[AMDGPU] Prefer s_memtime for readcyclecounter on GFX10 (#80211)

Summary:
The old `s_memtime` instruction was supported until the GFX10
architecture. Although this instruction has a higher latency than the
new shader counter, it's much more usable as a processor clock as it is
a full 64-bit counter. The new shader counter is only a 20-bit counter,
which makes it difficult to use as a standard cycle counter as it will
overflow in a few milliseconds. This patch suggests preferring
`s_memtime` for this instrinsic if it is still available.

Author: jhuber6

llvm/lib/Target/AMDGPU/SMInstructions.td

@@ -1065,8 +1065,6 @@ def : GCNPat <
   (REG_SEQUENCE SReg_64,
     (S_GETREG_B32 getHwRegImm<HWREG.SHADER_CYCLES, 0, -12>.ret), sub0,
     (S_MOV_B32 (i32 0)), sub1)> {
-  // Prefer this to s_memtime because it has lower and more predictable latency.
-  let AddedComplexity = 1;
 }
 } // let OtherPredicates = [HasShaderCyclesRegister]
 

llvm/test/CodeGen/AMDGPU/readcyclecounter.ll

@@ -4,8 +4,8 @@
 ; RUN: llc -global-isel=1 -mtriple=amdgcn -mcpu=tonga -verify-machineinstrs < %s | FileCheck -check-prefix=MEMTIME -check-prefix=SIVI -check-prefix=GCN %s
 ; RUN: llc -global-isel=0 -mtriple=amdgcn -mcpu=gfx1010 -verify-machineinstrs < %s | FileCheck -check-prefix=MEMTIME -check-prefix=GCN %s
 ; RUN: llc -global-isel=1 -mtriple=amdgcn -mcpu=gfx1010 -verify-machineinstrs < %s | FileCheck -check-prefix=MEMTIME -check-prefix=GCN %s
-; RUN: llc -global-isel=0 -mtriple=amdgcn -mcpu=gfx1030 -verify-machineinstrs < %s | FileCheck -check-prefixes=GETREG,GETREG-SDAG -check-prefix=GCN %s
-; RUN: llc -global-isel=1 -mtriple=amdgcn -mcpu=gfx1030 -verify-machineinstrs < %s | FileCheck -check-prefixes=GETREG,GETREG-GISEL -check-prefix=GCN %s
+; RUN: llc -global-isel=0 -mtriple=amdgcn -mcpu=gfx1030 -verify-machineinstrs < %s | FileCheck -check-prefixes=MEMTIME -check-prefix=GCN %s
+; RUN: llc -global-isel=1 -mtriple=amdgcn -mcpu=gfx1030 -verify-machineinstrs < %s | FileCheck -check-prefixes=MEMTIME -check-prefix=GCN %s
 ; RUN: llc -global-isel=0 -mtriple=amdgcn -mcpu=gfx1100 -verify-machineinstrs -amdgpu-enable-vopd=0 < %s | FileCheck -check-prefixes=GETREG,GETREG-SDAG -check-prefix=GCN %s
 ; RUN: llc -global-isel=1 -mtriple=amdgcn -mcpu=gfx1100 -verify-machineinstrs -amdgpu-enable-vopd=0 < %s | FileCheck -check-prefixes=GETREG,GETREG-GISEL -check-prefix=GCN %s
 ; RUN: llc -global-isel=0 -mtriple=amdgcn -mcpu=gfx1200 -verify-machineinstrs < %s | FileCheck -check-prefixes=GCN,GFX12 %s