USB peripheral support

Cargo.toml

@@ -19,6 +19,8 @@ bitflags = "1.2"
 vcell = "0.1"
 static_assertions = "1.1"
 fugit = "0.3.5"
+stm32-usbd = { version = "0.7.0", optional = true }
+critical-section = "1.1.2"
 
 [dependencies.cortex-m]
 version = "0.7.7"
@@ -71,11 +73,14 @@ cfg-if = "0.1.10"
 mpu6050 = "0.1.4"
 bme680 = "0.6.0"
 embedded-sdmmc = "0.3.0"
+usb-device = { version = "0.3.2", features = ["defmt"] }
+usbd-serial = "0.2.2"
 
 #TODO: Separate feature sets
 [features]
 default = ["rt"]
 rt = ["stm32g4/rt"]
+usb = ["dep:stm32-usbd"]
 stm32g431 = ["stm32g4/stm32g431"]
 stm32g441 = ["stm32g4/stm32g441"]
 stm32g471 = ["stm32g4/stm32g471"]

examples/usb_serial.rs

@@ -0,0 +1,90 @@
+//! CDC-ACM serial port example using polling in a busy loop.
+#![deny(warnings)]
+#![deny(unsafe_code)]
+#![no_std]
+#![no_main]
+
+use cortex_m_rt::entry;
+use hal::prelude::*;
+use hal::pwr::PwrExt;
+use hal::usb::{Peripheral, UsbBus};
+use hal::{rcc, stm32};
+use stm32g4xx_hal as hal;
+
+use usb_device::prelude::*;
+use usbd_serial::{SerialPort, USB_CLASS_CDC};
+
+use panic_probe as _;
+
+#[macro_use]
+mod utils;
+
+#[entry]
+fn main() -> ! {
+    utils::logger::init();
+
+    let dp = stm32::Peripherals::take().expect("cannot take peripherals");
+    let pwr = dp.PWR.constrain().freeze();
+    let mut rcc = dp.RCC.freeze(rcc::Config::hsi(), pwr);
+    rcc.enable_hsi48();
+
+    let gpioa = dp.GPIOA.split(&mut rcc);
+
+    let mut led = gpioa.pa5.into_push_pull_output();
+    led.set_low().ok();
+
+    let usb_dm = gpioa.pa11.into_alternate();
+    let usb_dp = gpioa.pa12.into_alternate();
+
+    let usb = Peripheral {
+        usb: dp.USB,
+        pin_dm: usb_dm,
+        pin_dp: usb_dp,
+    };
+    let usb_bus = UsbBus::new(usb);
+
+    let mut serial = SerialPort::new(&usb_bus);
+
+    let mut usb_dev = UsbDeviceBuilder::new(&usb_bus, UsbVidPid(0x16c0, 0x27dd))
+        .strings(&[StringDescriptors::default()
+            .manufacturer("Fake company")
+            .product("Serial port")
+            .serial_number("TEST")])
+        .unwrap()
+        .device_class(USB_CLASS_CDC)
+        .build();
+
+    loop {
+        if !usb_dev.poll(&mut [&mut serial]) {
+            continue;
+        }
+
+        let mut buf = [0u8; 64];
+
+        match serial.read(&mut buf) {
+            Ok(count) if count > 0 => {
+                led.set_high().ok();
+
+                // Echo back in upper case
+                for c in buf[0..count].iter_mut() {
+                    if 0x61 <= *c && *c <= 0x7a {
+                        *c &= !0x20;
+                    }
+                }
+
+                let mut write_offset = 0;
+                while write_offset < count {
+                    match serial.write(&buf[write_offset..count]) {
+                        Ok(len) if len > 0 => {
+                            write_offset += len;
+                        }
+                        _ => {}
+                    }
+                }
+            }
+            _ => {}
+        }
+
+        led.set_low().ok();
+    }
+}

src/gpio.rs

@@ -342,6 +342,8 @@ macro_rules! gpio {
                     _mode: PhantomData<MODE>,
                 }
 
