Wireguard installation failure on pivpn.io - Fall back to direct link?

[drthanwho]

This could likely be a network issue, although I'm not sure why since I have DNS servers configured to 8.8.8.8 and 1.1.1.1.
And I'm also having the exact same isssue on two seperare proxmox servers on two seperate networks.

Funnily enough I have isntalled wireguard in the past just fine and network wise haven't done any changes.

I'm getting the following

 ✓ Installed Dependencies
 - Installing WireGuard (using pivpn.io)  /curl: (28) Failed to connect to install.pivpn.io port 443: Connection timed out
/dev/fd/63: line 1: $'\E[?25h': command not found
/dev/fd/63: line 2: $'\E[01': command not found
/dev/fd/63: line 2: $'31m[ERROR]\E[m': command not found
/dev/fd/63: line 2: $'31m40\E[m:': command not found
/dev/fd/63: line 2: $'31m0\E[m:': command not found

[ERROR] in line 40: exit code 0: while executing command $STD bash <(curl -fsSL https://install.pivpn.io) --unattended options.conf

root@sweetmamproxmox:~# cat /etc/resolv.conf
search local
nameserver 8.8.8.8
nameserver 1.1.1.1
root@sweetmamproxmox:~# 

If I try a curl on the github direct link --> https://raw.githubusercontent.com/pivpn/pivpn/master/auto_install/install.sh
it resolves immediately. Maybe an option that if pivpn.io times out it fallbacks to the github link?

[tteck]

 _       ___           ______                     __
| |     / (_)_______  / ____/_  ______ __________/ /
| | /| / / / ___/ _ \/ / __/ / / / __ `/ ___/ __  / 
| |/ |/ / / /  /  __/ /_/ / /_/ / /_/ / /  / /_/ /  
|__/|__/_/_/   \___/\____/\__,_/\__,_/_/   \__,_/   
                                                    
Using Advanced Settings
Using Distribution: debian
Using debian Version: 11
Using Container Type: 1
Using Root Password: Automatic Login
Container ID: 111
Using Hostname: wireguard
Using Disk Size: 2
Allocated Cores: 1
Allocated RAM: 512
Using Bridge: vmbr0
Using IP Address: dhcp
Using Gateway IP Address: Default
Using APT-Cacher IP Address: Default
Disable IPv6: yes
Using Interface MTU Size: Default
Using DNS Search Domain: Host
Using DNS Server IP Address: Host
Using MAC Address: AE:1A:60:07:B7:59
Using Vlan: Default
Enable Root SSH Access: no
Enable Verbose Mode: no
Creating a Wireguard LXC using the above advanced settings
 ✓ Using local for Template Storage.
 ✓ Using local-lvm for Container Storage.
 ✓ Updated LXC Template List
 ✓ LXC Container 111 was successfully created.
 ✓ Started LXC Container
 ✓ Set up Container OS
 ✓ Network Connected: 192.168.86.253 
 ✓ Internet Connected
 ✓ DNS Resolved github.com to 140.82.112.3
 ✓ Updated Container OS
 ✓ Installed Dependencies
 ✓ Installed WireGuard
 ✓ Customized Container
 ✓ Cleaned
 ✓ Completed Successfully!

Debian 11

[drthanwho]

Hmm well now it seems to be working again! Maybe they were down briefly I don't know what else to think