Reorder examples

Author: nseidle

examples/Example10_SetRoverMode/Example10_SetRoverMode.ino

@@ -57,6 +57,8 @@ void setup()
   //myGNSS.setModeRoverAutomotive();
 
   myGNSS.saveConfiguration(); //Save the current configuration into non-volatile memory (NVM)
+
+  Serial.println("Configuration complete");
 }
 
 void loop()

examples/Example14_SetPPS/Example14_SetPPS.ino

@@ -57,6 +57,8 @@ void setup()
   //myGNSS.enablePPS(100000, 1000, false, 0, 0); //widthMicroseconds, periodMilliseconds, positivePolarity, rfDelayNanoSeconds, userDelayNanoseconds
 
   myGNSS.saveConfiguration(); //Save the current configuration into non-volatile memory (NVM)
+
+  Serial.println("The PPS LED should now be blinking 100ms on, 900ms off");
 }
 
 void loop()

examples/Example16_QueryDevice/Example16_QueryDevice.ino renamed to examples/Example15_QueryDevice/Example15_QueryDevice.ino

@@ -41,7 +41,7 @@ void setup()
   //We must start the serial port before using it in the library
   SerialGNSS.begin(115200, SERIAL_8N1, pin_UART1_RX, pin_UART1_TX);
 
-  myGNSS.enableDebugging(); // Print all debug to Serial
+  //myGNSS.enableDebugging(); // Print all debug to Serial
 
   if (myGNSS.begin(SerialGNSS) == false) //Give the serial port over to the library
   {

examples/Example15_PollForValidRTCMMessages/Example15_PollForValidRTCMMessages.ino renamed to examples/Example16_PollForValidRTCMMessages/Example16_PollForValidRTCMMessages.ino

@@ -60,6 +60,7 @@ void setup()
   response &= myGNSS.disableOutput();
 
   Serial.println("All characters now being echoed to UM980");
+  Serial.println("Send CONFIG to see the current configuration");
   Serial.println("Be sure both NL & CR is turned on!");
 }
 

examples/Example2_DirectConnect/Example2_DirectConnect.ino

@@ -9,7 +9,7 @@
   These examples are targeted for an ESP32 platform but any platform that has multiple
   serial UARTs should be compatible.
 
-  This example pipes all NMEA sentences to the UART.
+  This example pipes all NMEA sentences to the UART1 (the USB C port) and UART2 (connected to the microcontroller).
 
   Feel like supporting open source hardware?
   Buy a board from SparkFun!
@@ -65,7 +65,7 @@ void setup()
 
   //Configure a specific port
   float outputRate = 0.2; //0.2 = 5 reports per second.
-  char comName[] = "COM3"; //COM1, COM2, and COM3 are valid
+  char comName[] = "COM1"; //COM1, COM2, and COM3 are valid
   myGNSS.setNMEAPortMessage("GPGGA", comName, outputRate); //Message type, COM port, output rate.
   myGNSS.setNMEAPortMessage("GPGSA", comName, outputRate);
   myGNSS.setNMEAPortMessage("GPGST", comName, outputRate);

examples/Example4_EnableNMEA_5Hz/Example4_EnableNMEA_5Hz.ino

@@ -78,9 +78,9 @@ void setup()
   myGNSS.setRTCMMessage("RTCM1124", 1);
   myGNSS.setRTCMMessage("RTCM1033", 10);
 
-  myGNSS.setRTCMMessage("RTCM1033", 0); //Disable a specific message
+  //myGNSS.setRTCMMessage("RTCM1033", 0); //Example of how to disable a specific message
 
-  myGNSS.setRTCMPortMessage("RTCM1074", "COM1", 1); //Enable message on a specific port
+  //myGNSS.setRTCMPortMessage("RTCM1074", "COM1", 1); //Example of how to enable a message on a specific port
 
   myGNSS.saveConfiguration(); //Save the current configuration into non-volatile memory (NVM)
 

examples/Example6_AverageBase/Example6_AverageBase.ino

@@ -76,9 +76,9 @@ void setup()
   myGNSS.setRTCMMessage("RTCM1124", 1);
   myGNSS.setRTCMMessage("RTCM1033", 10);
 
-  //myGNSS.setRTCMMessage("RTCM1033", 0); //Disable a specific message
+  //myGNSS.setRTCMMessage("RTCM1033", 0); //Example of how to disable a specific message
 
-  //myGNSS.setRTCMPortMessage("RTCM1074", "COM1", 1); //Enable message on a specific port
+  //myGNSS.setRTCMPortMessage("RTCM1074", "COM1", 1); //Example of how to enable a message on a specific port
 
   myGNSS.saveConfiguration(); //Save the current configuration into non-volatile memory (NVM)
 

examples/Example7_FixedBase/Example7_FixedBase.ino

@@ -54,6 +54,8 @@ void setup()
   myGNSS.setMinCNO(10); //Set the minimum CN0 value to 10 dBHz
 
   myGNSS.saveConfiguration(); //Save the current configuration into non-volatile memory (NVM)
+
+  Serial.println("Configuration complete");
 }
 
 void loop()