💡 [REQUEST] - <title>looking for a config file to convert my printer to klipper

[erikaSKOOL]

Reference Issues

No response

Summary

marlin is too much for me and i plan to switch to a different bootloader and everything and go to klipper

Basic Example

config.h

[AuroraViola]

For the Dreamer NX and Dreamer, you need to use this fork of Klipper. You also need an ST-link to flash it. You can wipe the stock bootloader and flash directly the .bin

Here is my printer.cfg for my flashforge dreamer NX (note that LED wont work and also the screen wont work and extruder rotation distance may be wrong):

[include mainsail.cfg]
[mcu]
serial: /dev/serial/by-id/usb-Klipper_stm32f407xx_2B001B000547373433343039-if00

[virtual_sdcard]
path: /home/pi/printer_data/gcodes
on_error_gcode: CANCEL_PRINT

[printer]
kinematics: cartesian
max_velocity: 1000
max_accel: 1000

[stepper_x]
step_pin: PB4
dir_pin: !PB3
enable_pin: !PB6
microsteps: 16
rotation_distance: 36
endstop_pin: ^!PF3
position_endstop: 158.50
position_min: -111.00
position_max: 158.50
homing_speed: 50

[stepper_y]
step_pin: PB8
dir_pin: !PB7
enable_pin: !PE0
microsteps: 16
rotation_distance: 36
endstop_pin: ^!PF2
position_endstop: 76.23
position_min: -76.23
position_max: 76.23
homing_speed: 50

[stepper_z]
step_pin: PE6
dir_pin: !PE5
enable_pin: !PF4
microsteps: 16
rotation_distance: 8
endstop_pin: !PE4
position_endstop: 0
position_max: 144
position_min: 0

[ads1118]
sensor_pin: PA4
spi_software_miso_pin: PA6
spi_software_sclk_pin: PA5
spi_software_mosi_pin: PA7

[extruder]
step_pin: PC2
dir_pin: !PC1
enable_pin: !PC3
microsteps: 16
rotation_distance: 32.857
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA3
sensor_type: ads1118_typek
sensor_pin: ads1118:pin_0
min_temp: 0
max_temp: 260
#control: pid
#pid_kp: 27.746
#pid_ki: 1.666
#pid_kd: 115.493
max_extrude_only_distance: 101

[mcp4018 current_x]
scl_pin: PF12
sda_pin: PB5
wiper: 0.8

[mcp4018 current_y]
scl_pin: PF12
sda_pin: PB9
wiper: 0.8

[mcp4018 current_z]
scl_pin: PF12
sda_pin: PF0
wiper: 0.35

[mcp4018 current_e0]
scl_pin: PF12
sda_pin: PA0
wiper: 0.6

[mcp4018 current_e1]
scl_pin: PF12
sda_pin: PF10
wiper: 0.6


[heater_fan extruder_fan]
pin: PC0
heater: extruder

[fan]
pin: PF5

[fan_generic enclosure_fan]
pin: PE1
cycle_time: 0.01

[temperature_sensor enclosure_temp]
sensor_type: Generic 3950
sensor_pin: PC4

[heater_bed]
heater_pin: PA1
sensor_type: Generic 3950
sensor_pin: PC5
#control: pid
#pid_Kp: 70.037
#pid_Ki: 1.710
#pid_Kd: 717.000
min_temp: -250
max_temp: 250

[pwm_cycle_time beeper]
pin: PB0
value: 0
shutdown_value: 0
scale: 1

# [pca9632 led]
# i2c_software_scl_pin: PF12
# i2c_software_sda_pin: PB1
# color_order: RBGW
# initial_BLUE:  0.3
# initial_GREEN: 0.3
# initial_RED:   1.0

[mcu rpi]
serial: /tmp/klipper_host_mcu

[bltouch]
sensor_pin: ^rpi:gpio0
control_pin: rpi:gpio17
z_offset: 0.2

[mpu9250]
i2c_mcu: rpi
i2c_bus: i2c.1

[resonance_tester]
accel_chip: mpu9250
probe_points:
    0, 0, 20

[gcode_macro M300]
gcode:
    # Use a default 1kHz tone if S is omitted.
    {% set S = params.S|default(1000)|int %}
    # Use a 10ms duration is P is omitted.
    {% set P = params.P|default(100)|int %}
    {% set W = params.W|default(100)|int %}
    SET_PIN PIN=beeper VALUE={W/200.0} CYCLE_TIME={ 1.0/S if S > 0 else 1 }
    G4 P{P}
    SET_PIN PIN=beeper VALUE=0

[delayed_gcode startup_sound]
initial_duration: 0.1
gcode:
  M300 P200 S1050
  G4 P200
  M300 P100 S1200
  G4 P100
  M300 P200 S1400
  G4 P200
  M300 P100 S1650
  G4 P100
  M300 P200 S1850
  G4 P200
  M300 P200 S1650
  G4 P200
  M300 P200 S1650
  G4 P200
  M300 P200 S2100


[exclude_object]

[rajsris]

What steps need to be taken next to get the LED to work (besides uncommenting here, of course)!

[rajsris]

For the Dreamer NX and Dreamer, you need to use this fork of Klipper. You also need an ST-link to flash it. You can wipe the stock bootloader and flash directly the .bin

After doing make menu config , I chose stm32F407. I then tried to flash this to the printer via ST-Link at 0x08010000 and rebooted. Nothing happens after, and the device is not showing up in ls /dev/serial/by-id/