clk: Fix typos

Fix typos, mostly in comments except CLKGATE_SEPERATED_* (definition and
uses updated).

Signed-off-by: Bjorn Helgaas <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Stephen Boyd <[email protected]>

Author: bjorn-helgaas

drivers/clk/baikal-t1/clk-ccu-div.c

@@ -405,7 +405,7 @@ static void ccu_div_clk_unregister(struct ccu_div_data *data, bool defer)
 {
 	int idx;
 
-	/* Uninstall only the clocks registered on the specfied stage */
+	/* Uninstall only the clocks registered on the specified stage */
 	for (idx = 0; idx < data->divs_num; ++idx) {
 		if (!!(data->divs_info[idx].features & CCU_DIV_BASIC) ^ defer)
 			continue;

drivers/clk/baikal-t1/clk-ccu-pll.c

@@ -196,7 +196,7 @@ static void ccu_pll_clk_unregister(struct ccu_pll_data *data, bool defer)
 {
 	int idx;
 
-	/* Uninstall only the clocks registered on the specfied stage */
+	/* Uninstall only the clocks registered on the specified stage */
 	for (idx = 0; idx < CCU_PLL_NUM; ++idx) {
 		if (!!(pll_info[idx].features & CCU_PLL_BASIC) ^ defer)
 			continue;

drivers/clk/bcm/clk-bcm2835.c

@@ -1555,7 +1555,7 @@ static const char *const bcm2835_clock_osc_parents[] = {
 	.parents = bcm2835_clock_osc_parents,				\
 	__VA_ARGS__)
 
-/* main peripherial parent mux */
+/* main peripheral parent mux */
 static const char *const bcm2835_clock_per_parents[] = {
 	"gnd",
 	"xosc",

drivers/clk/bcm/clk-bcm53573-ilp.c

@@ -59,7 +59,7 @@ static unsigned long bcm53573_ilp_recalc_rate(struct clk_hw *hw,
 	/*
 	 * At minimum we should loop for a bit to let hardware do the
 	 * measurement. This isn't very accurate however, so for a better
-	 * precision lets try getting 20 different values for and use average.
+	 * precision let's try getting 20 different values and use average.
 	 */
 	while (num < 20) {
 		regmap_read(regmap, PMU_XTAL_FREQ_RATIO, &cur_val);

drivers/clk/berlin/berlin2-avpll.c

@@ -319,7 +319,7 @@ berlin2_avpll_channel_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
 
 	/*
 	 * AV3 divider start at VCO_CTRL14, bit 7; each 4 bits wide.
-	 * AV2/AV3 form a fractional divider, where only specfic values for AV3
+	 * AV2/AV3 form a fractional divider, where only specific values for AV3
 	 * are allowed. AV3 != 0 divides by AV2/2, AV3=0 is bypass.
 	 */
 	if (ch->index < 6) {

drivers/clk/clk-asm9260.c

@@ -92,8 +92,8 @@ static const struct asm9260_div_clk asm9260_div_clks[] __initconst = {
 	{ CLKID_SYS_CPU,	"cpu_div", "main_gate", HW_CPUCLKDIV },
 	{ CLKID_SYS_AHB,	"ahb_div", "cpu_div", HW_SYSAHBCLKDIV },
 
-	/* i2s has two deviders: one for only external mclk and internal
-	 * devider for all clks. */
+	/* i2s has two dividers: one for only external mclk and internal
+	 * divider for all clks. */
 	{ CLKID_SYS_I2S0M,	"i2s0m_div", "i2s0_mclk",  HW_I2S0MCLKDIV },
 	{ CLKID_SYS_I2S1M,	"i2s1m_div", "i2s1_mclk",  HW_I2S1MCLKDIV },
 	{ CLKID_SYS_I2S0S,	"i2s0s_div", "i2s0_gate",  HW_I2S0SCLKDIV },

drivers/clk/clk-ast2600.c

@@ -92,7 +92,7 @@ static u8 soc_rev;
  *
  * There are some gates that do not have an associated reset; these are
  * handled by using -1 as the index for the reset, and the consumer must
- * explictly assert/deassert reset lines as required.
+ * explicitly assert/deassert reset lines as required.
  *
  * Clocks marked with CLK_IS_CRITICAL:
  *

drivers/clk/clk-axi-clkgen.c

@@ -172,7 +172,7 @@ static void axi_clkgen_calc_params(const struct axi_clkgen_limits *limits,
 		}
 	}
 
-	/* Lets see if we find a better setting in fractional mode */
+	/* Let's see if we find a better setting in fractional mode */
 	if (fract_shift == 0) {
 		fract_shift = 3;
 		goto again;

drivers/clk/clk-clps711x.c

@@ -99,7 +99,7 @@ static void __init clps711x_clk_init_dt(struct device_node *np)
 	 */
 	tmp &= ~(SYSCON1_TC1M | SYSCON1_TC1S);
 	/* Timer2 in prescale mode.
-	 * Value writen is automatically re-loaded when
+	 * Value written is automatically re-loaded when
 	 * the counter underflows.
 	 */
 	tmp |= SYSCON1_TC2M | SYSCON1_TC2S;

drivers/clk/clk-eyeq.c

@@ -131,7 +131,7 @@ struct eqc_early_match_data {
  * Both factors (mult and div) must fit in 32 bits. When an operation overflows,
  * this function throws away low bits so that factors still fit in 32 bits.
  *
- * Precision loss depends on amplitude of mult and div. Worst theorical
+ * Precision loss depends on amplitude of mult and div. Worst theoretical
  * loss is: (UINT_MAX+1) / UINT_MAX - 1 = 2.3e-10.
  * This is 1Hz every 4.3GHz.
  */