Fix coding style

Author: dingsen-Greenhorn

vwifi.c

@@ -88,8 +88,8 @@ struct vwifi_vif {
     struct wireless_dev wdev;
     struct net_device *ndev;
     struct net_device_stats stats;
-    int manual_mcs;    
-    bool manual_mcs_set; 
+    int manual_mcs;
+    bool manual_mcs_set;
     size_t ssid_len;
     /* Currently connected BSS id */
     u8 bssid[ETH_ALEN];
@@ -1405,7 +1405,7 @@ static int vwifi_get_station(struct wiphy *wiphy,
     sinfo->rx_bytes = vif->stats.rx_bytes;
 
 
-    /* Log byte counters for debugging */ 
+    /* Log byte counters for debugging */
     pr_info(
         "vwifi: Station %pM tx_bytes %llu, rx_bytes %llu, tx_packets %u, "
         "rx_packets %u, tx_failed %u\n",
@@ -1414,8 +1414,7 @@ static int vwifi_get_station(struct wiphy *wiphy,
 
     /* For CFG80211_SIGNAL_TYPE_MBM, value is expressed in dBm */
     sinfo->signal = rand_int_smooth(-100, -30, jiffies);
-    pr_info("vwifi: Station %pM signal %d dBm (raw)\n", mac,
-            sinfo->signal); 
+    pr_info("vwifi: Station %pM signal %d dBm (raw)\n", mac, sinfo->signal);
     sinfo->inactive_time = jiffies_to_msecs(jiffies - vif->active_time);
     /*
      * Using 802.11n (HT) as the PHY, configure as follows:
@@ -1742,14 +1741,14 @@ static int vwifi_start_ap(struct wiphy *wiphy,
 
     /* Initialize hrtimer of beacon */
     pr_info("vwifi: init beacon_timer.\n");
-    #if LINUX_VERSION_CODE >= KERNEL_VERSION(6, 15, 0)
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(6, 15, 0)
     hrtimer_setup(&vif->beacon_timer, vwifi_beacon, CLOCK_MONOTONIC,
-        HRTIMER_MODE_ABS_SOFT);
-    #else
+                  HRTIMER_MODE_ABS_SOFT);
+#else
     hrtimer_init(&vif->beacon_timer, CLOCK_MONOTONIC, HRTIMER_MODE_ABS_SOFT);
     vif->beacon_timer.function = vwifi_beacon;
-    #endif
-    
+#endif
+
     if (!hrtimer_is_queued(&vif->beacon_timer)) {
         u64 tsf, until_tbtt;
         tsf = ktime_to_us(ktime_get_real());
@@ -2304,24 +2303,27 @@ static struct cfg80211_ops vwifi_cfg_ops = {
 };
 
 /* Macro for defining 2GHZ channel array */
-#define CHAN_2GHZ(channel, freq)                          \
-    {                                                     \
-        .band = NL80211_BAND_2GHZ, .hw_value = (channel), \
-        .center_freq = (freq),                            \
+#define CHAN_2GHZ(channel, freq)   \
+    {                              \
+        .band = NL80211_BAND_2GHZ, \
+        .hw_value = (channel),     \
+        .center_freq = (freq),     \
     }
 
 /* Macro for defining 5GHZ channel array */
-#define CHAN_5GHZ(channel)                                \
-    {                                                     \
-        .band = NL80211_BAND_5GHZ, .hw_value = (channel), \
-        .center_freq = 5000 + (5 * (channel)),            \
+#define CHAN_5GHZ(channel)                     \
+    {                                          \
+        .band = NL80211_BAND_5GHZ,             \
+        .hw_value = (channel),                 \
+        .center_freq = 5000 + (5 * (channel)), \
     }
 
 
 /* Macro for defining rate table */
-#define RATE_ENT(_rate, _hw_value)                   \
-    {                                                \
-        .bitrate = (_rate), .hw_value = (_hw_value), \
+#define RATE_ENT(_rate, _hw_value) \
+    {                              \
+        .bitrate = (_rate),        \
+        .hw_value = (_hw_value),   \
     }
 
 /* Array of "supported" channels in 2GHz band. It is required for wiphy. */