m5stack core2 builds but screen flashes (boot loop)

[wegunterjr]

I was able to build and flash on an m5stack core2 aws but when it runs it just seems to boot loop:

[     0][E][vfs_api.cpp:22] open(): File system is not mounted
[     0][D][Button.cpp:42] Button(): Button on pin 255, invert=1, debounce=10ms
[     0][D][Button.cpp:42] Button(): Button on pin 255, invert=1, debounce=10ms
[     0][D][Button.cpp:42] Button(): Button on p��� 255, invert=1, debounce=10ms
[     1][D][esp32-hal-cpu.c:211] setCpuFrequencyMhz(): PLL: 480 / 2 = 240 Mhz, APB: 80000000 Hz
[   850][D][esp32-hal-psram.c:84] psramInit(): PSRAM enabled
ESP32-Chimera-Core initializing [Board=M5Stack Core2] [Variant=m5stack_core2] 
[   943][W][AXP192.cpp:17] begin(): [ AXP ]
[   944][D][AXP192.cpp:21] begin():   - VBUS limit off
[   947][D][AXP192.cpp:25] begin():   - GPIO1 init
[   951][D][AXP192.cpp:29] begin():   - GPIO2 init
[   956][W][AXP192.cpp:33] begin():   - RTC battery charging enabled
[   962][W][AXP192.cpp:36] begin():   - ESP32 power voltage was set to 3.35v
[   969][W][AXP192.cpp:39] begin():   - TFT backlight voltage was set to 2.80v
[   976][W][AXP192.cpp:42] begin():   - TFT logic and SDCard voltage preset to 3.3v
[   983][W][AXP192.cpp:45] begin():   - Vibrator voltage preset to 2v
[   989][W][AXP192.cpp:50] begin():   - M5Go CHG Base current set to 100mA
[   996][D][AXP192.cpp:56] begin():   - GPIO4 init
[  1202][D][ESP32-Chimera-Core.cpp:93] begin(): Enabling LCD
[  1204][W][LGFX_AutoDetect_ESP32.hpp:809] autodetect(): AXP192 found.
[  1209][W][LGFX_AutoDetect_ESP32.hpp:415] _read_panel_id(): [Autodetect] read cmd:04 = 7f0000e3
[  1212][W][LGFX_AutoDetect_ESP32.hpp:907] autodetect(): [Autodetect] M5StackCore2
[  1371][D][ESP32-Chimera-Core.cpp:276] sd_begin(): Enabling SD from TFCARD_CS_PIN #4 at 25000000 Hz from core #1
[  1375][W][sd_diskio.cpp:174] sdCommand(): no token received
[  1477][W][sd_diskio.cpp:174] sdCommand(): no token received
[  1578][W][sd_diskio.cpp:174] sdCommand(): no token received
[  1679][E][sd_diskio.cpp:199] sdCommand(): Card Failed! cmd: 0x00
[  1679][W][sd_diskio.cpp:510] ff_sd_initialize(): GO_IDLE_STATE failed
[  1680][E][sd_diskio.cpp:790] sdcard_mount(): f_mount failed: (3) The physical drive cannot work
[  1689][W][sd_diskio.cpp:174] sdCommand(): no token received
[  1794][W][sd_diskio.cpp:174] sdCommand(): no token received
[  1895][W][sd_diskio.cpp:174] sdCommand(): no token received
[  1996][E][sd_diskio.cpp:199] sdCommand(): Card Failed! cmd: 0x00
[  1996][D][RTC_BM8563.cpp:26] begin(): [RTC BM8563] Begin (port=Wire1, SDA=21, SCL=22, freq=400000)
[  2012][W][ESP32-Chimera-Core.cpp:358] setSystemTimeFromRtc(): System time could not be adjusted from RTC
ESP32-Chimera-Core started
Exception in thread rx: