arm64: dts: ti: k3-am62a7-sk: add boot phase tags

The 'bootph-all' tag was added to the dt-schema to describe the various
nodes used during the different phases of bootup with DT. Add the
bootph-all tag to all nodes that are used during the early stages of
bootup by the bootloaders.

This includes the console UART along with the SD and eMMC nodes and its
required regulators for the 3v3 to 1v8 transition and the various nodes
for Ethernet booting.

Signed-off-by: Bryan Brattlof <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vignesh Raghavendra <[email protected]>

Author: bryanbrattlof

arch/arm64/boot/dts/ti/k3-am62a7-sk.dts

@@ -36,6 +36,7 @@
 		/* 4G RAM */
 		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
 		      <0x00000008 0x80000000 0x00000000 0x80000000>;
+		bootph-all;
 	};
 
 	reserved-memory {
@@ -151,6 +152,7 @@
 		regulator-boot-on;
 		enable-active-high;
 		gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
+		bootph-all;
 	};
 
 	vcc_3v3_sys: regulator-4 {
@@ -297,6 +299,7 @@
 			AM62AX_IOPAD(0x1c8, PIN_INPUT, 0) /* (E14) UART0_RXD */
 			AM62AX_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (D15) UART0_TXD */
 		>;
+		bootph-all;
 	};
 
 	main_uart1_pins_default: main-uart1-default-pins {
@@ -320,6 +323,7 @@
 			AM62AX_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
 			AM62AX_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
 		>;
+		bootph-all;
 	};
 
 	main_i2c2_pins_default: main-i2c2-default-pins {
@@ -356,6 +360,7 @@
 			AM62AX_IOPAD(0x224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */
 			AM62AX_IOPAD(0x240, PIN_INPUT, 0) /* (D17) MMC1_SDCD */
 		>;
+		bootph-all;
 	};
 
 	usr_led_pins_default: usr-led-default-pins {
@@ -375,6 +380,7 @@
 			AM62AX_IOPAD(0x160, PIN_OUTPUT, 0) /* (V12) MDIO0_MDC */
 			AM62AX_IOPAD(0x15c, PIN_INPUT, 0) /* (V13) MDIO0_MDIO */
 		>;
+		bootph-all;
 	};
 
 	main_rgmii1_pins_default: main-rgmii1-default-pins {
@@ -392,6 +398,7 @@
 			AM62AX_IOPAD(0x130, PIN_INPUT, 0) /* (AB17) RGMII1_TXC */
 			AM62AX_IOPAD(0x12c, PIN_INPUT, 0) /* (W16) RGMII1_TX_CTL */
 		>;
+		bootph-all;
 	};
 
 	main_mcasp1_pins_default: main-mcasp1-default-pins {
@@ -572,6 +579,7 @@
 		#interrupt-cells = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
+		bootph-all;
 
 		gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
 				   "BT_EN_SOC", "MMC1_SD_EN",
@@ -675,10 +683,12 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mmc1_pins_default>;
 	disable-wp;
+	bootph-all;
 };
 
 &main_gpio0 {
 	status = "okay";
+	bootph-all;
 };
 
 &main_gpio1 {
@@ -693,6 +703,7 @@
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart0_pins_default>;
+	bootph-all;
 };
 
 /* Main UART1 is used for TIFS firmware logs */
@@ -739,10 +750,15 @@
 	pinctrl-0 = <&main_rgmii1_pins_default>;
 };
 
+&phy_gmii_sel {
+	bootph-all;
+};
+
 &cpsw_port1 {
 	status = "okay";
 	phy-mode = "rgmii-rxid";
 	phy-handle = <&cpsw3g_phy0>;
+	bootph-all;
 };
 
 &cpsw_port2 {
@@ -759,6 +775,7 @@
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
 		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
 		ti,min-output-impedance;
+		bootph-all;
 	};
 };