Merge pull request #4190 from raspberrypi/develop

Deploy to production

Author: mudge

.gitignore

@@ -7,3 +7,4 @@ documentation/asciidoc/pico-sdk
 venv
 .venv
 .env
+.vscode

documentation/asciidoc/computers/config_txt/overclocking.adoc

@@ -15,7 +15,7 @@ WARNING: Setting any overclocking parameters to values other than those used by
 | Option | Description
 
 | arm_freq
-| Frequency of the ARM CPU in MHz.
+| Frequency of the Arm CPU in MHz.
 
 | arm_boost
 | Increases `arm_freq` to the highest supported frequency for the board-type and firmware. Set to `1` to enable.
@@ -55,7 +55,7 @@ WARNING: Setting any overclocking parameters to values other than those used by
 
 | over_voltage_sdram_p
 | SDRAM phy voltage adjustment. [-16,8] equates to [0.8V,1.4V] with 0.025V steps. Not supported on Raspberry Pi 4 or later devices.
- 
+
 | force_turbo
 | Forces turbo mode frequencies even when the ARM cores are not busy. Enabling this may set the warranty bit if `over_voltage_*` is also set.
 
@@ -111,7 +111,7 @@ This table gives the default values for the options on various Raspberry Pi mode
 
 [cols="m,^,^,^,^,^,^,^,^,^,^"]
 |===
-| Option | Pi 0/W | Pi1 | Pi2 | Pi3 | Pi3A+/Pi3B+ | CM4 & Pi4B <= R1.3 | Pi4B R1.4 | Pi 400 | Pi Zero 2 W | Pi 5
+| Option | Pi Zero W | Pi 1 | Pi 2 | Pi 3 | Pi 3A+/Pi 3B+ | CM4 & Pi 4B <= R1.3 | Pi 4B R1.4 | Pi 400 | Pi Zero 2 W | Pi 5/500/500+
 
 | arm_freq
 | 1000
@@ -171,7 +171,7 @@ This table gives the default values for the options on various Raspberry Pi mode
 | 500
 | 500
 | 300
-| 910
+| 960
 
 | hevc_freq
 | N/A

documentation/asciidoc/computers/getting-started/configuring.adoc

@@ -74,6 +74,8 @@ image::images/initial-setup/connect.png[alt="The Enable Raspberry Pi Connect pag
 
 Once your Raspberry Pi has internet access, this page helps you update your operating system and software to the latest versions. During the software update process, the wizard will remove the non-default browser if you opted to uninstall it in the browser selection step. Downloading updates may take several minutes.
 
+NOTE: If you are updating your Raspberry Pi 500+ for the first time, this can take up to half an hour. Grab a cup of coffee or go for a walk while you wait.
+
 image::images/initial-setup/update.png[alt="You can download the latest software updates during the wizard before you boot for the first time.",width="80%"]
 
 image::images/initial-setup/download.png[alt="You can download the latest software updates during the wizard before you boot for the first time.",width="80%"]

documentation/asciidoc/computers/getting-started/setting-up.adoc

@@ -26,19 +26,19 @@ You can use any high-quality power supply that provides the correct power mode.
 |Recommended power supply (voltage/current)
 |Raspberry Pi power supply
 
-|Raspberry Pi 5
+|Raspberry Pi 5 and Raspberry Pi 500
 |5V/5A, 5V/3A limits peripherals to 600mA
 |https://www.raspberrypi.com/products/27w-power-supply/[27W USB-C power supply]
 
-|Raspberry Pi 4 Model B
+|Raspberry Pi 4 Model B and Raspberry Pi 400
 |5V/3A
 |https://www.raspberrypi.com/products/type-c-power-supply/[15W USB-C power supply]
 
 |Raspberry Pi 3 (all models)
 |5V/2.5A
 |https://www.raspberrypi.com/products/micro-usb-power-supply/[12.5W Micro USB power supply]
 
-|Raspberry Pi 2 (all models)
+|Raspberry Pi 2 Model B
 |5V/2.5A
 |https://www.raspberrypi.com/products/micro-usb-power-supply/[12.5W Micro USB power supply]
 
@@ -101,22 +101,19 @@ Raspberry Pi models have the following display connectivity:
 |Model
 |Display outputs
 
-|Raspberry Pi 5
+|Raspberry Pi 5, Raspberry Pi 400 and Raspberry Pi 500
 |2× micro HDMI
 
-|Raspberry Pi 4 (all models)
+|Raspberry Pi 4 Model B
 |2× micro HDMI, audio and composite out via 3.5mm http://en.wikipedia.org/wiki/Phone_connector_(audio)#TRRS_standards[TRRS] jack
 
 |Raspberry Pi 3 (all models)
 |HDMI, audio and composite out via 3.5mm http://en.wikipedia.org/wiki/Phone_connector_(audio)#TRRS_standards[TRRS] jack
 
-|Raspberry Pi 2 (all models)
+|Raspberry Pi 2 Model B
 |HDMI, audio and composite out via 3.5mm http://en.wikipedia.org/wiki/Phone_connector_(audio)#TRRS_standards[TRRS] jack
 
-|Raspberry Pi 1 Model B+
-|HDMI, audio and composite out via 3.5mm http://en.wikipedia.org/wiki/Phone_connector_(audio)#TRRS_standards[TRRS] jack
-
-|Raspberry Pi 1 Model A+
+|Raspberry Pi 1 (all models)
 |HDMI, audio and composite out via 3.5mm http://en.wikipedia.org/wiki/Phone_connector_(audio)#TRRS_standards[TRRS] jack
 
 |Raspberry Pi Zero (all models)
@@ -142,10 +139,11 @@ All variants of the Raspberry Pi 1, 2, 3, and 4 include a 3.5mm auxiliary http:/
 The following Raspberry Pi models come with Wi-Fi and Bluetooth connectivity:
 
 * Flagship models since Raspberry Pi 3 Model B
+* All Keyboard models
 * All Zero W models
 * All Pico W models
 * Compute Modules configured with wireless (available since CM4)
 
-The "Model B" suffix indicates variants with an Ethernet port; "Model A" indicates no Ethernet port. If your Raspberry Pi doesn't have an Ethernet port, you can still connect to a wired internet connection using a USB-to-Ethernet adapter.
+The "Model B" suffix indicates variants with an Ethernet port; "Model A" indicates no Ethernet port. The Keyboard models also include an Ethernet port. If your Raspberry Pi doesn't have an Ethernet port, you can still connect to a wired internet connection using a USB-to-Ethernet adapter.
 
 image::images/peripherals/cable-net.png[alt="Plugging an Ethernet cable into a Raspberry Pi.",width="80%"]

documentation/asciidoc/computers/keyboard-computers.adoc

@@ -0,0 +1 @@
+include::keyboard-computers/intro.adoc[]