No access point after flash .bin file

[manhst]

Hi my friend,
After i flash bin file in to the board. Try to restart the board but I can't see wifi access point.
device is powered by GND and 3.3v from USB to serial pcb.

[revk]

Err, what does it say on the serial console?

[manhst]

Thank you for your response. I think I knew what was problem. Because im using S3-Mini chip. And the exiting bin file is for S1.
here is error message
ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0x7 (TG0WDT_SYS_RST),boot:0x8 (SPI_FAST_FLASH_BOOT)
Saved PC:0x40043ac8
Invalid chip id. Expected 9 read 0. Bootloader for wrong chip?
ets_main.c 329
ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0x10 (RTCWDT_RTC_RST),boot:0x8 (SPI_FAST_FLASH_BOOT)
Invalid chip id. Expected 9 read 0. Bootloader for wrong chip?
ets_main.c 329

[manhst]

Okay I manage to build bin file for S3, but got new error
ESP-ROM:esp32s3-20210327{0D}{0A}Build:Mar 27 2021{0D}{0A}rst:0x7 (TG0WDT_SYS_RST),boot:0x8 (SPI_FAST_FLASH_BOOT){0D}{0A}Saved PC:0x40050f3f{0D}{0A}SPIWP:0xee{0D}{0A}mode:DIO, clock div:2{0D}{0A}load:0x3c0e0020,len:0x4287c{0D}{0A}load:0x3fc99000,len:0x4ca0{0D}{0A}load:0x40374000,len:0x8acc{0D}{0A}load:0x42000020,len:0xd9cd4{0D}{0A}ESP-ROM:esp32s3-20210327{0D}{0A}Build:Mar 27 2021{0D}{0A}rst:0x10 (RTCWDT_RTC_RST),boot:0x8 (SPI_FAST_FLASH_BOOT){0D}{0A}SPIWP:0xee{0D}{0A}mode:DIO, clock div:2{0D}{0A}load:0x3c0e0020,len:0x4287c{0D}{0A}load:0x3fc99000,len:0x4ca0{0D}{0A}load:0x40374000,len:0x8acc{0D}{0A}load:0x42000020,len:0xd9cd4{0D}{0A}load:0x4037cacc,len:0xc45c{0D}{0A}load:0x00000000,len:0x9e70{0D}{0A}Guru Meditation Error: Core 0 panic'ed (StoreProhibited){0D}{0A}Core 0 register dump:{0D}{0A}PC : 0x40045abc PS : 0x00060530 A0 : 0x80043ab9 A1 : 0x3fceb570{0D}{0A}A2 : 0x00000000 A3 : 0x3fceb670 A4 : 0x3fceb648 A5 : 0x0d2091c5{0D}{0A}A6 : 0x00000001 A7 : 0x3fceb55c A8 : 0x00000000 A9 : 0x00000000{0D}{0A}A10 : 0x3c816160 A11 : 0x00000000 A12 : 0x00009e70 A13 : 0x00020000{0D}{0A}A14 : 0x00140000 A15 : 0x0013ffd0 SAR : 0x00000005 EXCCAUSE: 0x0000001d{0D}{0A}EXCVADDR: 0x00000000 LBEG : 0x40056f5c LEND : 0x40056f72 LCOUNT : 0xffffffff{0D}{0A}{0D}{0A}Backtrace: 0x40045abc:0x3fceb570 0x40043ab6:0x3fceb6f0 0x40034c45:0x3fceb710

[manhst]

Hi @revk , I think the error is Guru Meditation Error: Core 0 panic'ed (StoreProhibited)
May I know what is problem?
Also can you help to build BIN file for S3-Mini :(

[revk]

That is a mess formatting, but no, I don't know what the problem is there.

[Rabbit1543]

Not sure if it will help but I had to disable psram via menuconfig to get my esp32s3 to boot. FWIW this is the controller I plan in using. It comes with a 4 pin adapter that I have already soldered on and tested that it supplies power and boots l.Next step is to crimp a custom cable and install test the tx/rx.
https://shop.m5stack.com/products/m5stamp-esp32s3-module