigger with 4 M3x6mm screws.
+
+
+
+
+
+
+
+
## Calibrate
Next, you'll need to calibrate your robot to ensure that the leader and follower arms have the same position values when they are in the same physical position.