+                impl<MODE> crate::Sealed for $PXi<MODE> {}
+
                 #[allow(clippy::from_over_into)]
                 impl Into<$PXi<Input<PullDown>>> for $PXi<DefaultMode> {
                     fn into(self) -> $PXi<Input<PullDown>> {

src/lib.rs

@@ -98,3 +98,5 @@ pub mod time;
 pub mod timer;
 // pub mod watchdog;
 pub mod independent_watchdog;
+#[cfg(feature = "usb")]
+pub mod usb;

src/rcc/mod.rs

@@ -440,6 +440,11 @@ impl Rcc {
         while self.rb.csr.read().lsirdy().bit_is_clear() {}
     }
 
+    pub fn enable_hsi48(&self) {
+        self.rb.crrcr.modify(|_, w| w.hsi48on().set_bit());
+        while self.rb.crrcr.read().hsi48rdy().bit_is_clear() {}
+    }
+
     pub fn get_reset_reason(&self) -> ResetReason {
         let csr = self.rb.csr.read();
 

src/usb.rs

@@ -0,0 +1,69 @@
+//! USB peripheral.
+//!
+//! Provides the required implementation for use of the [`stm32-usbd`] crate.
+
+pub use stm32_usbd::UsbBus;
+
+use crate::gpio;
+use crate::gpio::gpioa::{PA11, PA12};
+use crate::rcc::{Enable, Reset};
+use crate::stm32::{RCC, USB};
+use core::fmt;
+use stm32_usbd::UsbPeripheral;
+
+/// Trait implemented by all pins that can be the "D-" pin for the USB peripheral
+pub trait DmPin: crate::Sealed {}
+
+/// Trait implemented by all pins that can be the "D+" pin for the USB peripheral
+pub trait DpPin: crate::Sealed {}
+
+impl DmPin for PA11<gpio::Alternate<{ gpio::AF14 }>> {}
+impl DpPin for PA12<gpio::Alternate<{ gpio::AF14 }>> {}
+
+pub struct Peripheral<Dm: DmPin, Dp: DpPin> {
+    /// USB register block
+    pub usb: USB,
+    /// Data negative pin
+    pub pin_dm: Dm,
+    /// Data positive pin
+    pub pin_dp: Dp,
+}
+
+impl<Dm, Dp> fmt::Debug for Peripheral<Dm, Dp>
+where
+    Dm: DmPin + fmt::Debug,
+    Dp: DpPin + fmt::Debug,
+{
+    fn fmt(&self, f: &mut fmt::Formatter<'_>) -> fmt::Result {
+        f.debug_struct("Peripheral")
+            .field("usb", &"USB")
+            .field("pin_dm", &self.pin_dm)
+            .field("pin_dp", &self.pin_dp)
+            .finish()
+    }
+}
+
+// SAFETY: Implementation of Peripheral is thread-safe by using cricitcal sections to ensure
+// mutually exclusive access to the USB peripheral
+unsafe impl<Dm: DmPin, Dp: DpPin> Sync for Peripheral<Dm, Dp> {}
+
+// SAFETY: The peripheral has the same regiter blockout as the STM32 USBFS
+unsafe impl<Dm: DmPin + Send, Dp: DpPin + Send> UsbPeripheral for Peripheral<Dm, Dp> {
+    const REGISTERS: *const () = USB::ptr().cast::<()>();
+    const DP_PULL_UP_FEATURE: bool = true;
+    const EP_MEMORY: *const () = 0x4000_6000 as _;
+    const EP_MEMORY_SIZE: usize = 1024;
+    const EP_MEMORY_ACCESS_2X16: bool = true;
+
+    fn enable() {
+        critical_section::with(|_| unsafe {
+            let rcc_ptr = &(*RCC::ptr());
+            USB::enable(rcc_ptr);
+            USB::reset(rcc_ptr);
+        });
+    }
+
+    fn startup_delay() {
+        // not required
+    }
+}