Fix: 002-test-reject-disk-with-lvm-signature.sh

Signed-off-by: Shishir Mahajan <shishir.mahajan@redhat.com>

Author: Shishir Mahajan

tests/002-test-reject-disk-with-lvm-signature.sh

@@ -7,6 +7,8 @@ test_lvm_sig() {
   local test_status=1
   local testname=`basename "$0"`
   local vg_name="css-test-foo"
+  local tmplog=${WORKDIR}/tmplog
+  local errmsg="Wipe signatures using wipefs or use WIPE_SIGNATURES=true and retry."
 
   # Error out if any pre-existing volume group vg named css-test-foo
   if vg_exists "$vg_name"; then
@@ -25,14 +27,22 @@ EOF
   done
 
   # Run container-storage-setup
-  $CSSBIN >> $LOGS 2>&1
-
-  # Css should fail. If it did not, then test failed. This is very crude
-  # check though as css can fail for so many reasons. A more precise check
-  # would be too check for exact error message.
-  [ $? -ne 0 ] && test_status=0
+  $CSSBIN > $tmplog 2>&1
+  rc=$?
+  cat $tmplog >> $LOGS 2>&1
+
+  # Test failed.
+  if [ $rc -ne 0 ]; then
+      if grep --no-messages -q "$errmsg" $tmplog; then
+          test_status=0
+      else
+          echo "ERROR: $testname: $CSSBIN Failed for a reason other then \"$errmsg\"" >> $LOGS
+      fi
+  else
+      echo "ERROR: $testname: $CSSBIN Succeeded. Should have failed since LVM2_member signature exists on devices $devs" >> $LOGS
+  fi
 
-  cleanup $vg_name "$devs"
+  cleanup "$vg_name" "$devs"
   return $test_status
 }
 

tests/libtest.sh

@@ -50,6 +50,19 @@ vg_exists() {
   return 1
 }
 
+# Tests if the physical volume pv_name exists
+pv_exists() {
+  local pv pv_name="$1"
+
+  for pv in $(pvs --noheadings -o pv_name); do
+    if [ "$pv" == "$pv_name" ]; then
+      return 0
+    fi
+  done
+  return 1
+}
+
+
 # Tests if the logical volume lv_name exists
 lv_exists() {
   local vg_name=$1
@@ -76,7 +89,14 @@ remove_pvs() {
   local dev devs=$1 pv
   for dev in $devs; do
     pv=$(lsblk -npl -o NAME "$dev" | tail -n +2 | head -1)
-    pvremove -y ${pv} >> $LOGS 2>&1
+    # If lsblk output physical volume (pv) name, pv exists on partition.
+    if [ -n "$pv" ]; then
+      pvremove -y ${pv} >> $LOGS 2>&1
+    # If lsblk output nothing, there might be a pv on block device.
+    # pv name would be same as block device name in this case.
+    elif pv_exists "$dev"; then
+      pvremove -y ${dev} >> $LOGS 2>&1
+    fi
   done
 }
 
@@ -125,8 +145,9 @@ cleanup() {
     outfile=$4
   fi
 
-
-  vgremove -y $vg_name >> $LOGS 2>&1
+  if vg_exists "$vg_name"; then
+    vgremove -y $vg_name >> $LOGS 2>&1
+  fi
   remove_pvs "$devs"
   remove_partitions "$devs"
   # After removing partitions let udev settle down. In some