Merge tag 'soc-drivers-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull SoC driver updates from Arnd Bergmann:
 "Changes are all over the place, but very little sticks out as
  noteworthy.

  There is a new misc driver for the Raspberry Pi 5's RP1 multifunction
  I/O chip, along with hooking it up to the pinctrl and clk frameworks.

  The reset controller and memory subsystems have mainly small updates,
  but there are two new reset drivers for the K230 and VC1800B SoCs, and
  new memory driver support for Tegra264.

  The ARM SMCCC and SCMI firmware drivers gain a few more features that
  should help them be supported across more environments. Similarly, the
  SoC specific firmware on Tegra and Qualcomm get minor enhancements and
  chip support.

  In the drivers/soc/ directory, the ASPEED LPC snoop driver gets an
  overhaul for code robustness, the Tegra and Qualcomm and NXP drivers
  grow to support more chips, while the Hisilicon, Mediatek and Renesas
  drivers see mostly janitorial fixes"

* tag 'soc-drivers-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (100 commits)
  bus: del unnecessary init var
  soc: fsl: qe: convert set_multiple() to returning an integer
  pinctrl: rp1: use new GPIO line value setter callbacks
  soc: hisilicon: kunpeng_hccs: Fix incorrect log information
  dt-bindings: soc: qcom: qcom,pmic-glink: document Milos compatible
  dt-bindings: soc: qcom,aoss-qmp: document the Milos Always-On Subsystem side channel
  dt-bindings: firmware: qcom,scm: document Milos SCM Firmware Interface
  soc: qcom: socinfo: Add support to retrieve APPSBL build details
  soc: qcom: pmic_glink: fix OF node leak
  soc: qcom: spmi-pmic: add more PMIC SUBTYPE IDs
  soc: qcom: socinfo: Add PM7550 & PMIV0108 PMICs
  soc: qcom: socinfo: Add SoC IDs for SM7635 family
  dt-bindings: arm: qcom,ids: Add SoC IDs for SM7635 family
  firmware: qcom: scm: request the waitqueue irq *after* initializing SCM
  firmware: qcom: scm: initialize tzmem before marking SCM as available
  firmware: qcom: scm: take struct device as argument in SHM bridge enable
  firmware: qcom: scm: remove unused arguments from SHM bridge routines
  soc: qcom: rpmh-rsc: Add RSC version 4 support
  memory: tegra: Add Tegra264 MC and EMC support
  firmware: tegra: bpmp: Fix build failure for tegra264-only config
  ...

Author: torvalds

Documentation/devicetree/bindings/arm/cpus.yaml

@@ -200,6 +200,7 @@ properties:
       - qcom,kryo385
       - qcom,kryo465
       - qcom,kryo468
+      - qcom,kryo470
       - qcom,kryo485
       - qcom,kryo560
       - qcom,kryo570

Documentation/devicetree/bindings/firmware/qcom,scm.yaml

@@ -32,6 +32,7 @@ properties:
           - qcom,scm-ipq8074
           - qcom,scm-ipq9574
           - qcom,scm-mdm9607
+          - qcom,scm-milos
           - qcom,scm-msm8226
           - qcom,scm-msm8660
           - qcom,scm-msm8916
@@ -198,6 +199,7 @@ allOf:
           compatible:
             contains:
               enum:
+                - qcom,scm-milos
                 - qcom,scm-sm8450
                 - qcom,scm-sm8550
                 - qcom,scm-sm8650

Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt

@@ -0,0 +1,222 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/arm,pl172.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ARM PL172/PL175/PL176 MultiPort Memory Controller
+
+maintainers:
+  - Frank Li <[email protected]>
+
+# We need a select here so we don't match all nodes with 'arm,primecell'
+select:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - arm,pl172
+          - arm,pl175
+          - arm,pl176
+  required:
+    - compatible
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - arm,pl172
+          - arm,pl175
+          - arm,pl176
+      - const: arm,primecell
+
+  reg:
+    maxItems: 1
+
+  '#address-cells':
+    const: 2
+
+  '#size-cells':
+    const: 1
+
+  ranges: true
+
+  clocks:
+    maxItems: 2
+
+  clock-names:
+    items:
+      - const: mpmcclk
+      - const: apb_pclk
+
+  clock-ranges: true
+
+  resets:
+    maxItems: 1
+
+patternProperties:
+  "^cs[0-9]$":
+    type: object
+    additionalProperties: false
+    patternProperties:
+      "^flash@[0-9],[0-9a-f]+$":
+        type: object
+        $ref: /schemas/mtd/mtd-physmap.yaml#
+        unevaluatedProperties: false
+
+      "^(gpio|sram)@[0-9],[0-9a-f]+$":
+        type: object
+        additionalProperties: true
+
+    properties:
+      '#address-cells':
+        const: 2
+
+      '#size-cells':
+        const: 1
+
+      ranges: true
+
+      clocks:
+        maxItems: 2
+
+      clock-ranges: true
+
+      mpmc,cs:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description:
+          Chip select number. Indicates to the pl0172 driver
+          which chipselect is used for accessing the memory.
+
+      mpmc,memory-width:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [8, 16, 32]
+        description:
+          Width of the chip select memory. Must be equal to either 8, 16 or 32.
+
+      mpmc,async-page-mode:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Enable asynchronous page mode.
+
+      mpmc,cs-active-high:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Set chip select polarity to active high.
+
+      mpmc,byte-lane-low:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Set byte lane state to low.
+
+      mpmc,extended-wait:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Enable extended wait.
+
+      mpmc,buffer-enable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Enable write buffer, option is not supported by
+          PL175 and PL176 controllers.
+
+      mpmc,write-protect:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Enable write protect.
+
+      mpmc,read-enable-delay:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description:
+          Delay from chip select assertion to read
+          enable (RE signal) in nano seconds.
+
+      mpmc,write-enable-delay:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description:
+          Delay from chip select assertion to write
+          enable (WE signal) in nano seconds.
+
+      mpmc,output-enable-delay:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description:
+          Delay from chip select assertion to output
+          enable (OE signal) in nano seconds.
+
+      mpmc,write-access-delay:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description:
+          Delay from chip select assertion to write
+          access in nano seconds.
+
+      mpmc,read-access-delay:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description:
+          Delay from chip select assertion to read
+          access in nano seconds.
+
+      mpmc,page-mode-read-delay:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description:
+          Delay for asynchronous page mode sequential
+          accesses in nano seconds.
+
+      mpmc,turn-round-delay:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description:
+          Delay between access to memory banks in nano
+          seconds.
+
+required:
+  - compatible
+  - reg
+  - '#address-cells'
+  - '#size-cells'
+  - ranges
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/lpc18xx-ccu.h>
+
+    memory-controller@40005000 {
+        compatible = "arm,pl172", "arm,primecell";
+        reg = <0x40005000 0x1000>;
+        clocks = <&ccu1 CLK_CPU_EMCDIV>, <&ccu1 CLK_CPU_EMC>;
+        clock-names = "mpmcclk", "apb_pclk";
+        #address-cells = <2>;
+        #size-cells = <1>;
+        ranges = <0 0 0x1c000000 0x1000000
+                  1 0 0x1d000000 0x1000000
+                  2 0 0x1e000000 0x1000000
+                  3 0 0x1f000000 0x1000000>;
+
+        cs0 {
+            #address-cells = <2>;
+            #size-cells = <1>;
+            ranges;
+
+            mpmc,cs = <0>;
+            mpmc,memory-width = <16>;
+            mpmc,byte-lane-low;
+            mpmc,write-enable-delay = <0>;
+            mpmc,output-enable-delay = <0>;
+            mpmc,read-enable-delay = <70>;
+            mpmc,page-mode-read-delay = <70>;
+
+            flash@0,0 {
+                compatible = "sst,sst39vf320", "cfi-flash";
+                reg = <0 0 0x400000>;
+                bank-width = <2>;
+                #address-cells = <1>;
+                #size-cells = <1>;
+                partition@0 {
+                    label = "data";
+                    reg = <0 0x400000>;
+                };
+            };
+        };
+    };