I'm not an expert

[zoo201ok]

How can I flash it through the Arduino IDE specifically for ESP32S3 can someone help please . iknow that esos3 dose not have pin 25 And my other issue is have an installed all required library and the esp still crash boot looping

[davemaster]

what pins do you have? If you want so help, first:
1- Share circuit, board pictures
2- code, firmware, any file involved.

Best regards

[rayaninstar-oss]

what pins do you have? If you want so help, first: 1- Share circuit, board pictures 2- code, firmware, any file involved.

Best regards

mxconfig.gpio.r1 = 1;
mxconfig.gpio.g1 = 5;
mxconfig.gpio.b1 = 6;
mxconfig.gpio.r2 = 7;
mxconfig.gpio.g2 = 13;
mxconfig.gpio.b2 = 9;
mxconfig.gpio.a = 16;
mxconfig.gpio.b = 48;
mxconfig.gpio.c = 47;
mxconfig.gpio.d = 21;
mxconfig.gpio.e = 38;
mxconfig.gpio.lat = 8;
mxconfig.gpio.oe = 4;
mxconfig.gpio.clk = 18; this iis gpio and i dont know how to fix

[davemaster]

did You checked your connections match the GPIO mxconfig setup? Check it out, then SHARE all your code

[zoo201ok]

Yes the connection is solid no issues but the code i do not know how to add all that gpio to the code I've tried to change it to these gpio but in the IDE Lots of compiling error's .amd by the way the library is solid also no issue I've no idea how to get it right. I Wana change it cuz example the espS3 dose not have gpio 25 so . Only i waned those gpios .

…

On Sun, 9 Nov 2025, 5:56 pm David Elias, ***@***.***> wrote: *davemaster* left a comment (mzashh/HUB75-Pixel-Art-Display#14) <#14 (comment)> did You checked your connections match the GPIO mxconfig setup? Check it out, then SHARE all your code — Reply to this email directly, view it on GitHub <#14 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BTUMKJRLVFH7JBSCRFEU4AL335IZ7AVCNFSM6AAAAACAXNWUY2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZTKMBYGQZDQOBVGY> . You are receiving this because you authored the thread.Message ID: ***@***.***>

[davemaster]

Yes the connection is solid no issues but the code i do not know how to add
all that gpio to the code I've tried to change it to these gpio but in the
IDE Lots of compiling error's .amd by the way the library is solid also no
issue I've no idea how to get it right. I Wana change it cuz example the
espS3 dose not have gpio 25 so . Only i waned those gpios .
…

But, PUT THE CODE here, then I could guide You...

best regards

[zoo201ok]

I fixed the issue my panel was 128 by 64 but it act like the 104x52 physical pixel . My next problem is how to make the storage much higher.

…

On Sun, 9 Nov 2025, 7:48 pm David Elias, ***@***.***> wrote: *davemaster* left a comment (mzashh/HUB75-Pixel-Art-Display#14) <#14 (comment)> Yes the connection is solid no issues but the code i do not know how to add all that gpio to the code I've tried to change it to these gpio but in the IDE Lots of compiling error's .amd by the way the library is solid also no issue I've no idea how to get it right. I Wana change it cuz example the espS3 dose not have gpio 25 so . Only i waned those gpios . … <#m_-3950909734104233970_> But, PUT THE CODE here, then I could guide You... best regards — Reply to this email directly, view it on GitHub <#14 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BTUMKJV3DEBBBHTRSKM35G3335V65AVCNFSM6AAAAACAXNWUY2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZTKMBYGUYTGNJRGM> . You are receiving this because you authored the thread.Message ID: ***@***.***>