STM32CubeWL: add additional debug output

This adds some more details about RX and TX bytes and TX config. There
is also some code for RX config, but to minimize the impact on RX
timing, that is commented out.

Author: matthijskooijman

src/STM32CubeWL/LoRaWAN/Mac/LoRaMac.c

@@ -1140,6 +1140,11 @@ static void ProcessRadioRxDone( void )
 #endif /* LORAMAC_VERSION */
     Mlme_t joinType = MLME_JOIN;
 
+    MW_LOG( TS_ON, VLEVEL_M, "RX: ");
+    for (size_t i = 0; i < RxDoneParams.Size; ++i)
+        MW_LOG( TS_ON, VLEVEL_M, "%02x", RxDoneParams.Payload[i]);
+    MW_LOG( TS_ON, VLEVEL_M, "\r\n");
+
 #if (defined( LORAMAC_VERSION ) && (( LORAMAC_VERSION == 0x01000400 ) || ( LORAMAC_VERSION == 0x01010100 )))
     LoRaMacRadioEvents.Events.RxProcessPending = 0;
 #endif /* LORAMAC_VERSION */

src/STM32CubeWL/SubGHz_Phy/stm32_radio_driver/radio.c

@@ -871,6 +871,18 @@ static void RadioSetRxConfig( RadioModems_t modem, uint32_t bandwidth,
 #if (RADIO_SIGFOX_ENABLE == 1)
     uint8_t modReg;
 #endif
+    //Disabled, too much influence on RX timing
+    /*
+    MW_LOG( TS_ON, VLEVEL_M,
+        "Setting RX Config: modem=%s, bandwidth=%u, datarate=%u, coderate=%u bandwithAfc=%u, preambleLen=%u, symbTimeout=%u, fixLen=%u, payloadLen=%u, crcOn=%u, freqHopOn=%u, hopPeriod=%u, iqInverted=%u, rxContinuous=%u\r\n",
+        modem == MODEM_FSK ? "MODEM_FSK" : (modem == MODEM_LORA ? "MODEM_LORA" : "?"),
+        (unsigned)bandwidth, (unsigned)datarate, (unsigned)coderate,
+        (unsigned)bandwidthAfc, (unsigned)preambleLen,
+        (unsigned)symbTimeout, (unsigned)fixLen, (unsigned)payloadLen,
+        (unsigned)crcOn, (unsigned)freqHopOn, (unsigned)hopPeriod,
+        (unsigned)iqInverted, (unsigned)rxContinuous
+    );
+    */
     SubgRf.RxContinuous = rxContinuous;
     RFW_DeInit();
     if( rxContinuous == true )
@@ -1060,6 +1072,15 @@ static void RadioSetTxConfig( RadioModems_t modem, int8_t power, uint32_t fdev,
     SubgRf.lr_fhss.is_lr_fhss_on = false;
 #endif /* RADIO_LR_FHSS_IS_ON == 1 */
     RFW_DeInit();
+    MW_LOG( TS_ON, VLEVEL_M,
+        "Setting TX Config: modem=%s, power=%u, fdev=%u, bandwidth=%u, datarate=%u, coderate=%u preambleLen=%u, fixLen=%u, crcOn=%u, freqHopOn=%u, hopPeriod=%u, iqInverted=%u, timeout=%u\r\n",
+        modem == MODEM_FSK ? "MODEM_FSK" : (modem == MODEM_LORA ? "MODEM_LORA" : "?"),
+        (int)power, (unsigned)fdev, (unsigned)bandwidth,
+        (unsigned)datarate, (unsigned)coderate, (unsigned)preambleLen,
+        (unsigned)fixLen, (unsigned)crcOn, (unsigned)freqHopOn,
+        (unsigned)hopPeriod, (unsigned)iqInverted, (unsigned)timeout
+    );
+
     switch( modem )
     {
         case MODEM_FSK:
@@ -1318,6 +1339,11 @@ static radio_status_t RadioSend( uint8_t *buffer, uint8_t size )
                             IRQ_RADIO_NONE,
                             IRQ_RADIO_NONE );
 
+    MW_LOG( TS_ON, VLEVEL_M, "TX:");
+    for (size_t i = 0; i < size; ++i)
+        MW_LOG( TS_ON, VLEVEL_M, " %02x", buffer[i]);
+    MW_LOG( TS_ON, VLEVEL_M, "\r\n");
+
     /* Set DBG pin */
     DBG_GPIO_RADIO_TX( SET );